by General Motors, LLC
CHEVROLET P3 RECALLS - (13 Recalls Found)
Since 1969, CHEVROLET has issued a total of 3866 car recalls worldwide. Of those recalls, 13 have been for the CHEVROLET P3 starting in 1991. This accounts for approximately 6.7% of the 58048 car recalls issued by the NHTSA since 1966. The P3 accounts for less than 1.0% of all the CHEVROLET recalls issued since 1969. Compared to other car manufacturers, CHEVROLET ranks #3 in overall number of recalls issued by a car maker.
Please keep in mind these numbers are for statistical purposes only & do not necessarily reflect the quality of the CHEVROLET P3 or CHEVROLET itself. These figures are based only on the number of recalls issued and NOT the total number of vehicles affected by a particular recall.
Find your CHEVROLET P3 listed below. Results are sorted year from newest to oldest. Select the desired CHEVROLET P3 to view the complete recall details.
Information provided by the National Highway Traffic Safety Administration.
| View CHEVROLET P3 Recalls Below ↓ |
|
1996 Recalls ↓
Problem: THE ENGINE COOLING FAN ASSEMBLIES CAN BREAK FROM FATIGUE CAUSED BY ENGINE AND/OR VEHICLE INDUCED STRESSES. Recall Details - 1/16/1996
1992 Recalls ↓
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
1991 Recalls ↓
Problem: BRAKES MAY HAVE MISSING REAR AXLE OUTER BEARING RETAINING RING AND OR GREATER THAN SPECIFIED BEARING END PLAY. EITHER CONDITION ALLOWS THE ROTOR AND HUB ASSEMBLY TO SHIFT POSITION RELATIVE TO THE SPINDLE. THIS MOVEMENT CAN CAUSE BRAKE CALIPER PISTON RECEDE FARTHER THAN NORMAL INTO THE PISTON BORE WHICH WOULD REQUIRE GREATER THAN NORMAL BRAKE FLUID DISPLACEMENT WHEN THE SERVICE BRAKES ARE APPLIED. Recall Details - 7/16/1991
Problem: THE AUTOMATIC APPLY TRANSMISSION MOUNTED PARKING BRAKE LEVER PIVOT BOLT "FINGER" MAY BE LOOSE. Recall Details - 8/5/1991
Problem: SOME CHASSIS WERE SHIPPED TO BODY BUILDERS WITH DAMAGED FILL OR VENT OPENING CAPS ON THE RIGHT-HAND SIDE. IF A LEFT-HAND FILL SYSTEM WAS INSTALLED ON THE TANK, AND THERE WAS A DAMAGED RIGHT-HAND CAP, THE FUEL SYSTEM WOULD NOT BE SEALED. Recall Details - 12/13/1991
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
1990 Recalls ↓
Problem: BRAKES MAY HAVE MISSING REAR AXLE OUTER BEARING RETAINING RING AND OR GREATER THAN SPECIFIED BEARING END PLAY. EITHER CONDITION ALLOWS THE ROTOR AND HUB ASSEMBLY TO SHIFT POSITION RELATIVE TO THE SPINDLE. THIS MOVEMENT CAN CAUSE BRAKE CALIPER PISTON RECEDE FARTHER THAN NORMAL INTO THE PISTON BORE WHICH WOULD REQUIRE GREATER THAN NORMAL BRAKE FLUID DISPLACEMENT WHEN THE SERVICE BRAKES ARE APPLIED. Recall Details - 7/16/1991
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
1989 Recalls ↓
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
1988 Recalls ↓
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
1987 Recalls ↓
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
1986 Recalls ↓
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
1985 Recalls ↓
Problem: THE 19.5 X 6 FRONT STEEL WHEEL DISC CRACKS OUTSIDE THE MOUNTING BOLT CIRCLE AND ENDS AT THE HUB'S DIAMETER. Recall Details - 9/8/1992
|