|
2006 Recalls ↓
Problem: Mazda North America Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2006-2007 Mazdaspeed6 and 2004 MPV vehicles nationwide. Mazda is also recalling 2005-2006 MPV vehicles in Alabama, Arizona, Arkansas, California, Delaware, the District of Columbia, Florida, Georgia, Hawaii, Illinois, Indiana, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands. On July 9, 2019 this recall was expanded to include certain 2004-2011 RX-8 vehicles that were previously recalled under 16V-354 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Recall Details - 6/15/2018
Problem: Mazda North America Operations (Mazda) is recalling certain 2005-2006 Mazda MPV vehicles sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. On July 9, 2019 this recall was expanded to include certain 2005-2009 RX-8 vehicles that were previously recalled under 17V-011 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Recall Details - 6/15/2018
2005 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2004-2005 MPV, 2004 RX-8, and 2006-2007 Mazdaspeed6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling. Recall Details - 10/31/2019
Problem: Mazda North America Operations (Mazda) is recalling certain 2005-2006 Mazda MPV vehicles sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. On July 9, 2019 this recall was expanded to include certain 2005-2009 RX-8 vehicles that were previously recalled under 17V-011 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Recall Details - 6/15/2018
Problem: Mazda North America Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2006-2007 Mazdaspeed6 and 2004 MPV vehicles nationwide. Mazda is also recalling 2005-2006 MPV vehicles in Alabama, Arizona, Arkansas, California, Delaware, the District of Columbia, Florida, Georgia, Hawaii, Illinois, Indiana, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands. On July 9, 2019 this recall was expanded to include certain 2004-2011 RX-8 vehicles that were previously recalled under 16V-354 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Recall Details - 6/15/2018
2004 Recalls ↓
Problem: Mazda North America Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2006-2007 Mazdaspeed6 and 2004 MPV vehicles nationwide. Mazda is also recalling 2005-2006 MPV vehicles in Alabama, Arizona, Arkansas, California, Delaware, the District of Columbia, Florida, Georgia, Hawaii, Illinois, Indiana, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, South Carolina, Tennessee, Texas, Virginia, West Virginia, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands. On July 9, 2019 this recall was expanded to include certain 2004-2011 RX-8 vehicles that were previously recalled under 16V-354 but have not yet been repaired. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Recall Details - 6/15/2018
Problem: Mazda North American Operations (Mazda) is recalling certain 2003-2008 Mazda6, 2004-2005 MPV, 2004 RX-8, and 2006-2007 Mazdaspeed6 vehicles. These vehicles had their passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling. Recall Details - 10/31/2019
Problem: AS A RESULT OF AN NCAP TEST, CERTAIN MINIVANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE FRONT PASSENGER SEAT AIR BAG WAS NOT CORRECTLY WIRING. Recall Details - 2/17/2004
Problem: CERTAIN MINIVANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." SOME OF THESE VEHICLES WERE PRODUCED WITH AIR BAG WARNING LABELS INTENDED FOR THE CANADIAN MARKET. THUS, THE LABELS CONTAIN WARNINGS IN BOTH ENGLISH AND FRENCH. AS A RESULT, THE AREA OF THE ENGLISH WARNING IS ONLY 16 SQUARE CENTIMETERS, AS OPPOSED TO THE 30 SQUARE CENTIMETERS REQUIRED BY THE STANDARD. Recall Details - 3/9/2004
Problem: THE TIRE INFLATION PRESSURE INDICATED ON THE VEHICLE CERTIFICATION LABEL IS NOT CORRECT. THE LABELS SHOW THE MAXIMUM TIRE PRESSURE AS 240 KPA/32 PSI WHEN IT SHOULD BE SHOWN AS 240 KPA/35 PSI. AS A RESULT OF THIS ERROR, THE LOAD RATIOS FOR THE 205/65R15 94H AND THE 215/60R16 95H TIRES EXCEED THE LEVELS PERMITTED BY FMVSS 120. Recall Details - 6/10/2004
2003 Recalls ↓
Problem: THE TIRE INFLATION PRESSURE INDICATED ON THE VEHICLE CERTIFICATION LABEL IS NOT CORRECT. THE LABELS SHOW THE MAXIMUM TIRE PRESSURE AS 240 KPA/32 PSI WHEN IT SHOULD BE SHOWN AS 240 KPA/35 PSI. AS A RESULT OF THIS ERROR, THE LOAD RATIOS FOR THE 205/65R15 94H AND THE 215/60R16 95H TIRES EXCEED THE LEVELS PERMITTED BY FMVSS 120. Recall Details - 6/10/2004
Problem: CERTAIN MINIVANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." SOME OF THESE VEHICLES WERE PRODUCED WITH AIR BAG WARNING LABELS INTENDED FOR THE CANADIAN MARKET. THUS, THE LABELS CONTAIN WARNINGS IN BOTH ENGLISH AND FRENCH. AS A RESULT, THE AREA OF THE ENGLISH WARNING IS ONLY 16 SQUARE CENTIMETERS, AS OPPOSED TO THE 30 SQUARE CENTIMETERS REQUIRED BY THE STANDARD. Recall Details - 3/9/2004
Problem: ON CERTAIN MINI VANS AND PASSENGER VEHICLES, THE SOCKET HOLDER IN THE FOG LIGHTS IS INSTALLED IN THE LAMP CASING USING PRESSURE. DURING OPERATION OF THE FOG LIGHT, THE HEAT FROM THE BULB CAN EXPAND THE SOCKET HOLDER. THE EXPANSION CAN FORCE THE SOCKET HOLDER REARWARD. AFTER REPEATEDLY BEING SUBJECT TO THIS EXPANSION, IF THE FOG LIGHT IS ALSO SUBJECTED TO VIBRATION DURING VEHICLE OPERATION, THE SOCKET HOLDER WITH THE BULB HOLDER AND THE WIRING HARNESS MAY SEPARATE FROM THE FOG LIGHT CASING. Recall Details - 6/5/2003
Problem: ON CERTAIN MINI VANS EQUIPPED WITH FRONT FOG LIGHTS,THE FOG LIGHT BULB SOCKET MAY HAVE BEEN INSTALLED IMPROPERLY. Recall Details - 2/13/2003
2002 Recalls ↓
Problem: ON CERTAIN MINI VANS AND PASSENGER VEHICLES, THE SOCKET HOLDER IN THE FOG LIGHTS IS INSTALLED IN THE LAMP CASING USING PRESSURE. DURING OPERATION OF THE FOG LIGHT, THE HEAT FROM THE BULB CAN EXPAND THE SOCKET HOLDER. THE EXPANSION CAN FORCE THE SOCKET HOLDER REARWARD. AFTER REPEATEDLY BEING SUBJECT TO THIS EXPANSION, IF THE FOG LIGHT IS ALSO SUBJECTED TO VIBRATION DURING VEHICLE OPERATION, THE SOCKET HOLDER WITH THE BULB HOLDER AND THE WIRING HARNESS MAY SEPARATE FROM THE FOG LIGHT CASING. Recall Details - 6/5/2003
Problem: CERTAIN MINI VANS FAIL TO COMPLY TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS." AN INCORRECT GROSS AXLE WEIGHT RATING (GAWR) WAS INDICATED ON THE CERTIFICATION LABEL. Recall Details - 3/20/2002
Problem: ON CERTAIN MINI VANS EQUIPPED WITH FRONT FOG LIGHTS,THE FOG LIGHT BULB SOCKET MAY HAVE BEEN INSTALLED IMPROPERLY. Recall Details - 2/13/2003
Problem: ON CERTAIN MINIVANS EQUIPPED WITH CRUISE CONTROL, THE CRUISE CONTROL ACTUATOR CABLE MAY BE BROKEN DUE TO INSUFFICIENT STRENGTH (GROUP 1). ALSO INCLUDED ARE CERTAIN 2000-2001 MINIVANS EQUIPPED WITH CRUISE CONTROL BUILT BETWEEN MARCH 31, 1999 AND MARCH 31, 2001, THAT HAVE HAD THE CRUISE CONTROL REPAIRED AND POSSIBLY HAD A DEFECTIVE CABLE INSTALLED DURING THAT REPAIR (GROUP 2). Recall Details - 5/19/2004
2001 Recalls ↓
Problem: ON CERTAIN MINIVANS EQUIPPED WITH CRUISE CONTROL, THE CRUISE CONTROL ACTUATOR CABLE MAY BE BROKEN DUE TO INSUFFICIENT STRENGTH (GROUP 1). ALSO INCLUDED ARE CERTAIN 2000-2001 MINIVANS EQUIPPED WITH CRUISE CONTROL BUILT BETWEEN MARCH 31, 1999 AND MARCH 31, 2001, THAT HAVE HAD THE CRUISE CONTROL REPAIRED AND POSSIBLY HAD A DEFECTIVE CABLE INSTALLED DURING THAT REPAIR (GROUP 2). Recall Details - 5/19/2004
Problem: ON CERTAIN PASSENGER VEHICLES, SOME OF THE PASSENGER AIR BAG MODULES WERE NOT PROPERLY WELDED AND MAY NOT DEPLOY IN A COLLISION. Recall Details - 8/5/2002
Problem: VEHICLE DESCRIPTION: CERTAIN MINI VANS WITHOUT ANTI-LOCK BRAKING SYSTEMS (ABS) FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 135, "PASSENGER CAR BRAKE SYSTEMS." DUE TO INAPPROPRIATE BRAKE PIPE LAYOUT, THESE VEHICLES DO NOT MEET THE BRAKE STOPPING DISTANCE WITH PARTIAL FAILURE REQUIREMENTS OF THE STANDARD. Recall Details - 12/17/2001
2000 Recalls ↓
Problem: VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH ENGINES SUPPLIED BY FORD MOTOR COMPANY CLEVELAND ENGINE PLANT. THESE ENGINES ARE INSTALLED WITH FUEL INJECTORS THAT DO NOT MATCH THE LOWER INTAKE MANIFOLD Recall Details - 7/7/1999
Problem: VEHICLE DESCRIPTION: MINIVANS. DUE TO THE INAPPROPRIATE SHAPE OF THE LINKAGE IN THE REAR DOOR LOCK CONTROLLER, ACCUMULATED DUST MAY PREVENT THE DOOR LOCK MECHANISM FROM FUNCTIONING PROPERLY, CAUSING INCOMPLETE LOCKING OF THE DOOR WHEN THE CHILDPROOF LOCKING SYSTEM IS USED. Recall Details - 7/16/1999
Problem: VEHICLE DESCRIPTION: MINI VANS. THESE MINI VANS DO NOT HAVE TIRE INFORMATION LABELS THAT COMPLY WITH SECTION 5.3 OF FMVSS 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS." Recall Details - 4/11/2000
Problem: VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH ORIGINAL EQUIPMENT 16 INCH TIRES. THESE MINI VANS DO NOT HAVE THE CORRECT RECOMMENDED COLD INFLATION PRESSURE ON THE LABEL AND THUS DO NOT COMPLY WITH SECTION 5.1.2 OF FMVSS 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS." Recall Details - 4/11/2000
Problem: VEHICLE DESCRIPTION: CERTAIN MINI VANS WITHOUT ANTI-LOCK BRAKING SYSTEMS (ABS) FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 135, "PASSENGER CAR BRAKE SYSTEMS." DUE TO INAPPROPRIATE BRAKE PIPE LAYOUT, THESE VEHICLES DO NOT MEET THE BRAKE STOPPING DISTANCE WITH PARTIAL FAILURE REQUIREMENTS OF THE STANDARD. Recall Details - 12/17/2001
1998 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1997 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1996 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1995 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1994 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1993 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1992 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1991 Recalls ↓
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
Problem: THE REAR BRAKE LININGS CAN CHANGE OVER TIME. AS THE BRAKES WEAR, THE COEFFICIENT OF FRICTION CAN INCREASE, PRODUCING INCONSISTENT REAR BRAKE PERFORMANCE AND PREMATURE ACTIVATION OF THE ABS SYSTEM. Recall Details - 2/27/1992
Problem: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY. Recall Details - 5/24/1995
1990 Recalls ↓
Problem: THE REAR BRAKE LININGS CAN CHANGE OVER TIME. AS THE BRAKES WEAR, THE COEFFICIENT OF FRICTION CAN INCREASE, PRODUCING INCONSISTENT REAR BRAKE PERFORMANCE AND PREMATURE ACTIVATION OF THE ABS SYSTEM. Recall Details - 2/27/1992
Problem: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY. Recall Details - 5/24/1995
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
1989 Recalls ↓
Problem: THE FRONT SAFETY BELT BUCKLE RELEASE BUTTONS CAN BREAK. THESE RED PLASTIC RELEASE BUTTONS ARE MARKED "PRESS." IF A BUTTON BREAKS, PIECES CAN FALL INTO THE BUCKLE ASSEMBLY CAUSING THE BUCKLE TO OPERATE IMPROPERLY. Recall Details - 5/24/1995
Problem: THE CENTER SAFETY BELT ATTACHMENT HARDWARE BRACKETS FOR THE THIRD SEAT MAY NOT WITHSTAND THE SPECIFIED TENSILE LOAD. Recall Details - 11/7/1989
Problem: WHEN THE VEHICLE IS EXPOSED TO TEMPERATURES BELOW 5 DEGREES FAHRENHEIT (-15 DEGREES C), THE NEUTRAL DETERGENT USED AS AN ASSEMBLY LUBRICANT MAY STICK TO THE CHECK VALVE, PREVENTING VALVE FROM FUNCTIONING. Recall Details - 1/22/1991
Problem: WHEN APPLYING THE FOOT (SERVICE) BRAKE IN THE LOW VEHICLE SPEED CONDITION, THE BRAKING POWER PRODUCED MAY BE MORE THAN EXPECTED. Recall Details - 9/11/1991
Problem: Mazda North American Operations (Mazda) is recalling certain model year 1989-1998 MPV, 1990-1995 323, 1990-1998 Protege, 1992-1993 MX-3, 1993-1995 929, 1993-1997 MX-6, and 1993-1998 626 vehicles. In the affected vehicles, grease applied to the contact points inside the ignition switch may become conductive and overheat. Recall Details - 10/19/2015
|