| Component | Summary |
100000 POWER TRAIN | Jul 09, 2021 - CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
010000 STEERING | May 10, 2021 - If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut P |
010000 STEERING | May 10, 2021 - SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when imprope |
010000 STEERING | May 10, 2021 - SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into |
020000 SUSPENSION | May 10, 2021 - IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle; when making, turns, on dry roads, or at low speeds (under 40 MPH), and the vibration does not occur if the Electric Controlled Coupling is electrically dis |
020000 SUSPENSION | May 10, 2021 - SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition wh |
020000 SUSPENSION | May 10, 2021 - SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into |
030000 BRAKES (PWS) | May 10, 2021 - If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut P |
030000 BRAKES (PWS) | May 10, 2021 - SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when imprope |
030000 BRAKES (PWS) | May 10, 2021 - SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into |
030000 BRAKES (PWS) | May 10, 2021 - SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Da |
060000 ENGINE (PWS) | May 10, 2021 - SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin f |
060000 ENGINE (PWS) | May 10, 2021 - SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-D |
060000 ENGINE AND ENGINE COOLING | May 10, 2021 - SERVICE INFORMATION The R&I (Remove and Install) procedure on an applied vehicle for blower motor service will be amended to include the knee bracket. If a blower motor is to be removed and reinstalled or replaced, add the step shown in |
061600 ENGINE AND ENGINE COOLING, ENGINE, ENGINE CONTROL MODULE (ECU/ECM) | May 10, 2021 - SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin f |
063000 ENGINE AND ENGINE COOLING, EXHAUST SYSTEM | May 10, 2021 - IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail |
063100 ENGINE AND ENGINE COOLING, EXHAUST SYSTEM, EMISSION CONTROL | May 10, 2021 - SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon loca |
074000 FUEL/PROPULSION SYSTEM (PWS) | May 10, 2021 - SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm th |
100000 POWER TRAIN | May 10, 2021 - IF YOU CONFIRM The vehicle has slower than normal acceleration from a stop at times, and/or the customer describes the vehicle has slower than normal acceleration from a stop at times, and/or The MIL is ON with DTC P1778 (STEP MOTOR) |
100000 POWER TRAIN | May 10, 2021 - IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear CV-type axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: |
| 1 2 3 4 5 6 7 |