2007 NISSAN MAXIMA RECALL - #06V402000
RECALL FOR STEERING : COLUMN LOCKING : ANTI-THEFT DEVICE
CERTAIN PASSENGER VEHICLES EQUIPPED WITH AN 'INTELLIGENT KEY' FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION." DURING AN INSPECTION OF SOME VEHICLES AT THE ASSEMBLY PLANT, IT WAS FOUND THAT THE STEERING WHEEL WAS LOCKED WITH THE IGNITION KNOB IN THE "OFF" POSITION BUT THE VEHICLE TRANSMISSION NOT BEING IN THE "PARK" POSITION.
Information provided by the
National Highway Traffic Safety Administration.
•
Send to a friend
•
Hide Form
Recall Details
| Vehicle |
2007 NISSAN MAXIMA |
|
| Manufacturer |
NISSAN NORTH AMERICA, INC. |
| Manufactured between |
5/25/2006 - 7/20/2006 |
| Recalled on |
10/23/2006 |
| Influenced by |
NISSAN NORTH AMERICA, INC. |
| Owners Notified on |
12/18/2006 |
| # Affected |
9,506 |
| Recalled for |
STEERING:COLUMN LOCKING:ANTI-THEFT DEVICE |
|
|
| Description |
CERTAIN PASSENGER VEHICLES EQUIPPED WITH AN 'INTELLIGENT KEY' FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION." DURING AN INSPECTION OF SOME VEHICLES AT THE ASSEMBLY PLANT, IT WAS FOUND THAT THE STEERING WHEEL WAS LOCKED WITH THE IGNITION KNOB IN THE "OFF" POSITION BUT THE VEHICLE TRANSMISSION NOT BEING IN THE "PARK" POSITION. |
| Consequences |
IF THE KEY IS TURNED TO THE "OFF" POSITION WITHOUT THE TRANSMISSION BEING IN THE "PARK" POSITION, IT IS POSSIBLE THAT THE STEERING WHEEL CAN LOCK WHEN TURNED TO THE RIGHT. |
| Corrective action |
DEALERS WILL INSPECT AND REPLACE THE STEERING WHEEL LOCK ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 18, 2006. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261. |
| Notes |
NISSAN RECALL NO. PB026.CUSTOMERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO HTTP://WWW.SAFERCAR.GOV. |
| See also |
|
| Technical Service Bulletins |
May 10, 2021 - 010000 STEERING
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut P
May 10, 2021 - 010000 STEERING
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when imprope
May 10, 2021 - 010000 STEERING
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into
May 10, 2021 - 020000 SUSPENSION
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition wh
May 10, 2021 - 020000 SUSPENSION
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into
View all Technical Service Bulletins
|
|