|
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2021-2022 VAH, VDH, VNL, AND VNR vehicles. The hubcap compression spring can cause the hubcap to separate. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2021-2022 VAH, VDH, VNL, AND VNR vehicles. The hubcap compression spring can cause the hubcap to separate. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2020-2021 VAH, VHD, VNL and VNR vehicles. The die cast pedal plate may break at one of its attachment points, possibly resulting in the brake pedal dislodging. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems." Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling 2021 VNL, VNR, VAH, and VHD vehicles. The collets (internal jaws) for the brass fitting inserts used in the pneumatic pass-through plate may have been damaged during leak testing. As a result, the brass fitting may completely release the air brake line from the pass-through plate while under pressure. If this occurs on the park brake circuit, signal pressure that holds off the mechanical spring in the park brake chambers will be lost allowing the park brakes to apply. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2021-2022 VAH, VDH, VNL, AND VNR vehicles. The hubcap compression spring can cause the hubcap to separate. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2021-2022 VAH, VDH, VNL, AND VNR vehicles. The hubcap compression spring can cause the hubcap to separate. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2021 VNL, VHD, and VNR vehicles. The king pin nut may not have been installed or properly tightened during axle assembly. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2020-2021 VAH, VHD, VNL and VNR vehicles. The die cast pedal plate may break at one of its attachment points, possibly resulting in the brake pedal dislodging. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems." Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2018-2020 VAH, VHD, VNL, and VNR vehicles. The fuse in the transmission circuit may blow, preventing the transmission from shifting. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2019-2020 VAH, VHD, VNL, and VNR vehicles. The t-bolt clasps on the transmission auxiliary air tank straps may have been over-tightened, resulting in potential deformation to the strap where the t-bolt is anchored. Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2019-2020 VAH, VHD, VNL, and VNR vehicles. The t-bolt clasps on the transmission auxiliary air tank straps may have been over-tightened, resulting in potential deformation to the strap where the t-bolt is anchored. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2019 Volvo VNL and VHD trucks, equipped with Bridgestone M854 tires with date codes 2418-2518, Bridgestone M860A tires with date code 2518, and Bridgestone M864 tires with date codes 2318-2418, all of size 425/65R22.5. The sidewall steel body cords may be exposed, possibly causing unexpected, rapid air loss during use. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 119, "New Pneumatic Tires - Other than Passenger Cars." Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2018-2020 VAH, VHD, VNL, and VNR vehicles. The fuse in the transmission circuit may blow, preventing the transmission from shifting. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo Trucks) is recalling certain 2018-2020 VAH, VHD, VNL, and VNR vehicles. The fuse in the transmission circuit may blow, preventing the transmission from shifting. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2017 Volvo VHD, VNL, and VNM trucks manufactured February 19, 2016, to June 21, 2016. The affected vehicles were built with front wheel hubs that cannot support the gross axle weight rating of the front axle. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2015-2017 VHD trucks. The Gross Axle Weight Rating (GAWR) for the pusher or tag axle may be incorrect on the certification label. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2015-2017 VHD trucks. The Gross Axle Weight Rating (GAWR) for the pusher or tag axle may be incorrect on the certification label. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2015-2016 VAH and VHD trucks manufactured April 1, 2014, to August 14, 2015. The affected vehicles may be equipped with headlights that do not meet the minimum intensity requirements, resulting in insufficient illumination of the roadway. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2012, 2014-2015 VHD, 2012-2015 VNL, and 2014-2015 VNM trucks manufactured June 16, 2011, to August 18, 2014, and equipped with the Eco-Roll option. The affected trucks may fail to re-engage the vehicle drivetrain after using the Eco-Roll feature. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2015-2016 VAH and VHD trucks manufactured April 1, 2014, to August 14, 2015. The affected vehicles may be equipped with headlights that do not meet the minimum intensity requirements, resulting in insufficient illumination of the roadway. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2015-2017 VHD trucks. The Gross Axle Weight Rating (GAWR) for the pusher or tag axle may be incorrect on the certification label. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2014 VAH, VHD, VNL, and VNM trucks manufactured August 12, 2013, through November 14, 2013; and equipped with IMMI-brand L9 seat belt buckles. When the button is pressed to release the seat belt, the latch plate can become partially engaged with the buckle, making the seat belt difficult to unlatch. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 209, "Seat Belt Assemblies." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2012, 2014-2015 VHD, 2012-2015 VNL, and 2014-2015 VNM trucks manufactured June 16, 2011, to August 18, 2014, and equipped with the Eco-Roll option. The affected trucks may fail to re-engage the vehicle drivetrain after using the Eco-Roll feature. Recall Details
Problem: Volvo is recalling certain model year 2012-2014 VHD, VNL, and VNM trucks, manufactured from April 18, 2011, through March 14, 2013, and equipped with a horizontally mounted remote battery disconnect switch. The remote battery disconnect switch was manufactured with incorrect hardware allowing the cables to loosen. Additionally, as mounted, the cables may vibrate and chafe. Recall Details
Problem: Volvo is recalling certain model year 2012-2014 VHD, VNL, and VNM trucks, manufactured from April 18, 2011, through March 14, 2013, and equipped with a horizontally mounted remote battery disconnect switch. The remote battery disconnect switch was manufactured with incorrect hardware allowing the cables to loosen. Additionally, as mounted, the cables may vibrate and chafe. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo is recalling certain model year 2012-2014 VHD, VNL, and VNM trucks, manufactured from April 18, 2011, through March 14, 2013, and equipped with a horizontally mounted remote battery disconnect switch. The remote battery disconnect switch was manufactured with incorrect hardware allowing the cables to loosen. Additionally, as mounted, the cables may vibrate and chafe. Recall Details
Problem: Volvo is recalling certain model year 2012-2014 VHD, VNL, and VNM trucks, manufactured from April 18, 2011, through March 14, 2013, and equipped with a horizontally mounted remote battery disconnect switch. The remote battery disconnect switch was manufactured with incorrect hardware allowing the cables to loosen. Additionally, as mounted, the cables may vibrate and chafe. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2011-2013 VHD and VNL vehicles manufactured December 13, 2010, through July 17, 2012. These vehicles are equipped with an MGM Type 24 J-series piston parking brake chamber. The brake chambers may leak pressure allowing the parking brake to drag when it is supposed to be released. Brake dragging could lead to overheated brake components. Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2011-2012 VAH, VHD, VNL, and VNM trucks manufactured February 1, 2010, through September 30, 2010 and June 1, 2011, through November 30, 2011. The windshield wiper motor may fail. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2012, 2014-2015 VHD, 2012-2015 VNL, and 2014-2015 VNM trucks manufactured June 16, 2011, to August 18, 2014, and equipped with the Eco-Roll option. The affected trucks may fail to re-engage the vehicle drivetrain after using the Eco-Roll feature. Recall Details
Problem: Volvo is recalling certain model year 2012-2014 VHD, VNL, and VNM trucks, manufactured from April 18, 2011, through March 14, 2013, and equipped with a horizontally mounted remote battery disconnect switch. The remote battery disconnect switch was manufactured with incorrect hardware allowing the cables to loosen. Additionally, as mounted, the cables may vibrate and chafe. Recall Details
Problem: Volvo is recalling certain model year 2012-2014 VHD, VNL, and VNM trucks, manufactured from April 18, 2011, through March 14, 2013, and equipped with a horizontally mounted remote battery disconnect switch. The remote battery disconnect switch was manufactured with incorrect hardware allowing the cables to loosen. Additionally, as mounted, the cables may vibrate and chafe. Recall Details
Problem: VOLVO TRUCKS IS RECALLING CERTAIN MODEL YEAR 2011-2012 VHD, VNL, AND MODEL YEAR 2012 VNM TRUCKS MANUFACTURED FROM OCTOBER 15, 2010, THROUGH JANUARY 31, 2011, AND EQUIPPED WITH GUNITE AUTOMATIC SLACK ADJUSTERS. DUE TO AN INCOMPLETE "KNITTING" OF THE IRON AT THE TIME OF CASTING, INADEQUATE STRUCTURAL INTEGRITY OF THE SLACK ADJUSTER HOUSING CAN OCCUR, WHICH COULD CAUSE THE HOUSING TO BREAK AT THE HANDLE UNDER NORMAL OPERATING LOADS. Recall Details
Problem: VOLVO TRUCKS IS RECALLING CERTAIN MODEL YEAR 2012 VHD, VNL, AND VNM TRUCKS EQUIPPED WITH A MERITOR DRIVELINE. THE TUBING USED TO ASSEMBLE THE DRIVELINES HAS A NONCONFORMING SEAM WELD WITH INSUFFICIENT BONDING OF THE MATERIAL. Recall Details
Problem: VOLVO IS RECALLING CERTAIN MODEL YEAR 2011-2012 VHD AND MODEL YEAR 2011-2013 VNL AND VNM VEHICLES, MANUFACTURED FROM DECEMBER 2, 2010, THROUGH JANUARY 18, 2012, AND EQUIPPED WITH BENDIX ATR-6 TRACTION RELAY VALVES. IN EXTREMELY COLD CONDITIONS, THESE BENDIX RELAY VALVES MAY POTENTIALLY DEVELOP INTERNAL LEAKAGE. INTERNAL LEAKAGE CAN LEAD TO AIR PRESSURE BEING DELIVERED TO AFFECTED PRIMARY OR SECONDARY BRAKE CAUSING CONTINUOUS BRAKE APPLICATION. Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2011-2013 VHD and VNL vehicles manufactured December 13, 2010, through July 17, 2012. These vehicles are equipped with an MGM Type 24 J-series piston parking brake chamber. The brake chambers may leak pressure allowing the parking brake to drag when it is supposed to be released. Brake dragging could lead to overheated brake components. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2011-2012 VAH, VHD, VNL, and VNM trucks manufactured February 1, 2010, through September 30, 2010 and June 1, 2011, through November 30, 2011. The windshield wiper motor may fail. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2011-2013 VHD and VNL vehicles manufactured December 13, 2010, through July 17, 2012. These vehicles are equipped with an MGM Type 24 J-series piston parking brake chamber. The brake chambers may leak pressure allowing the parking brake to drag when it is supposed to be released. Brake dragging could lead to overheated brake components. Recall Details
Problem: VOLVO IS RECALLING CERTAIN MODEL YEAR 2011-2012 VHD AND MODEL YEAR 2011-2013 VNL AND VNM VEHICLES, MANUFACTURED FROM DECEMBER 2, 2010, THROUGH JANUARY 18, 2012, AND EQUIPPED WITH BENDIX ATR-6 TRACTION RELAY VALVES. IN EXTREMELY COLD CONDITIONS, THESE BENDIX RELAY VALVES MAY POTENTIALLY DEVELOP INTERNAL LEAKAGE. INTERNAL LEAKAGE CAN LEAD TO AIR PRESSURE BEING DELIVERED TO AFFECTED PRIMARY OR SECONDARY BRAKE CAUSING CONTINUOUS BRAKE APPLICATION. Recall Details
Problem: VOLVO TRUCKS IS RECALLING CERTAIN MODEL YEAR 2011-2012 VHD, VNL, AND MODEL YEAR 2012 VNM TRUCKS MANUFACTURED FROM OCTOBER 15, 2010, THROUGH JANUARY 31, 2011, AND EQUIPPED WITH GUNITE AUTOMATIC SLACK ADJUSTERS. DUE TO AN INCOMPLETE "KNITTING" OF THE IRON AT THE TIME OF CASTING, INADEQUATE STRUCTURAL INTEGRITY OF THE SLACK ADJUSTER HOUSING CAN OCCUR, WHICH COULD CAUSE THE HOUSING TO BREAK AT THE HANDLE UNDER NORMAL OPERATING LOADS. Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: VOLVO IS RECALLING CERTAIN MODEL YEAR 2008-2011 VHD, VNL, VNM, AS WELL AS 2008-2010 VT VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF PART 567, "CERTIFICATION." THE TIRE DESCRIPTION MAY BE INCORRECT ON THE VEHICLE'S CERTIFICATION LABEL. Recall Details
Problem: VOLVO IS RECALLING CERTAIN MODEL YEAR 2008-2011 VHD, VNL, VNM, AS WELL AS 2008-2010 VT VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF PART 567, "CERTIFICATION." THE TIRE DESCRIPTION MAY BE INCORRECT ON THE VEHICLE'S CERTIFICATION LABEL. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2009-2016 VHD trucks manufactured from April 7, 2008, through December 9, 2015, equipped with USK non-greasable drag links. The ball joint seals may be compromised, which can allow water and other contaminants to enter the ball joints. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: VOLVO TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 AND 2009 VHD, MODEL YEAR 2006 THROUGH 2010 VN, AND MODEL YEAR 2007 THROUGH 2009 VT TRUCKS MANUFACTURED FROM NOVEMBER 7, 2005, THROUGH OCTOBER 30, 2009, EQUIPPED WITH AN AIR RELEASE FIFTH WHEEL. THE INVERSION VALVE ON THE FRAME MAY BE ORIENTATED WHERE CONTAMINANTS CAN ENTER THE VALVE THROUGH THE EXHAUST PORT. AS A RESULT, THE BRAKE VALVE MAY CORRODE. Recall Details
Problem: VOLVO IS RECALLING CERTAIN MODEL YEAR 2008-2011 VHD, VNL, VNM, AS WELL AS 2008-2010 VT VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF PART 567, "CERTIFICATION." THE TIRE DESCRIPTION MAY BE INCORRECT ON THE VEHICLE'S CERTIFICATION LABEL. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: VOLVO IS RECALLING CERTAIN MODEL YEAR 2008-2011 VHD, VNL, VNM, AS WELL AS 2008-2010 VT VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF PART 567, "CERTIFICATION." THE TIRE DESCRIPTION MAY BE INCORRECT ON THE VEHICLE'S CERTIFICATION LABEL. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Recall Details
Problem: ON CERTAIN TRUCKS, THE NUT USED TO RETAIN THE STEERING SHAFT MAY OR MAY NOT BE A LOCK NUT THAT HAS THE LOCKING FEATURE. A LOCK NUT IS REQUIRED TO PROVIDE ADDITIONAL RESISTANCE TO ENSURE THAT THE NUT DOES NOT COME LOOSE. Recall Details
Problem: ON CERTAIN TRUCKS, AN UNPROTECTED LEAD IN THE THERMOSWITCH OF THE HEATER MAY MAKE CONTACT WITH ANOTHER POST POSSIBLY CREATING A SHORT CIRCUIT, WHICH CAN RESULT IN CONTINUOUS OPERATION OF THE HEATING ELEMENT. Recall Details
Problem: ON CERTAIN TRUCKS, THE HOOD RESTRAINT CYLINDER DOES NOT CONTAIN ENOUGH DAMPENING TO ADEQUATELY RESTRAIN THE HOOD. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH A SAF HOLLAND SIMPLEX FIFTH WHEEL, THE LEVER ARM PIVOT BOLT MAY HAVE BEEN OVER TIGHTENED. AN OVER TIGHTENED PIVOT BOLT CAN DISTORT THE PIVOT BOLT SPACER SLEEVE, WHICH MAY PREVENT THE FIFTH WHEEL LATCH JAW FROM CLOSING AND LATCHING SECURELY AROUND THE TRAILER KING PIN. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain model year 2007-2014 VAH, VHD, VNL, VNM, and VT models. The affected vehicles were built without a redundant clutch disengagement switch. Without a redundant switch, a loss of signal from the brake air pressure switch can prevent the clutch from automatically disengaging when the brake is applied. Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH A SAF HOLLAND SIMPLEX FIFTH WHEEL, THE LEVER ARM PIVOT BOLT MAY HAVE BEEN OVER TIGHTENED. AN OVER TIGHTENED PIVOT BOLT CAN DISTORT THE PIVOT BOLT SPACER SLEEVE, WHICH MAY PREVENT THE FIFTH WHEEL LATCH JAW FROM CLOSING AND LATCHING SECURELY AROUND THE TRAILER KING PIN. Recall Details
Problem: ON CERTAIN TRUCKS, THE NUT USED TO RETAIN THE STEERING SHAFT MAY OR MAY NOT BE A LOCK NUT THAT HAS THE LOCKING FEATURE. A LOCK NUT IS REQUIRED TO PROVIDE ADDITIONAL RESISTANCE TO ENSURE THAT THE NUT DOES NOT COME LOOSE. Recall Details
Problem: ON CERTAIN TRUCKS, AN UNPROTECTED LEAD IN THE THERMOSWITCH OF THE HEATER MAY MAKE CONTACT WITH ANOTHER POST POSSIBLY CREATING A SHORT CIRCUIT, WHICH CAN RESULT IN CONTINUOUS OPERATION OF THE HEATING ELEMENT. Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH DANA STEERING SHAFTS, THERE IS A POTENTIAL THAT THE STEERING SHAFT PINCH BOLT HOLE MAY BE INCORRECTLY LOCATED. THE PINCH BOLT FITS INTO A GROOVE IN THE STEERING GEAR INPUT SHAFT TO ENSURE THAT THE STEERING SHAFT DOES NOT SEPARATE FROM THE STEERING GEAR IF THE PINCH BOLT COMES LOOSE. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: VOLVO TRUCKS IS RECALLING CERTAIN MODEL YEAR 2007 AND 2009 VHD, MODEL YEAR 2006 THROUGH 2010 VN, AND MODEL YEAR 2007 THROUGH 2009 VT TRUCKS MANUFACTURED FROM NOVEMBER 7, 2005, THROUGH OCTOBER 30, 2009, EQUIPPED WITH AN AIR RELEASE FIFTH WHEEL. THE INVERSION VALVE ON THE FRAME MAY BE ORIENTATED WHERE CONTAMINANTS CAN ENTER THE VALVE THROUGH THE EXHAUST PORT. AS A RESULT, THE BRAKE VALVE MAY CORRODE. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: ON CERTAIN TRUCKS, THE WHEEL SPACER MAY BECOME DISTORTED FROM HEAT WHICH POTENTIALLY COULD LEAD TO A LOSS OF CLAMP THAT MAY RESULT IN LOOSE WHEEL NUTS. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH D12D ENGINES, THE EXHAUST GAS RECIRCULATION (EGR) COOLER INLET PIPES OR THE PIPES THAT CONNECT THE EGR VALVES TO THE COOLER MAY CRACK OR BREAK. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH D12D ENGINES, THE EXHAUST GAS RECIRCULATION (EGR) COOLER INLET PIPES OR THE PIPES THAT CONNECT THE EGR VALVES TO THE COOLER MAY CRACK OR BREAK. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Recall Details
Problem: ON CERTAIN TRUCKS, THE WHEEL SPACER MAY BECOME DISTORTED FROM HEAT WHICH POTENTIALLY COULD LEAD TO A LOSS OF CLAMP THAT MAY RESULT IN LOOSE WHEEL NUTS. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: ON CERTAIN TRUCKS, THE WHEEL SPACER MAY BECOME DISTORTED FROM HEAT WHICH POTENTIALLY COULD LEAD TO A LOSS OF CLAMP THAT MAY RESULT IN LOOSE WHEEL NUTS. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH D12D ENGINES, THE EXHAUST GAS RECIRCULATION (EGR) COOLER INLET PIPES OR THE PIPES THAT CONNECT THE EGR VALVES TO THE COOLER MAY CRACK OR BREAK. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH VALEO WIPER SYSTEMS, THE WIPER MOTOR MAY BE SUSCEPTIVE TO SALT INTRUSION THAT COULD POSSIBLY LEAD TO A CONDITION WHERE THE CONNECTOR OVERHEATS TO A POINT WHERE THE CONNECTOR COULD IGNITE. Recall Details
Problem: Volvo Trucks North America (Volvo) is recalling certain 2004-2019 Volvo VHD trucks equipped with snow plow lamp preparation kits. The snow plow headlights can be turned on without other exterior lights, and high beam indicator will not work when the snow plow high beams are on. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment." Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH D12D ENGINES, THE EXHAUST GAS RECIRCULATION (EGR) COOLER INLET PIPES OR THE PIPES THAT CONNECT THE EGR VALVES TO THE COOLER MAY CRACK OR BREAK. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH VALEO WIPER SYSTEMS, THE WIPER MOTOR MAY BE SUSCEPTIVE TO SALT INTRUSION THAT COULD POSSIBLY LEAD TO A CONDITION WHERE THE CONNECTOR OVERHEATS TO A POINT WHERE THE CONNECTOR COULD IGNITE. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH JOST INTERNATIONAL JSK 37U SERIES FIFTH WHEELS, A FATIGUE CRACK CAN DEVELOP IN THE BRACKET PIN WELD UNDER CERTAIN LOADING CONDITIONS. Recall Details
Problem: ON CERTAIN HEAVY-DUTY CLASS 8 TRUCKS, THE ASSEMBLED ENGINE PRE-HEATER JUMPER WIRING HARNESS WAS INCORRECTLY ASSEMBLED. Recall Details
Problem: ON CERTAIN HEAVY-DUTY CLASS 8 TRUCKS, THE PINCH BOLT ATTACHING THE STEERING DRAG LINK TO THE PITMAN ARM MAY NOT HAVE BEEN SUFFICIENTLY TIGHTENED. Recall Details
Problem: CERTAIN TRUCKS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, 'SEATING SYSTEMS.' THE BENCH SEAT, AS INSTALLED, DOES NOT THE SEAT PULL REQUIREMENTS OF THE STANDARD. Recall Details
Problem: CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH AN OPTIONAL TWO-MAN PASSENGER BENCH SEAT FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES." ON THE TWO-MAN PASSENGER BENCH SEAT INBOARD (CENTER) POSITION, SEAT BELT D-RING MOUNTING BRACKET WELDNUT, THE WELD IS NOT SUFFICIENT TO MEET THE SEAT BELT PULL REQUIREMENTS . Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS, THE CIRCUIT PROTECTION (I.E. AUTOMATIC CIRCUIT BREAKERS) USED TO PROTECT THE VEHICLE LIGHTING SYSTEM MAY NOT PROVIDE ADEQUATE PROTECTION. Recall Details
Problem: ON CERTAIN TRUCKS, THE WHEEL SPACER MAY BECOME DISTORTED FROM HEAT WHICH POTENTIALLY COULD LEAD TO A LOSS OF CLAMP THAT MAY RESULT IN LOOSE WHEEL NUTS. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: ON CERTAIN TRUCKS, THE WHEEL SPACER MAY BECOME DISTORTED FROM HEAT WHICH POTENTIALLY COULD LEAD TO A LOSS OF CLAMP THAT MAY RESULT IN LOOSE WHEEL NUTS. Recall Details
Problem: CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH AN OPTIONAL TWO-MAN PASSENGER BENCH SEAT FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES." ON THE TWO-MAN PASSENGER BENCH SEAT INBOARD (CENTER) POSITION, SEAT BELT D-RING MOUNTING BRACKET WELDNUT, THE WELD IS NOT SUFFICIENT TO MEET THE SEAT BELT PULL REQUIREMENTS . Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 AXLE BACK VEHICLES, THE TELESCOPING STEERING SHAFT IN SOME DRIVING SITUATIONS COULD BOTTOM OUT AND SIDE LOAD THE STEERING GEAR INPUT SHAFT WHENEVER THE ADJUSTABLE STEERING COLUMN IS ADJUSTED TO THE LOWER POSITION. Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS WITH VOLVO B-RIDE REAR SUSPENSION, THE FORWARD AND/OR REAR DRIVE AXLE UPPER AXLE SEAT COULD BREAK ALLOWING THE AFFECTED AXLE TO SHIFT OUT OF ALIGNMENT. Recall Details
Problem: ON CERTAIN HEAVY-DUTY CLASS 8 TRUCKS, THE ASSEMBLED ENGINE PRE-HEATER JUMPER WIRING HARNESS WAS INCORRECTLY ASSEMBLED. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH JOST INTERNATIONAL JSK 37U SERIES FIFTH WHEELS, A FATIGUE CRACK CAN DEVELOP IN THE BRACKET PIN WELD UNDER CERTAIN LOADING CONDITIONS. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH VALEO WIPER SYSTEMS, THE WIPER MOTOR MAY BE SUSCEPTIVE TO SALT INTRUSION THAT COULD POSSIBLY LEAD TO A CONDITION WHERE THE CONNECTOR OVERHEATS TO A POINT WHERE THE CONNECTOR COULD IGNITE. Recall Details
Problem: Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages." Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH VALEO WIPER SYSTEMS, THE WIPER MOTOR MAY BE SUSCEPTIVE TO SALT INTRUSION THAT COULD POSSIBLY LEAD TO A CONDITION WHERE THE CONNECTOR OVERHEATS TO A POINT WHERE THE CONNECTOR COULD IGNITE. Recall Details
Problem: CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH AN OPTIONAL TWO-MAN PASSENGER BENCH SEAT FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES." ON THE TWO-MAN PASSENGER BENCH SEAT INBOARD (CENTER) POSITION, SEAT BELT D-RING MOUNTING BRACKET WELDNUT, THE WELD IS NOT SUFFICIENT TO MEET THE SEAT BELT PULL REQUIREMENTS . Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH JOST INTERNATIONAL JSK 37U SERIES FIFTH WHEELS, A FATIGUE CRACK CAN DEVELOP IN THE BRACKET PIN WELD UNDER CERTAIN LOADING CONDITIONS. Recall Details
Problem: VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY, AXLE BACK MODEL VEHICLES. THE DESIGN OF THE LOWER STEERING COLUMN SHAFT UNIVERSAL JOINT BOOT COULD ALLOW THE BOOT TO GET ENTANGLED IN THE UNIVERSAL JOINT. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS. THE LOWER STEERING SHAFT MAY SIDE-LOAD THE STEERING GEAR INPUT SHAFT. THIS CONDITION COULD RESULT IN NON-UNIFORM STEERING WHEEL EFFORTS WHEN TURNING THE STEERING WHEEL. IN ADDITION, ONCE THE STEERING WHEEL TURN IS INITIATED, THE VEHICLE MAY CONTINUE TURNING WITHOUT RETURNING TO THE STRAIGHT AHEAD POSITION WITH DRIVER EFFORT. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH A STEERABLE AUXILIARY AXLE AND EQUIPPED WITH CERTAIN MERITOR-WABCO BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED. Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS, THE FORWARD AND/OR REAR DRIVE AXLE UPPER AXLE SEAT CAN BREAK ALLOWING THE AXLE TO SHIFT OUT OF ALIGNMENT. Recall Details
Problem: ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH MERITOR WABCO PNEUMATIC ANITLOCK BRAKE SYSTEM (ABS) VALVE PACKAGES, THE ASSEMBLY BOLTS ON THESE VALVE PACKAGES WERE NOT TIGHTENED CORRECTLY. Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 AXLE BACK VEHICLES, THE TELESCOPING STEERING SHAFT IN SOME DRIVING SITUATIONS COULD BOTTOM OUT AND SIDE LOAD THE STEERING GEAR INPUT SHAFT WHENEVER THE ADJUSTABLE STEERING COLUMN IS ADJUSTED TO THE LOWER POSITION. Recall Details
Problem: VOLVO TRUCKS IS RECALLING 127,764 MY 2001-2008 VHD, VNL, VNM, AND MY 2005-2008 VT TRUCKS. A SEAL MAY FAIL ALLOWING WATER AND CONTAMINANTS TO SEEP INTO THE WINDSHIELD WIPER MOTOR. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH A STEERABLE AUXILIARY AXLE AND EQUIPPED WITH CERTAIN MERITOR-WABCO BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS. THE LOWER STEERING SHAFT MAY SIDE-LOAD THE STEERING GEAR INPUT SHAFT. THIS CONDITION COULD RESULT IN NON-UNIFORM STEERING WHEEL EFFORTS WHEN TURNING THE STEERING WHEEL. IN ADDITION, ONCE THE STEERING WHEEL TURN IS INITIATED, THE VEHICLE MAY CONTINUE TURNING WITHOUT RETURNING TO THE STRAIGHT AHEAD POSITION WITH DRIVER EFFORT. Recall Details
Problem: VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY, AXLE BACK MODEL VEHICLES. THE DESIGN OF THE LOWER STEERING COLUMN SHAFT UNIVERSAL JOINT BOOT COULD ALLOW THE BOOT TO GET ENTANGLED IN THE UNIVERSAL JOINT. Recall Details
Problem: CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH AN OPTIONAL TWO-MAN PASSENGER BENCH SEAT FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES." ON THE TWO-MAN PASSENGER BENCH SEAT INBOARD (CENTER) POSITION, SEAT BELT D-RING MOUNTING BRACKET WELDNUT, THE WELD IS NOT SUFFICIENT TO MEET THE SEAT BELT PULL REQUIREMENTS . Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 AXLE BACK VEHICLES, THE TELESCOPING STEERING SHAFT IN SOME DRIVING SITUATIONS COULD BOTTOM OUT AND SIDE LOAD THE STEERING GEAR INPUT SHAFT WHENEVER THE ADJUSTABLE STEERING COLUMN IS ADJUSTED TO THE LOWER POSITION. Recall Details
Problem: ON SOME HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS, THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH VALEO WIPER SYSTEMS, THE WIPER MOTOR MAY BE SUSCEPTIVE TO SALT INTRUSION THAT COULD POSSIBLY LEAD TO A CONDITION WHERE THE CONNECTOR OVERHEATS TO A POINT WHERE THE CONNECTOR COULD IGNITE. Recall Details
Problem: ON SOME HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS, THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Recall Details
|