|
Problem: VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS AND SCHOOL BUS CHASSIS-COWLS EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE WELDS THAT ATTACH THE KEY TO THE TOP OF THE STEERING COLUMN MOUNTED AUTOMATIC TRANSMISSION SHIFT LINKAGE MAY NOT ADEQUATELY RETAIN THE KEY, ALLOWING THE TRANSMISSION TO BE IN A GEAR OTHER THAN THAT INDICATED ON THE "PRNDL", OR IN SOME CASES, "RNDL." Recall Details
Problem: VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS AND CHASSIS-CABS. AN AUTOMATIC LOCKING FRONT WHEEL BEARING ADJUSTING NUT WAS DAMAGED DURING INSTALLATION OR REMOVAL BY INCORRECT TOOLS OR AN INCORRECT TORQUE SPECIFICATION WAS USED. Recall Details
Problem: THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES. Recall Details
Problem: THE VEHICLES WERE MANUFACTURED WITHOUT SEPARATE ABS INDICATOR LAMPS. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 105, "HYDRAULIC BRAKE SYSTEMS." Recall Details
Problem: THE DRAG LINK INSTALLED CAN CONTACT THE FRONT AXLE I-BEAM UNDER CERTAIN EXTREME CONDITIONS. THIS DRAG LINK WAS NOT INTENDED TO BE INSTALLED ON "LOW PROFILE" VEHICLES. Recall Details
Problem: A CONNECTOR IN THE WIRING WHERE THE TILT HOOD MOUNTED LAMPS ATTACH TO THE VEHICLE WIRING HARNESS WAS BUILT WITHOUT SEALING PLUGS. MOISTURE, ROAD SALT OR OTHER CONTAMINANTS CAN ENTER THE CONNECTION RESULTING IN CROSSED CIRCUITS, SHORTS OR CORROSION OF THE WIRING OF THE CONNECTOR. Recall Details
Problem: A CONNECTOR IN THE WIRING WHERE THE TILT HOOD MOUNTED LAMPS ATTACH TO THE VEHICLE WIRING HARNESS WAS BUILT WITHOUT SEALING PLUGS. MOISTURE, ROAD SALT OR OTHER CONTAMINANTS CAN ENTER THE CONNECTION RESULTING IN CROSSED CIRCUITS, SHORTS OR CORROSION OF THE WIRING OF THE CONNECTOR. Recall Details
Problem: THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES. Recall Details
Problem: THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES. Recall Details
Problem: Recall Details
Problem: AS A RESULT OF INHERENT VIBRATION IN THESE ENGINES, THE THROTTLE RETURN SPRINGS CAN FRACTURE. Recall Details
Problem: AS A RESULT OF INHERENT VIBRATION IN THESE ENGINES, THE THROTTLE RETURN SPRINGS CAN FRACTURE. Recall Details
Problem: WATER CAN ENTER THE DOOR LATCH RELEASE CABLE. IF THE VEHICLE IS OPERATED IN BELOW FREEZING TEMPERATURES, THE WATER IN THE DOOR LATCH RELEASE CABLE CAN FREEZE AND CAUSE THE LATCH MECHANISM TO MALFUNCTION. Recall Details
Problem: THE THROTTLE CABLE WHICH RUNS FROM THE ACCELERATOR TO THE GOVERNOR ASSEMBLY HOUSING MAY HAVE BEEN KINKED DURING ASSEMBLY, CAUSING EXCESSIVE WEAR OF THE CABLE HOUSING INNER LINING. THIS COULD RESULT IN EITHER FRACTURE OR STICKING OF THE CABLE. Recall Details
Problem: THE THROTTLE CABLE WHICH RUNS FROM THE ACCELERATOR TO THE GOVERNOR ASSEMBLY HOUSING MAY HAVE BEEN KINKED DURING ASSEMBLY, CAUSING EXCESSIVE WEAR OF THE CABLE HOUSING INNER LINING. THIS COULD RESULT IN EITHER FRACTURE OR STICKING OF THE CABLE. Recall Details
Problem: THE INVOLVED VEHICLES WERE PRODUCED WITH HYDRAULIC BRAKE BOOSTER SUPPLY HOSES THAT ARE LOCATED TOO CLOSE TO THE ENGINE EXHAUST MANIFOLD AND MAY CHAFE AND DEVELOP HEAT DAMAGE DURING VEHICLE OPERATION. CHAFING AND HEAT INDUCED DETERIORATION OF A HOSE DUE TO DIRECT CONTACT WITH THE MANIFOLD MAY CAUSE THE HOSE TO WEAR. A SUBSEQUENT RUPTURE WILL RESULT IN PUMP FLUID LOSS. Recall Details
Problem: ON THE AFFECTED VEHICLES, THE WIRING ASSEMBLY TO THE FLOOR MOUNTED HEADLAMP DIMMER SWITCH MAY BE TOO TIGHT; SHOULD WIRES DISCONNECT, THE HEADLIGHTS WILL NOT OPERATE. Recall Details
Problem: TWO-INCH SPACERS SPECIFIED FOR INSTALLATION BETWEEN THE FRONT AXLES AND EACH FRONT SPRING ASSEMBLY WERE OMITTED DURING MANUFACTURE. UNDER CERTAIN TURNING AND BOUNCING CONDITIONS, A FRONT TIRE COULD CONTACT ADJACENT VEHICLE COMPONENTS, RESULTING IN A POSSIBLE SEPARATION OF THE DRAG LINK TO STEERING ARM BALLJOINT OR LOSS OF TIRE PRESSURE. Recall Details
Problem: THE PRIMARY CIRCUIT CONNECTION, WHICH PROVIDES PRIMARY ELECTRICAL POWER TO THE ENGINE, COULD DETERIORATE DUE TO HIGH CURRENT DRAW PRODUCED BY BUILDER-INSTALLED EQUIPMENT. Recall Details
Problem: THE INVOLVED VEHICLES WERE ASSEMBLED WITH THE LEFT FRONT BRAKE TUBE RETAINING CLIP MISSING. THE ABSENCE OF A RETAINING CLIP MAY ALLOW THE BRAKE TUBE TO RUB AGAINST THE SHOCK ABSORBER, CAUSING WEAR ON THE TUBE AND, EVENTUALLY, LOSS OF BRAKE FLUID. Recall Details
Problem: THE MASTER CYLINDER TO CHASIS BRAKE TUBE AND HOSE ASSEMBLIES MAY HAVE BEEN MOVED FROM THEIR INTENDED POSITION, WHICH COULD ALLOW CHAFING AGAINST UNDERBODY COMPONENTS. CHAFING PROMOTES WEAR OF THE BRAKE TUBE AND HOSE ASSEMBLY AND COULD CAUSE A LOSS OF BRAKE FLUID. Recall Details
Problem: THE MASTER CYLINDER TO CHASIS BRAKE TUBE AND HOSE ASSEMBLIES MAY HAVE BEEN MOVED FROM THEIR INTENDED POSITION, WHICH COULD ALLOW CHAFING AGAINST UNDERBODY COMPONENTS. CHAFING PROMOTES WEAR OF THE BRAKE TUBE AND HOSE ASSEMBLY AND COULD CAUSE A LOSS OF BRAKE FLUID. Recall Details
Problem: THE PRIMARY CIRCUIT CONNECTION, WHICH PROVIDES PRIMARY ELECTRICAL POWER TO THE ENGINE, COULD DETERIORATE DUE TO HIGH CURRENT DRAW PRODUCED BY BUILDER-INSTALLED EQUIPMENT. Recall Details
Problem: THE AIR BRAKE LINES MAY BE ROUTED TOO CLOSE TO THE EXHAUST MUFFLER. BECAUSE THE AIR BRAKE LINES ARE MADE OF NYLON MATERIAL, HEAT FROM THE EXHAUST MUFFLER CAN WEAKEN THE BRAKE LINE TUBES, POSSIBLY CAUSING THEM TO RUPTURE. TUBE RUPTURE COULD RESULT IN LOSS OF AIR IN THE SECONDARY AIR BRAKE SYSTEM. Recall Details
|