FORD FAIRMONT Recalls

Mar 06, 2008 – INTERCONTINENTAL AUTO PARTS IS RECALLING 1,937 FUEL FILTERS, P/NOS ALG 44/1 AND PUROLATOR F10024, SHIPPED BETWEEN JANUARY 14 AND FEBRUARY 13, 2008, SOLD FOR USE ON THE VEHICLES LISTED ABOVE. THE FILTER'S OUTLET CAP MAY NOT BE SECURELY CRIMPED TO THE HOUSING. THIS COULD RESULT IN A SEPARATION OF FILTER'S OUTLET CAP FROM THE HOUSING.

Aug 27, 2007 – CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

Feb 24, 1983 – THE SHIFT INDICATOR MAY NOT ACCURATELY REFLECT THE SHIFT SELECTOR POSITION. SOME VEHICLES WERE PRODUCED WITH TRANSMISSION CONTROL SELECTOR TUBE RETAINING CLIPS THAT MAY NOT BE HARD ENOUGH. THE CLIP MAY LOOSEN OR FALL OFF, AND THE SELECTOR TUBE MAY BECOME DISPLACED.

Oct 13, 1982 – THE PARK LEVER ON THE INVOLVED VEHICLES CONTAINS A DEFECTIVE SPRING WHICH COULD PREVENT AUTOMATIC ENGAGEMENT OF THE PARKING GEAR.

Nov 19, 1980 – ON SOME OF THE INVOLVED VEHICLES, THE BRAKE PUSHROD TO BRAKE PEDAL RETAINING PINS MAY BE MISSING OR LOOSE. INSECURELY INSTALLED OR MISSING RETAINERS COULD RESULT IN DISENGAGEMENT OF THE BRAKE PUSHROD AND TOTAL LOSS OF SERVICE BRAKING.

Dec 27, 1979 – WINDSHIELDS MAY HAVE BEEN INSTALLED ON THESE VEHICLES WITHOUT THE APPLICATION OF A BUTYL PRIMER ON THE MOUNTING SURFACE OF THE GLAZING. THE PRIMER IS REQUIRED TO ENSURE ADEQUATE RETENTION OF THE WINDSHIELD TO ITS OPENING FLANGE. THIS CONSTITUTES A NON-COMPLIANCE WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING".

Dec 18, 1979 – THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, "HYDRAULIC BRAKE SYSTEMS". REAR AXLE ASSEMBLIES INTENDED FOR OTHER VEHICLES MAY HAVE BEEN INSTALLED IN THE INVOLVED VEHICLES. THE WHEEL CYLINDERS MAY NOT BE THE CORRECT SIZE. THIS COULD AFFECT BRAKING PERFORMANCE.

May 15, 1979 – THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.

Jan 26, 1979 – THE INVOLVED VEHICLES WERE BUILT WITH SAFETY COMPLIANCE CERTIFICATION LABELS THAT CONTAINED INCORRECT GVWR AND GAWR WEIGHT INFORMATION. THE GVWR"S COULD BE OVERSTATED BY UP TO 197 LBS., DUE TO AN ERROR IN THE REPORTING OF INCREMENTAL OPTION WEIGHTS USED TO DERIVE THE GVWR"S AND GAWR"S.

Sep 21, 1978 – THE INVOLVED VEHICLES CONTAIN EMISSION CONTROL SYSTEMS THAT UTILIZE A PULSE AIR REED VALVE TO PERMIT AIR FLOW FROM THE AIR CLEANER TO THE EXHAUST MANIFOLD ON NEGATIVE PRESSURE PULSATIONS. THESE REED VALVES MAY FAIL UNDER COLD WEATHER CONDITIONS, CAUSING A BACKFLOW OF EXHAUST GAS INTO THE AIR CLEANER AND FUEL INDUCTION SYSTEM ON POSITIVE EXHAUST PULSES. THIS CAUSES AN OVERLY RICH AIR/FUEL MIXTURE, REDUCED FUEL ECONOMY AND REDUCED ENGINE PERFORMANCE. CONTINUED VEHICLE OPERATION MAY RESULT IN ENGINE STALLING OR OVERHEATING OF THE EXHAUST SYSTEM.