NISSAN ALTIMA Recalls

Jul 31, 2008 – NISSAN IS RECALLING 1,018 MY 2008 ALTIMA VEHICLES. THE LEFT SIDE FRONT SUSPENSION TRANSVERSE LINK BOLT MAY NOT HAVE BEEN TIGHTENED TO SPECIFICATION. THIS CONDITION COULD CAUSE THE BOLT TO BECOME LOOSE WHILE THE VEHICLE IS BEING DRIVEN.

Dec 28, 2007 – ON CERTAIN PASSENGER VEHICLES THAT HAVE HAD THE BODY CONTROL MODULE (BCM) REPLACED DURING SERVICE AT A DEALERSHIP, THE TIRE PRESSURE MONITORING SYSTEM (TPMS) MAY HAVE BEEN INADVERTENTLY DEACTIVATED DUE TO AN ISSUE WITH THE DEALER SERVICE SOFTWARE. IF THE TPMS IS TURNED OFF, IT WOULD NOT ALERT THE DRIVER TO A DECREASE IN THE TIRE PRESSURE AS DESIGNED.

Nov 14, 2007 – ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANKSHAFT POSITION SENSOR CAN OVERHEAT CAUSING A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.

Oct 25, 2007 – CERTAIN TYC HALOGEN TYPE HEADLAMP ASSEMBLIES P/N 20-6644-00 SOLD AS AFTERMARKET EQUIPMENT FOR 2005-2006 NISSAN ALTIMA PASSENGER VEHICLES. THE PHOTOMETRIC WERE MISALIGNED WHICH DOES NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Sep 14, 2007 – CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Aug 21, 2007 – CERTAIN ANZO AFTERMARKET HEADLIGHTS, P/N 02-AZ-NA02-B-A, SOLD FOR USE ON 2002-2004 NISSAN ALTIMA VEHICLES. DURING PRODUCTION THE LAMP HOUSING SHAPE DEFORMED DISTORTING THE ASSEMBLY ANGLE OF THE REFLECTOR AND INFLUENCED THE AIMING POSITION. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Jul 25, 2007 – CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 315-1145L-AS AND 315-1145R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. DURING PRODUCTION THE LAMP REFLECTOR SHAPE DEFORMED CHANGING THE SHAPE OF THE OPTIC SURFACE. THIS WILL CHANGE THE OPPOSITE POSITION OF LOW BEAM AND HIGH BEAM OPTICSAND CHANGE THE ANGLE OF INCIDENCE AND ILLUMATED LOCATION WHICH FAILS TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Jun 21, 2007 – ON CERTAIN VEHICLES, IF A SUFFICIENTLY HOT OBJECT ENTERS THE AIR FILTER HOUSING THROUGH THE ENGINE FRESH AIR INTAKE SYSTEM AND CONTACTS THE ENGINE AIR FILTER, THE FLAMMABILITY CHARACTERISTICS OF THE AIR FILTER MATERIAL ARE SUCH THAT THE FILTER MAY IGNITE.

Jul 17, 2006 – CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Jul 07, 2006 – ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANK ANGLE SENSOR IS AFFECTED BY TEMPERATURE VARIATIONS. UNDER CERTAIN DRIVING CONDITIONS, THESE VARIATIONS IN TEMPERATURE CAN BE LARGE ENOUGH TO CAUSE A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.