|
Problem: DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2011 FREIGHTLINER, FCCC, STERLING, AND WESTERN STAR HEAVY TRUCKS MANUFACTURED FROM SEPTEMBER 5, 2006, THROUGH JUNE 30, 2010, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2010 FREIGHTLINER BUSINESS CLASS M2, CUSTOM CHASSIS MT45, S2 CHASSIS, AND STERING ACTERRA VEHICLES MANUFACTURED FROM OCTOBER 5, 2006, THROUGH MAY 24, 2010, EQUIPPED WITH EPA 2007 MBE 900 DETROIT DIESEL ENGINES. ENGINE SOFTWARE MAY NOT REACT PROPERLY TO CERTAIN AFTERMARKET TREATMENT DEVICE FAULT CODES. THE SOFTWARE MAY UNNECESSARILY SHUTDOWN A VEHICLE OR MAY FAIL TO SHUTDOWN A VEHICLE WITH AN AFTERMARKET DEVICE OVER-TEMP FAULT. Recall Details
Problem: DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 FREIGHTLINER BUSINESS CLASS M2, STERLING ACTERRA, A-LINE, AND L-LINE HEAVY TRUCKS MANUFACTURED FROM SEPTEMBER 8, 2008 THROUGH APRIL 20, 2009 EQUIPPED WITH TRW IGEN3 INTERMEDIATE STEERING COLUMNS. THE WELD AROUND THE IGEN3 STEERING SHAFT TUBE THAT SECURES THE SPLINE TUBE TO THE INTERMEDIATE TUBE MAY BE MISLOCATED (I.E., NOT FULLY OVER THE SEAM CREATED WHEN THE TUBES ARE PRESSED TOGETHER.) Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2010 FREIGHTLINER M2, CUSTOM CHASSIS MT55, AND STERLING ACTERRA VEHICLES MANUFACTURED BETWEEN APRIL 4, 2007 AND JULY 15, 2009, EQUIPPED WITH CUMMINS ISC CM2150 AND ISL CM2150 MODEL DIESEL ENGINES. THE VEHICLES MAY BE DESIGNED WITH A HARD WIRED, DASH-MOUNTED SWITCH THAT ENABLES THE VEHICLE OPERATOR TO INHIBIT AFTERTREATMENT DIESEL PARTICULATE FILTER REGENERATION IN ENVIRONMENTS WHERE THE OPERATOR BELIEVES IT MAY BE UNSAFE FOR ELEVATED EXHAUST TEMPERATURES. DUE TO AN ISSUE WITH THE LOGIC IN THE ECM SOFTWARE IN THESE ENGINES, THE SWITCH MAY NOT FUNCTION CORRECTLY, LEADING THE OPERATOR TO BELIEVE THAT THE SWITCH IS IN "INHIBIT" MODE WHEN IT IS NOT. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2011 FREIGHTLINER, FCCC, STERLING, AND WESTERN STAR HEAVY TRUCKS MANUFACTURED FROM SEPTEMBER 5, 2006, THROUGH JUNE 30, 2010, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2011 FREIGHTLINER, FCCC, STERLING, AND WESTERN STAR HEAVY TRUCKS MANUFACTURED FROM SEPTEMBER 5, 2006, THROUGH JUNE 30, 2010, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2010 FREIGHTLINER M2, CUSTOM CHASSIS MT55, AND STERLING ACTERRA VEHICLES MANUFACTURED BETWEEN APRIL 4, 2007 AND JULY 15, 2009, EQUIPPED WITH CUMMINS ISC CM2150 AND ISL CM2150 MODEL DIESEL ENGINES. THE VEHICLES MAY BE DESIGNED WITH A HARD WIRED, DASH-MOUNTED SWITCH THAT ENABLES THE VEHICLE OPERATOR TO INHIBIT AFTERTREATMENT DIESEL PARTICULATE FILTER REGENERATION IN ENVIRONMENTS WHERE THE OPERATOR BELIEVES IT MAY BE UNSAFE FOR ELEVATED EXHAUST TEMPERATURES. DUE TO AN ISSUE WITH THE LOGIC IN THE ECM SOFTWARE IN THESE ENGINES, THE SWITCH MAY NOT FUNCTION CORRECTLY, LEADING THE OPERATOR TO BELIEVE THAT THE SWITCH IS IN "INHIBIT" MODE WHEN IT IS NOT. Recall Details
Problem: DAIMLER TRUCKS (DTNA) IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 FREIGHTLINER BUSINESS CLASS M2, STERLING ACTERRA, A-LINE, AND L-LINE HEAVY TRUCKS MANUFACTURED FROM SEPTEMBER 8, 2008 THROUGH APRIL 20, 2009 EQUIPPED WITH TRW IGEN3 INTERMEDIATE STEERING COLUMNS. THE WELD AROUND THE IGEN3 STEERING SHAFT TUBE THAT SECURES THE SPLINE TUBE TO THE INTERMEDIATE TUBE MAY BE MISLOCATED (I.E., NOT FULLY OVER THE SEAM CREATED WHEN THE TUBES ARE PRESSED TOGETHER.) Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2008 AND 2009 FREIGHTLINER BUSINESS CLASS M2 AND STERLING ACTERRA EMERGENCY VEHICLES MANUFACTURED FROM AUGUST 18, 2006, THROUGH JULY 7, 2010, EQUIPPED WITH EPA 2007 MBE 900 DETROIT DIESEL ENGINES. ENGINE SOFTWARE MAY NOT REACT PROPERLY TO CERTAIN AFTERMARKET TREATMENT DEVICE FAULT CODES. THE SOFTWARE MAY UNNECESSARILY SHUTDOWN A VEHICLE OR MAY FAIL TO SHUTDOWN A VEHICLE WITH AN AFTERMARKET DEVICE OVER-TEMP FAULT. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2010 FREIGHTLINER BUSINESS CLASS M2, CUSTOM CHASSIS MT45, S2 CHASSIS, AND STERING ACTERRA VEHICLES MANUFACTURED FROM OCTOBER 5, 2006, THROUGH MAY 24, 2010, EQUIPPED WITH EPA 2007 MBE 900 DETROIT DIESEL ENGINES. ENGINE SOFTWARE MAY NOT REACT PROPERLY TO CERTAIN AFTERMARKET TREATMENT DEVICE FAULT CODES. THE SOFTWARE MAY UNNECESSARILY SHUTDOWN A VEHICLE OR MAY FAIL TO SHUTDOWN A VEHICLE WITH AN AFTERMARKET DEVICE OVER-TEMP FAULT. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2010 FREIGHTLINER BUSINESS CLASS M2, CUSTOM CHASSIS MT45, S2 CHASSIS, AND STERING ACTERRA VEHICLES MANUFACTURED FROM OCTOBER 5, 2006, THROUGH MAY 24, 2010, EQUIPPED WITH EPA 2007 MBE 900 DETROIT DIESEL ENGINES. ENGINE SOFTWARE MAY NOT REACT PROPERLY TO CERTAIN AFTERMARKET TREATMENT DEVICE FAULT CODES. THE SOFTWARE MAY UNNECESSARILY SHUTDOWN A VEHICLE OR MAY FAIL TO SHUTDOWN A VEHICLE WITH AN AFTERMARKET DEVICE OVER-TEMP FAULT. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2008 AND 2009 FREIGHTLINER BUSINESS CLASS M2 AND STERLING ACTERRA EMERGENCY VEHICLES MANUFACTURED FROM AUGUST 18, 2006, THROUGH JULY 7, 2010, EQUIPPED WITH EPA 2007 MBE 900 DETROIT DIESEL ENGINES. ENGINE SOFTWARE MAY NOT REACT PROPERLY TO CERTAIN AFTERMARKET TREATMENT DEVICE FAULT CODES. THE SOFTWARE MAY UNNECESSARILY SHUTDOWN A VEHICLE OR MAY FAIL TO SHUTDOWN A VEHICLE WITH AN AFTERMARKET DEVICE OVER-TEMP FAULT. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2010 FREIGHTLINER M2, CUSTOM CHASSIS MT55, AND STERLING ACTERRA VEHICLES MANUFACTURED BETWEEN APRIL 4, 2007 AND JULY 15, 2009, EQUIPPED WITH CUMMINS ISC CM2150 AND ISL CM2150 MODEL DIESEL ENGINES. THE VEHICLES MAY BE DESIGNED WITH A HARD WIRED, DASH-MOUNTED SWITCH THAT ENABLES THE VEHICLE OPERATOR TO INHIBIT AFTERTREATMENT DIESEL PARTICULATE FILTER REGENERATION IN ENVIRONMENTS WHERE THE OPERATOR BELIEVES IT MAY BE UNSAFE FOR ELEVATED EXHAUST TEMPERATURES. DUE TO AN ISSUE WITH THE LOGIC IN THE ECM SOFTWARE IN THESE ENGINES, THE SWITCH MAY NOT FUNCTION CORRECTLY, LEADING THE OPERATOR TO BELIEVE THAT THE SWITCH IS IN "INHIBIT" MODE WHEN IT IS NOT. Recall Details
Problem: CUES, INC. IS RECALLING CERTAIN MODEL YEAR 2007-2009 SERVICE VEHICLES BUILT ON VARIOUS CHASSIS EQUIPPED WITH CARRIER AIRV CEILING UNITS, MODEL NOS. 68RV0010BA, 68RV0012CA, AND 68RV0010EA. THE HEATER ELEMENT IN THESE ASSEMBLIES MAY BE DEFECTIVE WHICH COULD CAUSE THE UNIT TO CREATE SMOKE OR SPARKS. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2011 FREIGHTLINER, FCCC, STERLING, AND WESTERN STAR HEAVY TRUCKS MANUFACTURED FROM SEPTEMBER 5, 2006, THROUGH JUNE 30, 2010, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH TUFTRAC REAR SUSPENSIONS, THE CENTER CASTING BRACKETS MAY BE OUT OF SPECIFICATION. AN OUT OF SQUARE CASTING MAY HAVE UNACCEPTABLE STRESS IN THE BRACKET WHEN IT IS INSTALLED AND MAY CAUSE IT TO CRACK IN SERVICE. Recall Details
Problem: ON CERTAIN TRUCKS BUILT WITH AXILOK REAR WHEEL SPINDLE NUTS, THE NUTS MAY HAVE BEEN IMPROPERLY INSTALLED, WITH ONE OR BOTH LOCKING CLIP TABS NOT PROPERLY ENGAGED OR DAMAGED. Recall Details
Problem: ON CERTAIN TRUCK-TRACTORS EQUIPPED WITH HOLLAND SIMPLEX SE OR SE II FIFTH WHEELS, THE LATCH LEVER PIVOT BOLT ASSEMBLY MAY HAVE BEEN OVER-TIGHTENED WHICH COULD DISTORT THE PIVOT BOLT SPACER SLEEVE. CORROSION OR CONTAMINATES IN THE PIVOT MAY CAUSE IT TO BIND AND PREVENT THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 900 MY 2008 FREIGHTLINER ARGOSY, ARGOSY RHD, CASCADIA, COLUMBIA, CENTURY ST, CORONADO, STERLING ACTERRA, L-LINE AND WESTERN STAR 4900 TRUCKS EQUIPPED WITH BENDIX MV-3 DASH CONTROL VALVES. THE MOLDED VALVE BODY HAS AN INCORRECT CORE PIN IN THE INJECTION MOLD CAUSING THE VALVE BODY TO BE OVERSIZED IN THE DOUBLE CHECK VALVE AREA. THIS CONDITION CAN ALLOW THE RUBBER DOUBLE CHECK VALVE TO BECOME LODGED IN THE BODY OPENING UNDER CERTAIN CIRCUMSTANCES. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Recall Details
Problem: FREIGHTLINER IS RECALLING CERTAIN SCHOOL BUS CHASSIS, HEAVY TRUCKS, VAN CHASSIS, RV MOTORHOME CHASSIS MANUFACTURED FROM JANUARY 5 TO MAY 17, 2007, EQUIPPED WITH AXLE ALLIANCE COMPANY (AAC) FRONT AXLES. DURING THE FRONT AXLE ASSEMBLY, THE FASTENERS THAT ATTACH THE STEERING ARM OR TIE ROD ARMS TO THE SPINDLE MAY BE OVER OR UNDER TIGHTENED. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH TUFTRAC REAR SUSPENSIONS, THE CENTER CASTING BRACKETS MAY BE OUT OF SPECIFICATION. AN OUT OF SQUARE CASTING MAY HAVE UNACCEPTABLE STRESS IN THE BRACKET WHEN IT IS INSTALLED AND MAY CAUSE IT TO CRACK IN SERVICE. Recall Details
Problem: FREIGHTLINER IS RECALLING CERTAIN SCHOOL BUS CHASSIS, HEAVY TRUCKS, VAN CHASSIS, RV MOTORHOME CHASSIS MANUFACTURED FROM JANUARY 5 TO MAY 17, 2007, EQUIPPED WITH AXLE ALLIANCE COMPANY (AAC) FRONT AXLES. DURING THE FRONT AXLE ASSEMBLY, THE FASTENERS THAT ATTACH THE STEERING ARM OR TIE ROD ARMS TO THE SPINDLE MAY BE OVER OR UNDER TIGHTENED. Recall Details
Problem: CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Recall Details
Problem: CERTAIN HEAVY TRUCKS, SHUTTLE BUSES, AND SCHOOL BUSES EQUIPPED WITH BENDIX MODULATED SPRING BRAKE VALVES. A DEFECT IN THE MODULATED SPRING BRAKE VALVE CASTING MAY CAUSE AN INTERMITTENT DELAY IN THE APPLICATION OF THE PARK BRAKE. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: Daimler Trucks North America LLC (DTNA) is recalling certain 2004-2019 Freightliner 108SD, 114SD, 122SD, Cascadia, Columbia, Classic, FL80, FLD 120SD, Business Class M2, Western Star 4700, 4900, 6900, Sterling Acterra, L7500, LT7500, L8500, LT8500, L9500, and LT9500 vehicles. The vehicles may have an insufficient service brake air reservoir capacity. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems." Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: ON CERTAIN TRUCK-TRACTORS EQUIPPED WITH HOLLAND SIMPLEX SE OR SE II FIFTH WHEELS, THE LATCH LEVER PIVOT BOLT ASSEMBLY MAY HAVE BEEN OVER-TIGHTENED WHICH COULD DISTORT THE PIVOT BOLT SPACER SLEEVE. CORROSION OR CONTAMINATES IN THE PIVOT MAY CAUSE IT TO BIND AND PREVENT THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Recall Details
Problem: ON CERTAIN TRUCKS BUILT WITH AXILOK REAR WHEEL SPINDLE NUTS, THE NUTS MAY HAVE BEEN IMPROPERLY INSTALLED, WITH ONE OR BOTH LOCKING CLIP TABS NOT PROPERLY ENGAGED OR DAMAGED. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2011 FREIGHTLINER, FCCC, STERLING, AND WESTERN STAR HEAVY TRUCKS MANUFACTURED FROM SEPTEMBER 5, 2006, THROUGH JUNE 30, 2010, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2010 FREIGHTLINER BUSINESS CLASS M2, CUSTOM CHASSIS MT45, S2 CHASSIS, AND STERING ACTERRA VEHICLES MANUFACTURED FROM OCTOBER 5, 2006, THROUGH MAY 24, 2010, EQUIPPED WITH EPA 2007 MBE 900 DETROIT DIESEL ENGINES. ENGINE SOFTWARE MAY NOT REACT PROPERLY TO CERTAIN AFTERMARKET TREATMENT DEVICE FAULT CODES. THE SOFTWARE MAY UNNECESSARILY SHUTDOWN A VEHICLE OR MAY FAIL TO SHUTDOWN A VEHICLE WITH AN AFTERMARKET DEVICE OVER-TEMP FAULT. Recall Details
Problem: ON CERTAIN TRUCK-TRACTORS EQUIPPED WITH HOLLAND SIMPLEX SE OR SE II FIFTH WHEELS, THE LATCH LEVER PIVOT BOLT ASSEMBLY MAY HAVE BEEN OVER-TIGHTENED WHICH COULD DISTORT THE PIVOT BOLT SPACER SLEEVE. CORROSION OR CONTAMINATES IN THE PIVOT MAY CAUSE IT TO BIND AND PREVENT THE FIFTH WHEEL JAW FROM LATCHING SECURELY AROUND THE TRAILER KING PIN. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA (DTNA) IS RECALLING 24,650 SCHOOL AND NON-SCHOOL BUSES, MOTOR HOME CHASSIS, AND TRUCKS MANUFACTURED FROM MARCH 9, 2004 THROUGH AUGUST 18, 2006, EQUIPPED WITH EPA04 CERTIFIED MBE900 ENGINES, MANUFACTURED BY DETROIT DIESEL BETWEEN MARCH 1, 2004, AND JULY 31, 2006. THE HIGH PRESSURE FUEL LINES AND TRANSFER TUBES MAY FATIGUE AND FRACTURE. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: Daimler Trucks North America LLC (DTNA) is recalling certain 2004-2019 Freightliner 108SD, 114SD, 122SD, Cascadia, Columbia, Classic, FL80, FLD 120SD, Business Class M2, Western Star 4700, 4900, 6900, Sterling Acterra, L7500, LT7500, L8500, LT8500, L9500, and LT9500 vehicles. The vehicles may have an insufficient service brake air reservoir capacity. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems." Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH VISTEON WINDSHIELD WIPERS, THE MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE APPLIED TO THE OUTPUT SHAFT GEAR. Recall Details
Problem: CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Recall Details
Problem: CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Recall Details
Problem: ON CERTAIN TRUCKS THE REAR HUB BEARINGS MAY HAVE BEEN INCORRECTLY ADJUSTED. Recall Details
Problem: Daimler Trucks North America LLC (DTNA) is recalling certain 2004-2019 Freightliner 108SD, 114SD, 122SD, Cascadia, Columbia, Classic, FL80, FLD 120SD, Business Class M2, Western Star 4700, 4900, 6900, Sterling Acterra, L7500, LT7500, L8500, LT8500, L9500, and LT9500 vehicles. The vehicles may have an insufficient service brake air reservoir capacity. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems." Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA (DTNA) IS RECALLING 24,650 SCHOOL AND NON-SCHOOL BUSES, MOTOR HOME CHASSIS, AND TRUCKS MANUFACTURED FROM MARCH 9, 2004 THROUGH AUGUST 18, 2006, EQUIPPED WITH EPA04 CERTIFIED MBE900 ENGINES, MANUFACTURED BY DETROIT DIESEL BETWEEN MARCH 1, 2004, AND JULY 31, 2006. THE HIGH PRESSURE FUEL LINES AND TRANSFER TUBES MAY FATIGUE AND FRACTURE. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2012 FREIGHTLINER M2, STERLING ACTERRA, 7500 & 8500, AND THOMAS BUILT HDX VEHICLES MANUFACTURED FROM JUNE 23, 2004, THROUGH MARCH 15, 2011, EQUIPPED WITH SPECIFIC MBE900 EPA04 AND EPA07 MODEL ENGINES. THE INTAKE AIR GRID HEATER MAY SHORT CIRCUIT AND FAIL DUE TO EXCESSIVE INTERNAL TEMPERATURES. Recall Details
Problem: DAIMLER TRUCKS NORTH AMERICA (DTNA) IS RECALLING 24,650 SCHOOL AND NON-SCHOOL BUSES, MOTOR HOME CHASSIS, AND TRUCKS MANUFACTURED FROM MARCH 9, 2004 THROUGH AUGUST 18, 2006, EQUIPPED WITH EPA04 CERTIFIED MBE900 ENGINES, MANUFACTURED BY DETROIT DIESEL BETWEEN MARCH 1, 2004, AND JULY 31, 2006. THE HIGH PRESSURE FUEL LINES AND TRANSFER TUBES MAY FATIGUE AND FRACTURE. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: ON CERTAIN TRUCKS AND FIRE TRUCKS EQUIPPED WITH KYS 4735-43782-02 ENGINE COOLING FANS AND BUILT ON CATERPILLAR 3126, C7, MBE906, MBE926, OR CUMMINS ISC ENGINES, THE STEEL FAN INSERT ON THE COOLING FANS CAN CRACK. Recall Details
Problem: CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Recall Details
Problem: CERTAIN MICHELIN XDE COMMERCIAL TRUCK TIRES, SIZE 10R22.5 LRG AND LRF FOR USE ON FREIGHTLINER SCHOOL AND TRANSIT BUSES. THESE TIRES WERE MANFACTURED BETWEEN MAY 23 AND OCTOBER 24, 2004, CAN EXPERIENCE RAPID AIR LOSS DUE TO AN IRREGULARITY OF THE INNER LINER. Recall Details
Problem: ON CERTAIN TRUCKS THE REAR HUB BEARINGS MAY HAVE BEEN INCORRECTLY ADJUSTED. Recall Details
Problem: ON CERTAIN TRUCKS BUILT WITH 8,000 OR 6,000 POUND FRONT AXLES AND FOUR-PIECE SPINDLE NUT SETS, PREMATURE FRONT ,WHEEL BEARING WEAR MAY BE CAUSED BY INCONSISTENT BEARING ENDPLAY ADJUSTMENT. Recall Details
Problem: CERTAIN FREIGHTLINER SCHOOL BUS CHASSIS, HEAVY TRUCKS, AND THOMAS BUILT SCHOOL BUSES MANUFACTURED BETWEEN JULY 2002 AND JULY 3, 2007, EQUIPPED WITH BENDIX SR-7 SPRING BRAKE CONTROL VALVES. THE PARKER SCV BRASS 90 DEGREE SINGLE CHECK VALVES (SCV) WHICH ATTACH TO THE SUPPLY PORT OF A BENDIX SR-7 SPRING BRAKE MODULATING VALVE CAN BREAK APART. PIECES OF THE PARKER SCV CAN BECOME LODGED INSIDE THE SR-7 SPRING BRAKE MODULATING VALVE, POTENTIALLY CAUSING EITHER LEAKAGE OUT OF THE SR-7 VALVE OR PREVENTING AIR FROM PROPERLY EXHAUSTING FROM THE SR-7 VALVE. ALSO, DUE TO A MANUFACTURING DEFECT IN THE INTERNAL RUBBER CHECK VALVE INSIDE THE SR-7 SPRING BRAKE MODULATING VALVES, THE VALVES CAN BECOME DEFORMED AND NOT SEAT PROPERLY. Recall Details
Problem: ON CERTAIN TRUCKS AND FIRE TRUCKS EQUIPPED WITH KYS 4735-43782-02 ENGINE COOLING FANS AND BUILT ON CATERPILLAR 3126, C7, MBE906, MBE926, OR CUMMINS ISC ENGINES, THE STEEL FAN INSERT ON THE COOLING FANS CAN CRACK. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: ON CERTAIN TRUCKS AND FIRE TRUCKS EQUIPPED WITH KYS 4735-43782-02 ENGINE COOLING FANS AND BUILT ON CATERPILLAR 3126, C7, MBE906, MBE926, OR CUMMINS ISC ENGINES, THE STEEL FAN INSERT ON THE COOLING FANS CAN CRACK. Recall Details
Problem: ON CERTAIN TRUCKS BUILT WITH 8,000 OR 6,000 POUND FRONT AXLES AND FOUR-PIECE SPINDLE NUT SETS, PREMATURE FRONT ,WHEEL BEARING WEAR MAY BE CAUSED BY INCONSISTENT BEARING ENDPLAY ADJUSTMENT. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH CATERPILLAR 3126E HYDRAULICALLY CONTROLLED ELECTRONICALLY ACTUATED UNIT INJECTED DIESEL ENGINES WITH HIGH EFFICIENCY PUMPS (HEP8), THE PUMP COMPONENTS MAY EXPERIENCE A HIGH PRESSURE SEAL FAILURE WHICH CAN RESULT IN A SHORT PERIOD OF ROUGH RUNNING AND SUBSEQUENT ENGINE STALL DUE TO A LOSS OF INJECTION ACTUATION PRESSURE. Recall Details
Problem: ON CERTAIN HEAVY TRUCKS, THE CAST OUTPUT YOKE ON THE MERCEDES-BENZ TRANSMISSIONS COULD FRACTURE ON VEHICLE WITH 1610 OR 16T SERIES DRIVELINES. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: VEHICLE DESCRIPTION: VEHICLES EQUIPPED WITH CERTAIN HALDEX BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED. Recall Details
Problem: ON CERTAIN TRUCKS, THE WELDS THAT ATTACH THE REAR SUSPENSION CONTROL ROD BRACKETS TO THE AXLE HOUSING MAY NOT MEET SPECIFICATIONS. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH MERITOR WABCO PNEUMATIC ANITLOCK BRAKE SYSTEM (ABS) VALVE PACKAGES, THE ASSEMBLY BOLTS ON THESE VALVE PACKAGES WERE NOT TIGHTENED CORRECTLY. Recall Details
Problem: ON CERTAIN TRUCKS, A CAPACITOR IN THE POWER LINE CONTROL (PLC) FILTER COULD OVERHEAT AND/OR IGNITE WHEN SUBJECTED TO REVERSE POLARITY ELECTRICAL SPIKES. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH HYDRAULIC BRAKES AND A DURAPARK PARK BRAKE SYSTEM MANUFACTURED BY ARVINMERITOR. AIR IS ENTERING THE HYDRAULIC REAR BRAKE CYLINDERS THROUGH AN UNKNOWN PATH AND THE REAR SELF-ADJUSTING BRAKES MAY NOT BE OPERATING PROPERLY. Recall Details
Problem: ON CERTAIN HEAVY TRUCKS, THE CAST OUTPUT YOKE ON THE MERCEDES-BENZ TRANSMISSIONS COULD FRACTURE ON VEHICLE WITH 1610 OR 16T SERIES DRIVELINES. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Recall Details
Problem: ON CERTAIN TRUCKS BUILT WITH 8,000 OR 6,000 POUND FRONT AXLES AND FOUR-PIECE SPINDLE NUT SETS, PREMATURE FRONT ,WHEEL BEARING WEAR MAY BE CAUSED BY INCONSISTENT BEARING ENDPLAY ADJUSTMENT. Recall Details
Problem: ON CERTAIN TRUCKS AND FIRE TRUCKS EQUIPPED WITH KYS 4735-43782-02 ENGINE COOLING FANS AND BUILT ON CATERPILLAR 3126, C7, MBE906, MBE926, OR CUMMINS ISC ENGINES, THE STEEL FAN INSERT ON THE COOLING FANS CAN CRACK. Recall Details
Problem: DAIMLER TRUCKS IS RECALLING 28,764 MY 2001 THROUGH 2008 FCCC B2 AND FS65 SCHOOL BUS CHASSIS, FCCC FB65 CONVENTIONAL BUSES, AND STERLING ACTERRA, FREIGHTLINER FLN, AND BUSINESS CLASS M2 HEAVY TRUCKS, BUILT FROM JANUARY 26, 2000, THROUGH MARCH 24, 2008, MANUFACTURED WITH ARVINMERITOR OR AXLE ALLIANCE COMPANY 6,000 THROUGH 8,000 POUND FRONT AXLES UTILIZING A FOUR PIECE SPINDLE-NUT SET. THESE AXLE ASSEMBLIES MAY HAVE BEEN PRODUCED WITH A THIN SPINDLE NUT WHICH MAY LEAD TO INCORRECT END PLAY, CONE SPIN, EXCESSIVE HEAT, DEGRADATION OF LUBRICATION, WEAR OF THE SPINDLE NUT AND BEARING JOURNAL, OIL CONTAMINATION WITH METAL SHAVINGS, AND PREMATURE BEARING FAILURE. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Recall Details
Problem: ON CERTAIN TRUCKS BUILT WITH 8,000 OR 6,000 POUND FRONT AXLES AND FOUR-PIECE SPINDLE NUT SETS, PREMATURE FRONT ,WHEEL BEARING WEAR MAY BE CAUSED BY INCONSISTENT BEARING ENDPLAY ADJUSTMENT. Recall Details
Problem: ON CERTAIN HEAVY TRUCKS, THE CAST OUTPUT YOKE ON THE MERCEDES-BENZ TRANSMISSIONS COULD FRACTURE ON VEHICLE WITH 1610 OR 16T SERIES DRIVELINES. Recall Details
Problem: VEHICLE DESCRIPTION: VEHICLES EQUIPPED WITH CERTAIN HALDEX BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE UPPER STEERING COLUMN PINCH BOLT MAY NOT HAVE BEEN PROPERLY TORQUED. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS AND SCHOOL BUS CHASSIS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH ARVINMERITOR MFS-8 SERIES FRONT AXLE ASSEMBLIES. THE WHEEL BEARING NUT ADJUSTMENT ASSEMBLY MAY 1) RESTRICT A COMPLETE LUBRICATION FILL AT ASSEMBLY AND/OR 2) SHEAR THE SPINDLE PERFORATED WASHER'S LOCKING TAB (LOCATED IN THE INSIDE DIAMETER OF THE WASHER) WHEN TIGHTENED. IF THE WASHER TAB IS SHEARED, TIGHTENING OF THE OUTER SPINDLE NUT MAY CAUSE THE BEARINGS TO BE EXCESSIVELY PRELOADED RATHER THAN THE INTENDED .001" - .005" END PLAY. EITHER OF THESE CONDITIONS MAY CAUSE PREMATURE WHEEL BEARING FAILURE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS, SHUTTLE BUSES, TRANSIT BUSES AND STEP VANS EQUIPPED WITH ALLISON 1000 OR 2400 SERIES TRANSMISSIONS. THESE TRANSMISSIONS CAN EXPERIENCE PARK PAWL TO REAR COVER INTERFERENCE DUE TO AN OUT OF FLATNESS CONDITION. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH ACCURIDE 22.5 X 8.25 15 TUBELESS DEMOUNTABLE RIMS, PART NO. 32051. CERTAIN RIMS CONTAIN A NON-FUSION AREA IN THE BUTT-WELD OF THE MOUNTING RING. UNDER CERTAIN CIRCUMSTANCES, THE DEFECT COULD DEVELOP INTO A CRACK ON THE MOUNTING RING. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. A SUPPORT CLAMP WAS OMITTED FROM THE FRONT AXLE HYDRAULIC BRAKE LINE FROM THE CHASSIS TO THE BRAKE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. INCORRECT WIRING OF THE INSTRUMENT LIGHTING DIMMER SWITCH CAN CAUSE IT TO FAIL. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. AN UNDERSIZED GROUND WIRE FOR THE DEFROSTER BLOWER MOTOR SWITCH CAN CAUSE THE SWITCH TO OVERHEAT AND FAIL. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CHALMERS 1000 AND 800 SERIES SUSPENSION KITS. THESE SUSPENSION KITS MAY HAVE INSUFFICIENT PENETRATION OF THE WELD ATTACHING THE TORQUE ROD EYE TO THE TORQUE ROD TUBE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH HYDRAULIC BRAKES AND A DURAPARK PARK BRAKE SYSTEM MANUFACTURED BY ARVINMERITOR. AIR IS ENTERING THE HYDRAULIC REAR BRAKE CYLINDERS THROUGH AN UNKNOWN PATH AND THE REAR SELF-ADJUSTING BRAKES MAY NOT BE OPERATING PROPERLY. Recall Details
Problem: ON CERTAIN TRUCKS, THE WELDS THAT ATTACH THE REAR SUSPENSION CONTROL ROD BRACKETS TO THE AXLE HOUSING MAY NOT MEET SPECIFICATIONS. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: ON CERTAIN TRUCKS, THE WELDS THAT ATTACH THE REAR SUSPENSION CONTROL ROD BRACKETS TO THE AXLE HOUSING MAY NOT MEET SPECIFICATIONS. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THE UPPER STEERING COLUMN PINCH BOLT MAY NOT HAVE BEEN PROPERLY TORQUED. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS AND SCHOOL BUS CHASSIS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH HYDRAULIC BRAKES AND A DURAPARK PARK BRAKE SYSTEM MANUFACTURED BY ARVINMERITOR. AIR IS ENTERING THE HYDRAULIC REAR BRAKE CYLINDERS THROUGH AN UNKNOWN PATH AND THE REAR SELF-ADJUSTING BRAKES MAY NOT BE OPERATING PROPERLY. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS AND SCHOOL BUS CHASSIS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH HYDRAULIC BRAKES AND A DURAPARK PARK BRAKE SYSTEM MANUFACTURED BY ARVINMERITOR. AIR IS ENTERING THE HYDRAULIC REAR BRAKE CYLINDERS THROUGH AN UNKNOWN PATH AND THE REAR SELF-ADJUSTING BRAKES MAY NOT BE OPERATING PROPERLY. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS AND SCHOOL BUS CHASSIS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MERITOR BRAND 12" X 4" DCM DRUM PARKING BRAKE, THE BOLTS USED TO ATTACH THE PARKING BRAKE ASSEMBLY TO THE FLANGE YOKE ARE TOO LARGE AND CAN INTERFERE WITH THE PROPER ENGAGEMENT OF THE BRAKING SYSTEM AND POSSIBLY DISENGAGE. Recall Details
|