MACK CL Recalls

Mar 03, 2010 – MACK TRUCKS IS RECALLING CERTAIN MODEL YEAR 2002 THROUGH 2004 CL, CV, LE, MR, RB, RD, AND MODEL YEAR 2003 THROUGH 2004 DM HEAVY TRUCKS MANUFACTURED FROM FEBRUARY 1, 2002 THROUGH SEPTEMBER 30, 2003, EQUIPPED WITH AXLE BEAMS MANUFACTURED BY BHARAT FORGE. THE AXLE BEAM MAY HAVE TRANSVERSE SHEAR LINES ON THE BOTTOM OF THE AXLE FROM THE TRIMMING PROCESS.

Jun 30, 2009 – MACK IS RECALLING 10,300 MODEL YEAR 2004 AND 2005 CL, CV, DM, LE, AND RB AND MODEL YEAR 2004 RD HEAVY TRUCKS MANUFACTURED FROM OCTOBER 1, 2003 THROUGH SEPTEMBER 30, 2004, EQUIPPED WITH AXLE BEAMS MANUFACTURED BY BHARAT FORGE. THE AXLE BEAM MAY HAVE TRANSVERSE SHEAR LINES ON THE BOTTOM OF THE AXLE FROM THE TRIMMING PROCESS.

Oct 23, 2007 – ON CERTAIN TRUCKS EQUIPPED WITH A SAF HOLLAND SIMPLEX FIFTH WHEEL, THE LEVER ARM PIVOT BOLT MAY HAVE BEEN OVER TIGHTENED. AN OVER TIGHTENED PIVOT BOLT CAN DISTORT THE PIVOT BOLT SPACER SLEEVE, WHICH MAY PREVENT THE FIFTH WHEEL LATCH JAW FROM CLOSING AND LATCHING SECURELY AROUND THE TRAILER KING PIN.

Feb 15, 2007 – ON CERTAIN TRUCKS EQUIPPED WITH A 46K POUND CHALMERS REAR SUSPENSION, THE ADJUSTABLE TORQUE RODS USED ON THE SUSPENSION MAY BE BRITTLE.

Jul 26, 2006 – ON CERTAIN TRUCKS EQUIPPED WITH A LEGRIS AIR MANIFOLD, THE BRASS PUSH-TO-CONNECT CARTRIDGE MAY UNEXPECTEDLY SEPARATE FROM THE PLASTIC HOUSING.

Jul 28, 2005 – ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS, THE BOLTS THAT ATTACH THE STEERING GEAR TO THE FRAME MAY NOT BE TIGHTENED PROPERLY.

Jul 07, 2005 – ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH HOLLAND AIR SUSPENSION SYSTEMS, A TRANSVERSE BEAM CASTING MAY FRACTURE UNDER NORMAL LOADS. IF A CASTING BREAKS WHEN THE VEHICLE IS TRAVELING ON A ROADWAY THERE IS THE POTENTIAL FOR PIECES OF THE CASTING TO BECOME PROJECTILES AND THE SUSPENSION'S TRANSVERSE BEAM MAY DROP DOWN LOW ENOUGH TO CONTACT THE ROAD SURFACE.

Jun 07, 2004 – ON CERTAIN CLASS 8 CHASSIS BUILT WITH HENDRICKSON LIFT AXLES WHICH CONTAINED WEBB BRAKE DRUMS, THE BRAKE DRUMS COULD EXPERIENCE PREMATURE CRACK OF THE BRAKING SURFACE RESULTING IN REDUCTION OR COMPLETE LOSS OF BRAKING ON THAT WHEEL END OR LOSS OF BRAKE DRUM PIECES.

Jul 17, 2003 – CERTAIN HEAVY DUTY VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." IMPROPER SEATING OF THE CHECK VALVE RETAINER IN THE BRASS FITTING HOUSING HAS OCCURRED. IT IS POSSIBLE FOR THE AIR BRAKE SYSTEM PRESSURE TO PUSH THE CHECK VALVE INTERNAL PARTS INTO THE PRIMARY SYSTEM RESERVOIR AND A VEHICLE OPERATOR WOULD NOT KNOW THAT THIS HAS HAPPENED.

Aug 15, 2002 – ON SOME HEAVY DUTY CLASS 8 VEHICLES EQUIPPED WITH ARVINMERITOR AXLE ASSEMBLIES WHICH MAY HAVE BEEN MANUFACTURED WITH TRW MODEL 20EDL BALL SOCKETS, THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW SPECIFICATION CASE DEPTH AND/OR HARDNESS WHICH CAN LEAD TO PREMATURE WEAR OUT OF THE SOCKET IN SOME APPLICATIONS.