|
Problem: ON CERTAIN TRUCKS, A LEAK IN THE ASET AC FUEL INJECTION LINE MAY SPRAY FUEL ON THE EXHAUST GAS RECIRCULATION PIPES THAT CARRY HOT EXHAUST GASES . Recall Details
Problem: CERTAIN TRUCKS WERE RECALLED FOR THE INSTALLATION OF SLEEVES ON THE FUEL INJECTION LINE AS REQUIRED BY SAFETY RECALL SC0317 (NHTSA RECALL NO. 06V392). THERE IS A POSSIBILITY THAT THE NEW SLEEVES MAY CHAFE THE FUEL INJECTION LINE. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH ASET AC MODEL ENGINES, THE ENGINE AS CONFIGURED WITH AN EXTERNAL EXHAUST GAS RECIRCULATION SYSTEM MAKES SERVICING THE FUEL INJECTION LINES DIFFICULT WHEN USING TRADITIONAL TOOLS. THEREFORE, IT IS POSSIBLE FOR FUEL LEAKS TO DEVELOP WHEN REMOVING AND INSTALLING THE FUEL INJECTION LINES. Recall Details
Problem: ON CERTAIN TRUCKS, A LEAK IN THE ASET AC FUEL INJECTION LINE MAY SPRAY FUEL ON THE EXHAUST GAS RECIRCULATION PIPES THAT CARRY HOT EXHAUST GASES . Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH ASET AC MODEL ENGINES, THE ENGINE AS CONFIGURED WITH AN EXTERNAL EXHAUST GAS RECIRCULATION SYSTEM MAKES SERVICING THE FUEL INJECTION LINES DIFFICULT WHEN USING TRADITIONAL TOOLS. THEREFORE, IT IS POSSIBLE FOR FUEL LEAKS TO DEVELOP WHEN REMOVING AND INSTALLING THE FUEL INJECTION LINES. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH ASET AC MODEL ENGINES, THE ENGINE AS CONFIGURED WITH AN EXTERNAL EXHAUST GAS RECIRCULATION SYSTEM MAKES SERVICING THE FUEL INJECTION LINES DIFFICULT WHEN USING TRADITIONAL TOOLS. THEREFORE, IT IS POSSIBLE FOR FUEL LEAKS TO DEVELOP WHEN REMOVING AND INSTALLING THE FUEL INJECTION LINES. Recall Details
Problem: ON CERTAIN TRUCKS, A LEAK IN THE ASET AC FUEL INJECTION LINE MAY SPRAY FUEL ON THE EXHAUST GAS RECIRCULATION PIPES THAT CARRY HOT EXHAUST GASES . Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 DIESEL TRUCKS EQUIPPED WITH ASET AC ENGINES, THE LOCATION OF THE FUEL INLET HOSE MAY RESULT IN OVERHEATING OR ABRASION OF THE HOSE, WHICH MAY LEAD TO A PREMATURE FAILURE. Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 DIESEL TRUCKS EQUIPPED WITH ASET AC ENGINES, THE LOCATION OF THE FUEL INLET HOSE MAY RESULT IN OVERHEATING OR ABRASION OF THE HOSE, WHICH MAY LEAD TO A PREMATURE FAILURE. Recall Details
Problem: ON CERTAIN TRUCKS, A LEAK IN THE ASET AC FUEL INJECTION LINE MAY SPRAY FUEL ON THE EXHAUST GAS RECIRCULATION PIPES THAT CARRY HOT EXHAUST GASES . Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH ASET AC MODEL ENGINES, THE ENGINE AS CONFIGURED WITH AN EXTERNAL EXHAUST GAS RECIRCULATION SYSTEM MAKES SERVICING THE FUEL INJECTION LINES DIFFICULT WHEN USING TRADITIONAL TOOLS. THEREFORE, IT IS POSSIBLE FOR FUEL LEAKS TO DEVELOP WHEN REMOVING AND INSTALLING THE FUEL INJECTION LINES. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: ON CERTAIN TRUCK CHASSIS, THE STEERING GEAR MOUNTING BOLTS WERE OVER-TORQUED AT INSTALLATION. THE STEERING GEAR IS MOUNTED TO THE VEHICLE'S FRAME RAIL WITH 3 BOLTS. Recall Details
Problem: ON CERTAIN TRUCK CHASSIS, THE STEERING GEAR MOUNTING BOLTS WERE MADE OF INCONSISTENT BOLT MATERIAL, WHICH HAS LED TO BOLT FAILURES. THIS INCONSISTENT BOLT MATERIAL CONDITION COULD RESULT IN A FAILURE OF A STEERING GEAR MOUNTING BOLTS. THE STEERING GEAR IS MOUNTED TO THE VEHICLE'S FRAME WITH THREE BOLTS. Recall Details
Problem: CERTAIN HEAVY DUTY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." IMPROPER SEATING OF THE CHECK VALVE RETAINER IN THE BRASS FITTING HOUSING HAS OCCURRED. IT IS POSSIBLE FOR THE AIR BRAKE SYSTEM PRESSURE TO PUSH THE CHECK VALVE INTERNAL PARTS INTO THE PRIMARY SYSTEM RESERVOIR AND A VEHICLE OPERATOR WOULD NOT KNOW THAT THIS HAS HAPPENED. Recall Details
Problem: ON CERTAIN CHASSIS EQUIPPED WITH DANA STEERING AXLE ASSEMBLIES. THESE AXLES ARE BUILT WITH AN INTEGRAL KNUCKLE AND STEERING ARM. THE STEERING ARM COULD HAVE LONGITUDINAL CRACKS. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH ASET AC MODEL ENGINES, THE ENGINE AS CONFIGURED WITH AN EXTERNAL EXHAUST GAS RECIRCULATION SYSTEM MAKES SERVICING THE FUEL INJECTION LINES DIFFICULT WHEN USING TRADITIONAL TOOLS. THEREFORE, IT IS POSSIBLE FOR FUEL LEAKS TO DEVELOP WHEN REMOVING AND INSTALLING THE FUEL INJECTION LINES. Recall Details
Problem: ON CERTAIN TRUCKS, A LEAK IN THE ASET AC FUEL INJECTION LINE MAY SPRAY FUEL ON THE EXHAUST GAS RECIRCULATION PIPES THAT CARRY HOT EXHAUST GASES . Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 DIESEL TRUCKS EQUIPPED WITH ASET AC ENGINES, THE LOCATION OF THE FUEL INLET HOSE MAY RESULT IN OVERHEATING OR ABRASION OF THE HOSE, WHICH MAY LEAD TO A PREMATURE FAILURE. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH ASET AC MODEL ENGINES, THE ENGINE AS CONFIGURED WITH AN EXTERNAL EXHAUST GAS RECIRCULATION SYSTEM MAKES SERVICING THE FUEL INJECTION LINES DIFFICULT WHEN USING TRADITIONAL TOOLS. THEREFORE, IT IS POSSIBLE FOR FUEL LEAKS TO DEVELOP WHEN REMOVING AND INSTALLING THE FUEL INJECTION LINES. Recall Details
Problem: CERTAIN CLASS 8 CHASSIS FAIL TO COMPLY WITH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE INSTALLATION OF THE ADDITIONAL AXLE(S), RAISES THE GVW CAPABILITY OF THE VEHICLE AND THEREFORE REQUIRES AN INCREASE IN THE PARKING BRAKE PERFORMANCE TO HOLD ON A 20% GRADE IN ORDER TO MEET THE REQUIREMENTS OF THE STANDARD. Recall Details
Problem: ON CERTAIN TRUCKS EQUIPPED WITH MANIFOLD DASH VALVES WITH PUSH TO CONNECT FITTINGS USED TO CONTROL THE PARK BRAKE FUNCTION ON TRUCKS AND TRAILERS WITH AIR BRAKES, THE PARK KNOB CAN POP OUT UNEXPECTEDLY WHILE THE VEHICLE IS IN MOTION. THIS WILL EXHAUST THE AIR FROM THE PARK BRAKE SYSTEM ON THE TRAILER AND APPLY THE PARKING BRAKES. Recall Details
Problem: ON CERTAIN HEAVY DUTY CLASS 8 DIESEL TRUCKS EQUIPPED WITH ASET AC ENGINES, THE LOCATION OF THE FUEL INLET HOSE MAY RESULT IN OVERHEATING OR ABRASION OF THE HOSE, WHICH MAY LEAD TO A PREMATURE FAILURE. Recall Details
Problem: ON CERTAIN CLASS 8 CHASSIS EQUIPPED WITH R. H. SHEPPARD "M100" STEERING GEARS AND TRW "TAS65" STEERING GEARS, A POWER STEERING HOSE WITH AN INCORRECT PRESSURE RATING WAS INSTALLED BY THE FACTORY. Recall Details
Problem: ON CERTAIN CLASS 8 HEAVY DUTY TRUCKS EQUIPPED WITH R. H. SHEPPARD M90 STEERING GEARS, AN INCORRECT HOSE WAS USED FOR THE HIGH-PRESSURE LINE BETWEEN THE POWER STEERING PUMP AND THE STEERING GEAR. THE HOSE IS RATED AT 2000 PSI, WHILE IT SHOULD BE RATED AT 3000 PSI. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CERTAIN MERITOR-WABCO BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED. Recall Details
Problem: VEHICLE DESCRIPTION: TRUCKS EQUIPPED WITH E-TECH ENGINES. A CONDITION EXISTS ON THE AUXILIARY DRIVE SHAFT OF THE E-TECH ENGINE THAT CAUSES THE LOSS OF POWER STEERING ON VEHICLES WHERE THE POWER STEERING PUMP IS MOUNTED OFF THE FRONT OF THE ENGINE. Recall Details
Problem: ON CERTAIN HEAVYTRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: ON SOME HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS, THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: ON CERTAIN CLASS 8 HEAVY DUTY TRUCKS EQUIPPED WITH R. H. SHEPPARD M90 STEERING GEARS, AN INCORRECT HOSE WAS USED FOR THE HIGH-PRESSURE LINE BETWEEN THE POWER STEERING PUMP AND THE STEERING GEAR. THE HOSE IS RATED AT 2000 PSI, WHILE IT SHOULD BE RATED AT 3000 PSI. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN DANA/SPICER AXLES (E12001) AND MACK AXLES THROUGH DANA HEAVY AXLE (FAWL 12). THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CERTAIN MERITOR-WABCO BRAKE SYSTEM TWO AND FOUR PORT RELAY VALVES. THE VALVE MAY STICK OPEN WHEN A HIGH-PRESSURE APPLICATION IS RELEASED. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Recall Details
Problem: VEHICLE DESCRIPTION: CLASS 8 TRUCKS EQUIPPED WITH FELSTED ELECTRONIC ACCELERATOR PEDALS. THE RETURN SPRINGS CAN BREAK ON THE ACCELERATOR PEDALS THAT ARE EQUIPPED WITH STAINLESS STEEL OR ELECTROPLATED WIRE RETURN SPRINGS. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH DRAG LINK ASSEMBLIES CONTAINING 24-DL MODEL BALL SOCKETS AND MANUFACTURED BY TRW. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET. Recall Details
Problem: VEHICLE DESCRIPTION: CLASS 8 TRUCKS EQUIPPED WITH FELSTED ELECTRONIC ACCELERATOR PEDALS. THE RETURN SPRINGS CAN BREAK ON THE ACCELERATOR PEDALS THAT ARE EQUIPPED WITH STAINLESS STEEL OR ELECTROPLATED WIRE RETURN SPRINGS. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Recall Details
Problem: ON SOME HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS, THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: ON CERTAIN HEAVYTRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Recall Details
Problem: ON CERTAIN HEAVYTRUCKS EQUIPPED WITH TRUCK HUB UNITS MANUFACTURED BY SKF EXCLUSIVELY FOR USE ON ARVINMERITOR'S FF98X SERIES NON-DRIVE STEER AXLES, THE HUB UNIT BEARINGS CAN WEAR PREMATURELY. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS WITH AN EC-17 1030R ELECTRONIC CONTROL UNIT (ECU), THERE HAVE BEEN REPORTS OF UNWANTED ABS ACTIVATION AT LOW SPEEDS CAUSED BY 1) CHAFED ABS WHEEL SPEED SENSOR WIRES ON ROTATING PARTS OR 2) A DAMAGED COMPONENT AT THE WHEEL END THAT GENERATES A CERTAIN TYPE OF ERRATIC SENSOR SIGNAL. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: VEHICLE DESCRIPTION: CLASS 8 HEAVY DUTY TRUCKS. DURING ASSEMBLY, INSUFFICIENT TORQUE OCCURRED OF THE DRAG LINK TO THE AXLE STEERING ARM CONNECTION. IF THE DRAG LINK TO AXLE STTERING ARM CONNECTION IS NOT TORQUED AND THE COTTER PIN IS NOT INSTALLED, THE NUT COULD BACK OFF DURING VEHICLE OPERATION. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH DESIGN LEVEL 1, ROCKWELL FF980 SERIES FRONT AXLE. THE FRONT AXLE HUB FLANGE CAN DEVELOP CRACKS DUE TO HIGH STRESS LEVELS. Recall Details
Problem: THE U-JOINT BEARING STRAP BOLTS WERE NOT PROPERLY TIGHTENED DURING ASSEMBLY. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: ON CERTAIN CHASSIS BUILT WITH LNG ENGINES, THE NEXGEN LNG TANK'S PRIMARY AND SECONDARY RELIEF VALVES COULD FAIL TO OPEN AND RELIEVE TANK PRESSURE. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH FONTAINE FIFTH WHEEL ASSEMBLIES. THE FIFTH WHEEL MOUNTING PLATES CAN CRACK. Recall Details
Problem: THE DRIVESHAFT CENTER BEARING SUPPORT BRACKET CAN CRACK AND BREAK. Recall Details
Problem: THE CARRIER YOKE BOLTS WERE MANUFACTURED WITH WORN ROLLING THREAD DIES, CAUSING STRESS CONCENTRATIONS WHICH CAUSED CRACKS DURING THE QUENCHING PROCESS. Recall Details
Problem: THE ENGINE COOLING FAN BLADES MAY BREAK DUE TO INADEQUATE BLADE STRENGTH AROUND THE RIVETS THAT ATTACH THE BLADES TO THE FAN SPIDER. Recall Details
Problem: THE CARRIER YOKE BOLTS WERE MANUFACTURED WITH WORN ROLLING THREAD DIES, CAUSING STRESS CONCENTRATIONS WHICH CAUSED CRACKS DURING THE QUENCHING PROCESS. Recall Details
Problem: THE ENGINE COOLING FAN BLADES MAY BREAK DUE TO INADEQUATE BLADE STRENGTH AROUND THE RIVETS THAT ATTACH THE BLADES TO THE FAN SPIDER. Recall Details
Problem: FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM. Recall Details
Problem: THE DRIVESHAFT CENTER BEARING SUPPORT BRACKET CAN CRACK AND BREAK. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH FONTAINE FIFTH WHEEL ASSEMBLIES. THE FIFTH WHEEL MOUNTING PLATES CAN CRACK. Recall Details
Problem: THE DRIVESHAFT CENTER BEARING SUPPORT BRACKET CAN CRACK AND BREAK. Recall Details
Problem: FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH FONTAINE FIFTH WHEEL ASSEMBLIES. THE FIFTH WHEEL MOUNTING PLATES CAN CRACK. Recall Details
Problem: THE ENGINE COOLING FAN BLADES MAY BREAK DUE TO INADEQUATE BLADE STRENGTH AROUND THE RIVETS THAT ATTACH THE BLADES TO THE FAN SPIDER. Recall Details
Problem: LAP AND SHOULDER SEAT BELT ARRANGEMENT FOR FIXED (NON-SUSPENSION) SEATS DOES NOT MEET THE SEAT BELT LOADING REQUIREMENTS OF FMVSS 210. THE INBOARD CLINCH NUT IN CAB SILL, WHERE THE BUCKLE FOR THE SHOULDER AND LAP BELT IS MOUNTED, PULLED OUT OF THE SILL DURING THE TESTS. CONSEQUENCE OF DEFECT: IF SEAT BELT ANCHIRAGE FAILS, THE SEAT OCCUPANT FACES AN INCREASED RISK OF INJURY IN AN ACCIDENT OR SUDDEN STOP. Recall Details
Problem: FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM. Recall Details
Problem: THE UPPER AND LOWER PINCH BOLT ON THE STEERING PITMAN ARM AND THE LOWER PINCH BOLT CONNECTION ON SHEPHARD POWER GEARS WERE NOT TORQUED CORRECTLY. Recall Details
Problem: LAP AND SHOULDER SEAT BELT ARRANGEMENT FOR FIXED (NON-SUSPENSION) SEATS DOES NOT MEET THE SEAT BELT LOADING REQUIREMENTS OF FMVSS 210. THE INBOARD CLINCH NUT IN CAB SILL, WHERE THE BUCKLE FOR THE SHOULDER AND LAP BELT IS MOUNTED, PULLED OUT OF THE SILL DURING THE TESTS. CONSEQUENCE OF DEFECT: IF SEAT BELT ANCHIRAGE FAILS, THE SEAT OCCUPANT FACES AN INCREASED RISK OF INJURY IN AN ACCIDENT OR SUDDEN STOP. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH FONTAINE FIFTH WHEEL ASSEMBLIES. THE FIFTH WHEEL MOUNTING PLATES CAN CRACK. Recall Details
Problem: THE DRIVESHAFT CENTER BEARING SUPPORT BRACKET CAN CRACK AND BREAK. Recall Details
Problem: FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM. Recall Details
Problem: THE DRIVESHAFT CENTER BEARING SUPPORT BRACKET CAN CRACK AND BREAK. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH FONTAINE FIFTH WHEEL ASSEMBLIES. THE FIFTH WHEEL MOUNTING PLATES CAN CRACK. Recall Details
Problem: THE UPPER AND LOWER PINCH BOLT ON THE STEERING PITMAN ARM AND THE LOWER PINCH BOLT CONNECTION ON SHEPHARD POWER GEARS WERE NOT TORQUED CORRECTLY. Recall Details
Problem: STEERING WHEEL RETAINING NUTS MAY HAVE BEEN IMPROPERLY INSTALLED AND/OR TORQUED. Recall Details
Problem: INTERNAL COMPONENTS OF THE E-12 DUAL CIRCUIT AIR BRAKE VALVES MAY BE MISASSEMBLED SO THAT ONE OF THE TAPERED SNAP RINGS IS UPSIDE DOWN. Recall Details
Problem: LAP AND SHOULDER SEAT BELT ARRANGEMENT FOR FIXED (NON-SUSPENSION) SEATS DOES NOT MEET THE SEAT BELT LOADING REQUIREMENTS OF FMVSS 210. THE INBOARD CLINCH NUT IN CAB SILL, WHERE THE BUCKLE FOR THE SHOULDER AND LAP BELT IS MOUNTED, PULLED OUT OF THE SILL DURING THE TESTS. CONSEQUENCE OF DEFECT: IF SEAT BELT ANCHIRAGE FAILS, THE SEAT OCCUPANT FACES AN INCREASED RISK OF INJURY IN AN ACCIDENT OR SUDDEN STOP. Recall Details
Problem: THE UPPER AND LOWER PINCH BOLT ON THE STEERING PITMAN ARM AND THE LOWER PINCH BOLT CONNECTION ON SHEPHARD POWER GEARS WERE NOT TORQUED CORRECTLY. Recall Details
Problem: STEERING WHEEL RETAINING NUTS MAY HAVE BEEN IMPROPERLY INSTALLED AND/OR TORQUED. Recall Details
Problem: LAP AND SHOULDER SEAT BELT ARRANGEMENT FOR FIXED (NON-SUSPENSION) SEATS DOES NOT MEET THE SEAT BELT LOADING REQUIREMENTS OF FMVSS 210. THE INBOARD CLINCH NUT IN CAB SILL, WHERE THE BUCKLE FOR THE SHOULDER AND LAP BELT IS MOUNTED, PULLED OUT OF THE SILL DURING THE TESTS. CONSEQUENCE OF DEFECT: IF SEAT BELT ANCHIRAGE FAILS, THE SEAT OCCUPANT FACES AN INCREASED RISK OF INJURY IN AN ACCIDENT OR SUDDEN STOP. Recall Details
Problem: VEHICLE DESCRIPTION: HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH FONTAINE FIFTH WHEEL ASSEMBLIES. THE FIFTH WHEEL MOUNTING PLATES CAN CRACK. Recall Details
Problem: FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM. Recall Details
Problem: THE DRIVESHAFT CENTER BEARING SUPPORT BRACKET CAN CRACK AND BREAK. Recall Details
Problem: FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM. Recall Details
|