|
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: NAVISTAR HAS NOTIFIED NHTSA OF A DEFECT ON CERTAIN MODEL YEAR 2008-2011 INTERNATIONAL TRUCKS EQUIPPED WITH AN OPTIONAL JUMP START STUD. CORROSION AT THE BASE OF THE STUD MAY CAUSE AN ELECTRICAL SHORT BETWEEN THE STUD AND BATTERY BOX. Recall Details
Problem: ON CERTAIN TRUCKS, ONE OR BOTH REAR AXLE HOUSINGS MAY CONTAIN THINNER MATERIAL THAN WHAT IS NECESSARY FOR NORMAL VEHICLE OPERATION. OVER TIME, THIS THINNER MATERIAL MAY RESULT IN A FATIGUE FAILURE OF THE REAR AXLE HOUSING, POSSIBLY IN THE LOCATION OF THE BRAKE FLANGE. Recall Details
Problem: NAVISTAR HAS NOTIFIED NHTSA ABOUT A DEFECT IN CERTAIN MODEL YEAR 2010 AND 2011 IC CE, HC, AND BE COMMERCIAL BUSES AND INTERNATIONAL 1300, 3200, 3300, 4100, 4200, 4300, 4400, AND MXT TRUCKS MANUFACTURED FROM NOVEMBER 19, 2003 THROUGH FEBRUARY 9, 2010. THE PARKING BRAKE MAY RELEASE IF THE BRAKE SYSTEM ELECTRONIC CONTROL UNIT (ECU) SOFTWARE MISINTERPRETS INPUT SIGNALS GENERATED FROM CYCLING THE IGNITION SWITCH MORE THAN ONCE AT A SPECIFIC FREQUENCY. Recall Details
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: ON CERTAIN TRUCKS, ONE OR BOTH REAR AXLE HOUSINGS MAY CONTAIN THINNER MATERIAL THAN WHAT IS NECESSARY FOR NORMAL VEHICLE OPERATION. OVER TIME, THIS THINNER MATERIAL MAY RESULT IN A FATIGUE FAILURE OF THE REAR AXLE HOUSING, POSSIBLY IN THE LOCATION OF THE BRAKE FLANGE. Recall Details
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: ON CERTAIN 4X2 MEDIUM DUTY TRUCKS, A LONGER FRONT HYDRAULIC BRAKE HOSE WAS SUBSTITUTED FOR THE SHORTER, CORRECT LENGTH HOSE. Recall Details
Problem: CERTAIN MY 2005 THROUGH 2006 INTERNATIONAL HEAVY TRUCKS AND IC CORP CE SCHOOL BUSES MANUFACTURED BETWEEN JUNE 4, 2004, AND MARCH 31, 2005. THE ANCHOR BOLT THAT IS THE PIVOT POINT FOR THE DRIVELINE PARKING BRAKE SHOES MAY FATIGUE AND BREAK AS A RESULT OF AN INCORRECT SURFACE TREATMENT. Recall Details
Problem: ON CERTAIN TRUCKS BUILT WITH IROS REAR AIR SUSPENSION SYSTEMS, FOUR REAR SUSPENSION FASTENERS MAY NOT BE TIGHTENED SUFFICIENTLY. THIS HARDWARE CONNECTS THE MAIN SUPPORT MEMBERS OF THE REAR SUSPENSION TO THE HANGER BRACKETS. Recall Details
Problem: CERTAIN MY 2005 THROUGH 2006 INTERNATIONAL HEAVY TRUCKS AND IC CORP CE SCHOOL BUSES MANUFACTURED BETWEEN JUNE 4, 2004, AND MARCH 31, 2005. THE ANCHOR BOLT THAT IS THE PIVOT POINT FOR THE DRIVELINE PARKING BRAKE SHOES MAY FATIGUE AND BREAK AS A RESULT OF AN INCORRECT SURFACE TREATMENT. Recall Details
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: CERTAIN TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." THE SEAT BELT LATCH FAILED A QUALITY REVIEW. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH V8 ENGINES AND AIR BRAKES OR AIR OPERATED PARK BRAKES, A STAND-OFF BRACKET WAS NOT INSTALLED. THE BRACKET SUPPORTS THE COPPER AIR COMPRESSOR DISCHARGE TUBE. NORMAL VEHICLE AND ENGINE VIBRATION CAN CAUSE THE UNSUPPORTED COPPER TUBE TO FAIL AT OR NEAR THE AIR COMPRESSOR CONNECTION. Recall Details
Problem: NAVISTAR IS RECALLING CERTAIN MODEL YEAR 2003 THROUGH 2010 INTERNATIONAL TRUCKS AND IC COMMERCIAL BUSES MANUFACTURED FROM DECEMBER 4, 2001 THROUGH DECEMBER 14, 2009 EQUIPPED WITH INTERNATIONAL VT365 ENGINES HAVING ENGINE CALIBRATION PAN2PVR0, PAN2PVR1, OR PAN2PWR. THE ENGINE NORMALLY RESPONDS TO A FAILED OPEN ACCELERATOR POSITION SENSOR CIRCUIT FAULT BY RETURNING THE ENGINE TO LOW IDLE SPEED OF 800 RPM AND DISABLING THE DRIVER'S ABILITY TO INCREASE THE ENGINE SPEED. HOWEVER IF THE OPEN CIRCUIT CORRECTS ITSELF WITHIN 30 SECONDS OF INITIATION, ENGINE SPEED COULD SUDDENLY INCREASE TO A HIGH IDLE SPEED OF 1200 RPM. Recall Details
Problem: ON CERTAIN MEDIUM AND HEAVY DUTY TRUCKS BUILT WITH DRIVELINE PARKING BRAKE CODES 04GAR, THE PARKING BRAKE ASSEMBLY MAY NOT HOLD THE VEHICLE IN POSITION WHEN SET. FACTORS CONTRIBUTING TO THIS POSSIBILITY ARE AS FOLLOWS: (1) CRACKED OR BROKEN CAMS; (2) LOOSE OR BROKEN ANCHOR BOLTS; (3) INITIAL SHOE DIAMETER NOT SET PROPERLY DURING ASSEMBLY, WHICH CAN LEAD TO PROGRESSIVE COMPONENT DAMAGE; (4) BENT ADJUSTER LEVERS THAT CANNOT FUNCTION; OR (5) AUTOMATIC ADJUSTER CABLES THAT ARE DISCONNECTED. Recall Details
Problem: CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH HYDRAULIC BRAKES AND AN AIR POWERED PARKING BRAKE (BRAKE CODE 04GAS) FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, "HYDRAULIC AND ELECTRIC BRAKE SYSTEMS." THE HYDRAULIC BRAKE MONITOR MODULE WAS NOT INSTALLED ON CERTAIN VEHICLES. Recall Details
Problem: ON CERTAIN TRUCKS, THE COTTER PIN THAT GOES THROUGH THE DRAG LINK BALL STUD AT THE CONNECTION TO THE PITMAN ARM IS MISSING. THIS PIN PREVENTS THE CASTLE NUT FROM LOOSENING. Recall Details
Problem: ON CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL VT365 ENGINES AND MANUFACTURED AT INTERNATIONAL DIESEL OF ALABAMA. THE INJECTOR DRIVER MODULES (IDM) BUILT FOR THE VT365 ENGINES COULD HAVE MISSING VIBRATION DAMPING/RETENTION SHELLS AND A MISSING HOT-MELT PROCESS ON THE DC/DC BOARDS. Recall Details
Problem: CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE PRIMARY AND SECONDARY AIR SUPPLY HOSES FROM THE FOOT VALVE TO THE PRIMARY AND SECONDARY AIR TANKS WERE IMPROPERLY ROUTED AT THE TANK. Recall Details
Problem: ON CERTAIN MEDIUM AND HEAVY DUTY TRUCKS BUILT WITH DRIVELINE PARKING BRAKE CODES 04GAR, THE PARKING BRAKE ASSEMBLY MAY NOT HOLD THE VEHICLE IN POSITION WHEN SET. FACTORS CONTRIBUTING TO THIS POSSIBILITY ARE AS FOLLOWS: (1) CRACKED OR BROKEN CAMS; (2) LOOSE OR BROKEN ANCHOR BOLTS; (3) INITIAL SHOE DIAMETER NOT SET PROPERLY DURING ASSEMBLY, WHICH CAN LEAD TO PROGRESSIVE COMPONENT DAMAGE; (4) BENT ADJUSTER LEVERS THAT CANNOT FUNCTION; OR (5) AUTOMATIC ADJUSTER CABLES THAT ARE DISCONNECTED. Recall Details
Problem: ON CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL VT365 ENGINES AND MANUFACTURED AT INTERNATIONAL DIESEL OF ALABAMA. THE INJECTOR DRIVER MODULES (IDM) BUILT FOR THE VT365 ENGINES COULD HAVE MISSING VIBRATION DAMPING/RETENTION SHELLS AND A MISSING HOT-MELT PROCESS ON THE DC/DC BOARDS. Recall Details
Problem: CERTAIN TRUCKS EQUIPPED WITH ENGINE STARTERS (CODE 08WWN OR 08WWP) BUILT BY LEECE-NEVILLE. THESE STARTERS HAVE A DEFECTIVE TERMINAL ADAPTER STUD. THE STUD IS USED ONLY AT THE POSITIVE BATTERY CONNECTION TO THE STARTER SOLENOID. IT WAS DESIGNED TO BE SCREWED ON OVER THE EXISTING STUD TO INCREASE THE STUD DIAMETER TO ACCOMMODATE THE LARGER SIZE OF THE POSITIVE BATTERY CABLE TERMINAL. THE ADAPTER STUD WAS WEAKENED WHEN THE HOLE WAS DRILLED TOO DEEP. Recall Details
Problem: ON CERTAIN TRUCKS, THE COTTER PIN THAT GOES THROUGH THE DRAG LINK BALL STUD AT THE CONNECTION TO THE PITMAN ARM IS MISSING. THIS PIN PREVENTS THE CASTLE NUT FROM LOOSENING. Recall Details
Problem: ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES. Recall Details
Problem: CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE PRIMARY AND SECONDARY AIR SUPPLY HOSES FROM THE FOOT VALVE TO THE PRIMARY AND SECONDARY AIR TANKS WERE IMPROPERLY ROUTED AT THE TANK. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH V8 ENGINES AND AIR BRAKES OR AIR OPERATED PARK BRAKES, A STAND-OFF BRACKET WAS NOT INSTALLED. THE BRACKET SUPPORTS THE COPPER AIR COMPRESSOR DISCHARGE TUBE. NORMAL VEHICLE AND ENGINE VIBRATION CAN CAUSE THE UNSUPPORTED COPPER TUBE TO FAIL AT OR NEAR THE AIR COMPRESSOR CONNECTION. Recall Details
Problem: ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES. Recall Details
Problem: CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE PRIMARY AND SECONDARY AIR SUPPLY HOSES FROM THE FOOT VALVE TO THE PRIMARY AND SECONDARY AIR TANKS WERE IMPROPERLY ROUTED AT THE TANK. Recall Details
Problem: ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES. Recall Details
Problem: ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES. Recall Details
Problem: ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES. Recall Details
Problem: ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES. Recall Details
|