INTERNATIONAL HARVESTER Recalls

Jul 03, 2000 – VEHICLE DESCRIPTION: SCHOOL AND HEAVY DUTY TRUCKS BUILT WITH BENDIX AIR ABS. THE ABS SENSOR WIRES ON ROTATING PARTS CHAFES WHICH CAN LEAD TO A FALSE SIGNAL BEING SENT TO THE BENDIX ABS ELECTRONIC CONTROL UNIT (ECU).

Jun 06, 2000 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH EATON AUTOSHIFT GEN II TRANSMISSION ASSEMBLIES. DUE TO A SOFTWARE PROBLEM IN THE TRANSMISSION ASSEMBLIES, THE TRANSMISSION WILL SELECT THE WRONG GEAR.

May 23, 2000 – VEHICLE DESCRIPTION: SCHOOL/TRANSIT BUSES AND MEDIUM DUTY TRUCKS. THE CASTINGS USED ON THE POWER STEERING PUMPS WERE NOT BUILT TO MATCH THE ENGINEERING DRAWINGS, RESULTING IN A THIN WALL IN THE PUMP CASTING OR A COMPLETE CONNECTION OF TWO PASSAGES THAT ARE SUPPOSED TO BE SEPARATED TO CONTROL FLUID FLOW. THE FLUID FLOW MAY BE REDUCED TO LESS THAN THE MINIMUM REQUIRED FLOW RATE TO PROVIDE FULL POWER ASSIST TO THE BRAKE SYSTEM WITH LOW ENGINE SPEED.

May 23, 2000 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL CODE 16SCH (LOWER BUNK WEBBING RESTRAINT). INCORRECT BOLTS WERE USED TO HOLD THE BUNK WEBBING RESTRAINT LATCH BRACKETS TO THE BUNK BASE.

Dec 12, 1996 – THESE VEHICLES ARE EQUIPPED WITH A DETROIT DIESEL OPTIMIZED IDLE SYSTEM. IF THE IGNITION IS TURNED ON AND THE FUSE FOR THE ELECTRONIC CONTROL MODULE (ECM) POWER FEED LINE IS REMOVED OR BURNED OUT, UNINTENTIONAL CRANKING OF THE ENGINE WILL OCCUR..

Nov 27, 1996 – VEHICLE DESCRIPTION: SCHOOL BUSES EQUIPPED WITH THE INTERNATIONAL I6 ELECTRONIC ENGINE AND AN EXTRA THICK BUS BODY FLOOR. THE ACCELERATOR PEDAL TO FLOOR CLEARANCE IS APPROXIMATELY 1.2 INCHES WITH A STANDARD BUS BODY FLOOR. HOWEVER, SOME CUSTOMERS ORDERED AN ADDITIONAL 3/4 INCH THICK FLOOR AND EXTRA THICK FLOOR MATS TO SERVE AS INSULATION IN COLD CLIMATES. WHEN THIS EXTRA FLOORING IS USED, THE BOTTOM EDGE OF THE ACCELERATOR PEDAL, WHEN DEPRESSED, CAN COME IN CONTACT WITH THE FLOOR.

Nov 27, 1996 – VEHICLE DESCRIPTION: SCHOOL BUSES AND HEAVY DUTY TRUCKS EQUIPPED WITH REAR AXLE ASSEMBLIES PRODUCED BY DANA SPICER. CERTAIN REAR AXLE ASSEMBLIES WERE IMPROPERLY HEAT TREATED WHICH COULD ALLOW PINION BREAKAGE AT THE PINION THREADS.

Nov 22, 1996 – THE DRIVE AXLE HOUSINGS CONSIST OF A PLATE STEEL CENTER SECTION AND TWO FORGED SPINDLES, ONE OF WHICH IS WELDED TO EACH END OF THE CENTER SECTION. EACH SPINDLE CONTAINS A KEYWAY SLOT IN WHICH THE LOCKING TAB FOR THE WHEEL BEARING NUT LOCKING MECHANISM IS INSERTED. THE LENGTH OF THE KEYWAY SLOT MAY NOT BE LONG ENOUGH TO ACCOMMODATE THE TAB CAUSING THE TAB TO BE DEFORMED OR DAMAGED DURING INSTALLATION.

Nov 12, 1996 – THESE BUSES HAVE A TURN SIGNAL LEVER THAT WILL NOT OPERATE CONSISTENTLY IN THE LANE CHANGE MODE IF THE LEVER IS NOT MOVED TO THE POSITION WHERE RESISTANCE TO MOVEMENT IS FELT.

Sep 13, 1996 – THE WIRING FROM THE ELECTRONIC CONTROL UNIT WAS CONNECTED TO THE WRONG WHEEL SENSOR OR TO THE WRONG BRAKE MODULATOR VALVE. IT IS POSSIBLE THAT EITHER OR BOTH WIRING MAY HAVE OCCURRED AT EITHER THE FRONT OR REAR AXLE OR BOTH AXLES.