Ford E-350 Recall for Power Train Problem - (14 Recalls Found)
Find your car listed below. Results are sorted year from newest to oldest. Select the desired vehicle to view the complete details.
Information provided by the National Highway Traffic Safety Administration.
|
|
|
Problem: Ford Motor Company (Ford) is recalling certain 2020 F-550 and 2021 E-350 and E-450 vehicles. The rear axle differential fluid may be below the minimum level, possibly resulting in a failure of the rear axle assembly and driveshaft separation. Recall Details
Problem: Ford Motor Company (Ford) is recalling certain 2020 F-550 and 2021 E-350 and E-450 vehicles. The rear axle differential fluid may be below the minimum level, possibly resulting in a failure of the rear axle assembly and driveshaft separation. Recall Details
Problem: FORD IS RECALLING 3,331 MY 2008 E-350 VEHICLES BUILT WITH A 138 INCH WHEEL BASE. THE DRIVE SHAFT MAY HAVE BEEN MANUFACTURED WITH A SLIP YOKE THAT HAS CRACKS. THE EFFECT OF THE CRACKS ON FATIGUE PERFORMANCE IS VARIABLE, BUT ON SOME YOKES WITH CRACKS, THE PERFORMANCE IS REDUCED BELOW DESIGN SPECIFICATION. Recall Details
Problem: VEHICLE DESCRIPTION: PICKUP TRUCKS BUILT WITH SINGLE REAR WHEELS AND EQUIPPED WITH 3.55:1 AND 3.73:1 AXLE RATIO. THESE VEHICLES WERE BUILT WITH INCORRECT SPEEDOMETER DRIVEN GEARS, RESULTING IN A LOWER SPEEDOMETER READING THAN THE ACTUAL VEHICLE SPEED BEING DRIVEN. Recall Details
Problem: UNDER CERTAIN CONDITIONS, THE SNAP RING THAT LOCATES THE PARK GEAR ON THE OUTPUT SHAFT OF THE TRANSMISSION MAY FRACTURE. Recall Details
Problem: UNDER CERTAIN CONDITIONS, THE SNAP RING THAT LOCATES THE PARK GEAR ON THE OUTPUT SHAFT OF THE TRANSMISSION MAY FRACTURE. Recall Details
Problem: COMPOSITE GRAPHITE DRIVESHAFTS ARE SUBJECT TO OVERHEATING WHILE IDLING, WHICH MAY RESULT IN THE DRIVESHAFT TWISTING AND SHORTENING CAUSING THE SLIP YOKE TO DISCONNECT FROM THE TRANSMISSION. CONSEQUENCE OF DEFECT: IF THE DRIVESHAFT DISCONNECTS FROM THE TRANSMISSION THE VEHICLE WOULD BECOME IMMOBILE WITHOUT WARNING. Recall Details
Problem: COMPOSITE GRAPHITE DRIVESHAFTS ARE SUBJECT TO OVERHEATING WHILE IDLING, WHICH MAY RESULT IN THE DRIVESHAFT TWISTING AND SHORTENING CAUSING THE SLIP YOKE TO DISCONNECT FROM THE TRANSMISSION. CONSEQUENCE OF DEFECT: IF THE DRIVESHAFT DISCONNECTS FROM THE TRANSMISSION THE VEHICLE WOULD BECOME IMMOBILE WITHOUT WARNING. Recall Details
Problem: COMPOSITE GRAPHITE DRIVESHAFTS ARE SUBJECT TO OVERHEATING WHILE IDLING, WHICH MAY RESULT IN THE DRIVESHAFT TWISTING AND SHORTENING CAUSING THE SLIP YOKE TO DISCONNECT FROM THE TRANSMISSION. CONSEQUENCE OF DEFECT: IF THE DRIVESHAFT DISCONNECTS FROM THE TRANSMISSION THE VEHICLE WOULD BECOME IMMOBILE WITHOUT WARNING. Recall Details
Problem: ON CERTAIN VEHICLES, THE LOCK WEDGES USED TO SECURE THE AXLE BEARING NUTS TO THE AXLE HOUSING MAY FALL OUT OF POSITION, ALLOWING THE NUT TO LOOSEN. THE NUT ON THE LEFT SIDE MAY FALL OFF, ALLOWING MOVEMENT OF THE AXLE SHAFT. Recall Details
Problem: ON SOME OF THE INVOLVED VEHICLES, THE SHIFT ROD IN THE TRANSMISSION MAY NOT BE PROPERLY SEATED IN THE RETENTION GROMMET OF THE STEERING COLUMN SHIFT LEVER ASSEMBLY. IF THE SHIFT ROD WERE TO DISENGAGE, THE DRIVER COULD NOT SELECT THE PROPER TRANSMISSION FUNCTION WHICH WOULD CREATE THE POTENTIAL FOR UNEXPECTED MOVEMENT OF THE VEHICLE. Recall Details
Problem: ON CERTAIN VEHICLES, THE LOCK WEDGES USED TO SECURE THE AXLE BEARING NUTS TO THE AXLE HOUSING MAY FALL OUT OF POSITION, ALLOWING THE NUT TO LOOSEN. THE NUT ON THE LEFT SIDE MAY FALL OFF, ALLOWING MOVEMENT OF THE AXLE SHAFT. Recall Details
Problem: ON THE INVOLVED VEHICLES, THE PARK ACTUATION SUPPORT PLATES ARE DEFECTIVE DUE TO THEIR SUSCEPTIBILITY TO CRACKING DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. AS A RESULT, FRAGMENTS FROM A BROKEN PLATE CAN BECOME LODGED IN THE TRANSMISSION PARKING PAWL MECHANISM. THIS COULD PREVENT THE TRANSMISSION PARKING PAWL FROM ENGAGING WHEN THE SELECTOR LEVER IS PLACED IN THE "PARK" POSITION, OR PREVENT THE PAWL FROM BEING DISENGAGED FROM THE PARK GEAR. Recall Details
Problem: THE SHIFT SELECTOR REACTION SPRINGS MAY BE DEFORMED AS A RESULT OF IMPROPER INSTALLATION OF SELECTOR LEVERS DURING COLUMN BUILDUP. THUS THE LEVER MAY NOT BE ABLE TO BE MOVED INTO THE INSERT DETENTS LOCATED IN THE STEERING COLUMN ASSEMBLY. THIS COULD PREVENT THE "PARK" GEAR FROM BEING ENGAGED. Recall Details
|