by INTERNATIONAL TRUCK & ENGINE CORPORATION
NAVISTAR 9300 RECALLS - (14 Recalls Found)
Find your vehicle listed below. Results are sorted year from newest to oldest. Select the desired vehicle to view the complete details.
Information provided by the National Highway Traffic Safety Administration.
|
|
|
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH SPICER SPL170 55MM CENTER BERING PACKAGE. THE END YOKE RETAINING NUT CAN LOOSEN. Recall Details
Problem: VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY TRUCK CHASSIS EQUIPPED WITH 16,000 LB., 18,000 LB., OR 20,000 LB. HEAVY DUTY STEERING AXLES. THE INNER WHEEL BEARING CONE FOR THE STEERING AXLE WHEEL HUB ASSEMBLY DOES NOT PROPERLY FIT ONTO THE NAVISTAR STEERING AXLE SPINDLE ASSEMBLY. IMPROPER FIT OF THE BEARING TO THE SPINDLE INCREASES THE STRESS LEVELS TO THE STEERING AXLE SPINDLE WHICH COULD CAUSE SPINDLE FAILURE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH DANA/SPRAGUE WINDSHIELD WIPER ASSEMBLIES. THE KNURLED PIVOT SHAFT (WHICH OPERATES THE WINDSHIELD WIPER ARM) IS WELDED TO A LEVER, WHICH CONNECTS TO LINKAGE FROM THE WIPER MOTOR. THE WELD AT THE PIVOT SHAFT TO LEVER CAN FAIL. Recall Details
Problem: VEHICLE DESCRIPTION: TRUCKS ASSEMBLED WITH SKF LEVEL 2 TRUCK HUB UNITS (THU) RECEIVED FROM MERITOR. THESE HUBS CAN FATIGUE CRACK. Recall Details
Problem: VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY TRUCK CHASSIS EQUIPPED WITH 16,000 LB., 18,000 LB., OR 20,000 LB. HEAVY DUTY STEERING AXLES. THE INNER WHEEL BEARING CONE FOR THE STEERING AXLE WHEEL HUB ASSEMBLY DOES NOT PROPERLY FIT ONTO THE NAVISTAR STEERING AXLE SPINDLE ASSEMBLY. IMPROPER FIT OF THE BEARING TO THE SPINDLE INCREASES THE STRESS LEVELS TO THE STEERING AXLE SPINDLE WHICH COULD CAUSE SPINDLE FAILURE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH SPICER SPL170 55MM CENTER BERING PACKAGE. THE END YOKE RETAINING NUT CAN LOOSEN. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH PROSLEEPER BUNKS. A MICRO RELAY LOCATED BEHIND THE HVAC CONTROL PANEL IN THE BUNK CAN CORRODE FROM MOISTURE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH SPICER SPL170 55MM CENTER BERING PACKAGE. THE END YOKE RETAINING NUT CAN LOOSEN. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH SIX-SPOKE WHEEL ASSEMBLIES. THESE VEHICLES WERE MANUFACTURED WITH THE WRONG COMBINATIONS OF WHEEL ASSEMBLY PARTS. SHOULD THE SIX-SPOKE WHEEL ASSEMBLY HAVE MIS-MATCHED PARTS, HIGH STRESSES IN THE WHEEL STUDS AND POTENTIAL WHEEL FAILURES CAN OCCUR. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH ANTILOCK BRAKE SYSTEM (ABS). THE WIRING FROM THE ELECTRONIC CONTROL UNIT WAS CONNECTED TO THE WRONG WHEEL SENSOR. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH PROSLEEPER BUNKS. A MICRO RELAY LOCATED BEHIND THE HVAC CONTROL PANEL IN THE BUNK CAN CORRODE FROM MOISTURE. Recall Details
Problem: VEHICLE DESCRIPTION: TRUCKS ASSEMBLED WITH SKF LEVEL 2 TRUCK HUB UNITS (THU) RECEIVED FROM MERITOR. THESE HUBS CAN FATIGUE CRACK. Recall Details
Problem: VEHICLE DESCRIPTION: TRUCKS ASSEMBLED WITH SKF LEVEL 2 TRUCK HUB UNITS (THU) RECEIVED FROM MERITOR. THESE HUBS CAN FATIGUE CRACK. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH SIX-SPOKE WHEEL ASSEMBLIES. THESE VEHICLES WERE MANUFACTURED WITH THE WRONG COMBINATIONS OF WHEEL ASSEMBLY PARTS. SHOULD THE SIX-SPOKE WHEEL ASSEMBLY HAVE MIS-MATCHED PARTS, HIGH STRESSES IN THE WHEEL STUDS AND POTENTIAL WHEEL FAILURES CAN OCCUR. Recall Details
|