INTERNATIONAL Recalls

Aug 25, 2004 – ON CERTAIN TRUCKS, ONLY EIGHT (8) BOLTS WERE INSTALLED IN THE BRAKE GROUP CONNECTION TO THE REAR AXLES. THE BRAKE GROUP, AN ASSEMBLY THAT INCLUDES THE BRAKE SHOES, AIR CHAMBERS, SLACK ADJUSTERS, AND SPIDER, IR NORMALLY ATTACHED TO THE AXLE HOUSING WITH NINE (9) BOLTS.

Aug 25, 2004 – ON CERTAIN TRUCKS, THE FRONT, NON-DRIVE AXLE, COTTER KEYS AND SPINDLE NUT RETAINERS WERE NOT INSTALLED. THE COTTER KEY AND SPINDLE NUT RETAINER PREVENT THE SPINDLE NUT FROM LOOSENING AND THUS AID IN WHEEL RETENTION.

Aug 24, 2004 – CERTAIN 2004 MY INTERNATIONAL CE SCHOOL BUSES AND MEDIUM DUTY TRUCKS EQUIPPED WITH ROBERT BOSCH PARK BRAKE ASSEMBLIES, MANUFACTURED BETWEEN JULY 20 AN AUGUST 5, 2004. THE PARKING BRAKE ASSEMBLY BACKING PLATE WAS INCORRECTLY MACHINED. THIS MAY CAUSE THE PARK BRAKE TO NOT FULLY ENGAGE AND IF THE PARK BRAKE DOES ENGAGE, IT MAY NOT FULLY RELEASE.

Aug 13, 2004 – INTERNATIONAL 2005 MY RE SCHOOL BUSES BUILT FROM MARCH 3 THROUGH AUGUST 5, 2004. THE HIGH-PRESSURE SUPPLY HOSE FROM THE POWER STEERING PUMP TO THE STEERING GEAR MAY CHAFE AGAINST THE POSITIVE STUD ON THE STARTER SOLENOID. THE ENGINE ELECTRICAL HARNESS, CONTAINING THE POSITIVE CABLE FROM THE ALTERNATOR, MAY BE PINCHED BETWEEN THE ENGINE AND THE BUS BODY. AN OPTIONAL OIL PRESSURE SWITCH MAY HAVE BEEN DAMAGED DURING MANUFACTURING, CAUSING A LEAK TO FORM.

Jun 30, 2004 – ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH INTERNATIONAL DT530, CUMMINS, OR CATERPILLAR I-6 ENGINES, THE POSITIVE BATTERY CABLE BETWEEN THE BATTERIES AND THE STARTER MAY RUB AGAINST AN ELECTRICAL GROUND CABLE BETWEEN THE STARTER AND FRAME RAIL.

Jun 30, 2004 – ON CERTAIN HEAVY DUTY TRUCKS, THE ENGINE ELECTRICAL HARNESS CAN CHAFE AGAINST SHARP EDGES ON THE ENGINE.

Jun 03, 2004 – ON CERTAIN SCHOOL BUSES AND TRUCK MODEL VEHICLES MANUFACTURED BETWEEN FEBRUARY 28, 1999, THROUGH APRIL 5, 2004, THE ANTI-LOCK BRAKE SYSTEM ELECTRONIC CONTROL UNIT (ECU) MAY MISINTERPRET A CORRUPT WHEEL SPEED SIGNAL.

May 27, 2004 – ON CERTAIN SCHOOL AND TRANSIT BUSES THE STUDS USED TO SECURE THE POWER STEERING PUMP TO THE ENGINE BLOCK CAN FAIL, RESULTING IN ENGINE OIL LEAKAGE AND COMPLETE LOSS OF POWER STEERING. THE POWER STEERING PUMP IS DESIGNED TO PROVIDE POWER ASSIST TO BOTH THE STEERING SYSTEM AND THE HYDRAULIC BRAKING SYSTEM. SHOULD STUD FAILURE CAUSE THE PUMP TO BECOME DISENGAGED FROM ITS DRIVE GEARS, A REDUCTION OF THE FLUID FLOW RATE TO THE BRAKE SYSTEM COULD OCCUR AND POSSIBLY CAUSE AN EXTENDED STOPPING DISTANCE AS WELL AS INCREASED STEERING WHEEL EFFORTS.

Apr 22, 2004 – CERTAIN TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." THE SEAT BELT LATCH FAILED A QUALITY REVIEW.

Apr 19, 2004 – CERTAIN TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." A STANDARD FITTING WAS INSTALLED IN PLACE OF A SINGLE CHECK VALVE ON THE PARK BRAKE RELAY VALVE.