FORD F-250 Recalls

Apr 27, 1999 – VEHICLE DESCRIPTION: GASOLINE AND DIESEL ENGINE PICKUP TRUCKS EQUIPPED WITH 6" AND 8" BEDS MANUFACTURED FROM JANUARY 5, 1998 THROUGH MARCH 21, 1999, DO NOT NOT FULLY SATISFY THE POST CRASH TEST STATIC ROLLOVER REQUIREMENTS OF FMVSS NO. 301, "FUEL SYSTEM INTEGRITY." SIX ATTACHMENT BOLTS (M12 BOLTS) MAY HAVE BEEN DAMAGED DURING THE 30 MPH FRONT BARRIER TEST ALLOWING THE BOLTS TO SHIFT OR BECOME DETACHED, RESULTING IN FUEL SPILLAGE.

Apr 27, 1999 – VEHICLE DESCRIPTION: PICKUP TRUCKS EQUIPPED WITH 6" BEDS MANUFACTURED FROM JANUARY 5, 1998 THROUGH JUNE 4, 1999, DO NOT NOT FULLY SATISFY THE POST CRASH TEST STATIC ROLLOVER REQUIREMENTS OF FMVSS NO. 301, "FUEL SYSTEM INTEGRITY." CONTACT BETWEEN THE FUEL TANK AND A FUEL TANK LOCATOR BRACKET DURING A FRONT BARRIER IMPACT TEST RESULTED IN A CUT IN THE TANK, RESULTING IN FUEL LEAKAGE.

Mar 30, 1999 – VEHICLE DESCRIPTION: CERTAIN 1997-1999 RHD EXPLORER EQUIPPED WITH 4.0L OHV/SOHC ENGINES AND CRUISE CONTROL BUILT FROM MAY 29, 1996 THROUGH MARCH 4, 1999; 1998-1999 EXPLORER/MOUNTAINEERS EQUIPPED WITH 4.0L OHV/SOHC OR 5.0L ENGINES OR 1998-1999 RANGERS EQUIPPED WITH 2.5L, 3.0L FFV/EFI OR 4.0L ENGINES AND CRUISE CONTROL BUILT FROM JANUARY 5, 1998 THROUGH MARCH 4, 1999; 1998-1999 MUSTANGS EQUIPPED WITH 3.8L, 4.6L 2-VALVE OR 4-VALVE ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999; 1999 F250/F350/F450/F550 (OVER 8,500 LBS.) TRUCKS EQUIPPED WITH 5.4L OR 6.8L ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999; AND 1999 F-53 STRIPPED CHASSIS EQUIPPED WITH 5.4L OR 6.8L ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999. A CRUISE CONTROL CABLE CAN INTERFERE WITH THE SPEED CONTROL SERVO PULLEY AND NOT ALLOW THE THROTTLE TO RETURN TO IDLE WHEN DISENGAGING THE CRUISE CONTROL.

Dec 01, 1998 – VEHICLE DESCRIPTION: LIGHT DUTY TRUCKS. THE CAST TOW HOOKS CHANGES THE CRASH PULSE OF THE VEHICLE IN FRONTAL BARRIER IMPACTS AND THE AIR BAG SENSOR WAS NOT CALIBRATED TO THIS NEW CRASH PULSE WHICH MAY CAUSE THE AIR BAGS TO DEPLOY IN LOWER SPEED IMPACTS THAN DESIGN INTENT.

Aug 24, 1998 – VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS. A SPEED CONTROL CABLE MAY NOT HAVE FULLY SEATED INTO THE ACCELERATOR BRACKET AT TIME OF INSTALLATION. IF THE CABLE IS NOT FULLY SEATED INTO THIS BRACKET, THE CABLE COULD SEPARATE FROM THE BRACKET.

Aug 19, 1998 – VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS. THE FUEL PRESSURE REGULATOR O-RING MAY HAVE BEEN DAMAGED WHEN THE FUEL PRESSURE REGULATOR WAS INSTALLED IN THE ENGINE FUEL RAIL. IF THE O-RING IS DAMAGED, FUEL VAPOR OR LEAKAGE COULD OCCUR.

May 29, 1998 – VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS AND CHASSIS-CABS. ONE OR MORE OF THE FOUR RIVETS ON THE LOWER STEERING SHAFT FLEX COUPLING MAY NOT HAVE BEEN CRIMPED DURING THE SUB-ASSEMBLY PROCESS.

May 13, 1998 – VEHICLE DESCRIPTION: MULTI-PURPOSE VEHICLES AND LIGHT DUTY PICKUP TRUCKS. THE LUG NUTS ON THESE VEHICLES MAY NOT CREATE SUFFICIENT CLAMP LOAD ALLOWING WHEEL MOVEMENT IN RELATION TO THE HUB/ROTOR MOUNTING SURFACE.

Oct 29, 1997 – VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND CHASSIS. THE TIRES ON THESE VEHICLES WERE DAMAGED DURING MOUNTING ONTO THE WHEELS. ONLY TRUCKS PRODUCED AT THE CUAUTITLAN, MEXICO PLANT BETWEEN SEPTEMBER 1, 1996, AND JULY 17, 1997, WERE AFFECTED BY THE DEFECT.

Oct 07, 1997 – VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE PASSENGER VEHICLES. IF THE AUTOMATIC TRANSMISSION SHIFT CABLE ASSEMBLY WAS NOT FULLY ATTACHED TO THE STEERING COLUMN BRACKET, THE SHIFT CABLE ASSEMBLY CAN COME OUT OF THE BRACKET. THE VEHICLE OPERATOR WOULD THEN NOT BE ABLE TO SHIFT THE TRANSMISSION FROM ONE OF THE DRIVE GEAR POSITIONS INTO THE PARK POSITION EVEN THOUGH THE GEAR SHIFT SELECTOR WOULD INDICATE "PARK."