NISSAN Recalls

Sep 18, 2007 – ON CERTAIN VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, KENTUCKY, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, TENNESSEE, VERMONT, VIRGINIA, WEST VIRGINIA , WISCONSIN AND THE DISTRICT OF COLUMBIA, DURING THE COATING PROCESS OF THE FUEL FILLER TUBE ASSEMBLY, AN INSUFFICIENT AMOUNT OF COATING MAY HAVE BEEN APPLIED AT THE LOWER MOUNTING BRACKET. THIS COULD RESULT IN AN OPENING IN THE COATING WHICH CAN ALLOW WATER TO ENTER AND MAKE CONTACT WITH THE BARE METAL OF THE TUBE.

Sep 14, 2007 – CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Aug 27, 2007 – CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

Aug 21, 2007 – CERTAIN ANZO AFTERMARKET HEADLIGHTS, P/N 02-AZ-NA02-B-A, SOLD FOR USE ON 2002-2004 NISSAN ALTIMA VEHICLES. DURING PRODUCTION THE LAMP HOUSING SHAPE DEFORMED DISTORTING THE ASSEMBLY ANGLE OF THE REFLECTOR AND INFLUENCED THE AIMING POSITION. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Jul 25, 2007 – CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 315-1145L-AS AND 315-1145R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. DURING PRODUCTION THE LAMP REFLECTOR SHAPE DEFORMED CHANGING THE SHAPE OF THE OPTIC SURFACE. THIS WILL CHANGE THE OPPOSITE POSITION OF LOW BEAM AND HIGH BEAM OPTICSAND CHANGE THE ANGLE OF INCIDENCE AND ILLUMATED LOCATION WHICH FAILS TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Jul 03, 2007 – CERTAIN HOPKINS AFTERMARKET TRAILER BRAKE CONTROL CONNECTION HARNESSES SOLD FOR USE ON CERTAIN MODELS OF NISSAN VEHICLES WHICH ARE LISTED ABOVE. THE INTERNAL PART NUMBERS WITHIN HOPKINS ARE: 1010476025, 1040376025, 1110476025, 1170376025, 1290376025, 1010476035, 1040376035, 1110476035, 1170376035, AND 1290376035. A WIRE MAY HAVE BEEN PLACED IN AN INCORRECT POSITION IN THE ELECTRICAL CONNECTOR HOUSING. THIS RESULTS IN AN INCORRECT ROUTING OF WIRES BETWEEN THE TRAILER BRAKE CONTROLLER AND THE TOWING VEHICLE WIRING SYSTEM.

Jun 21, 2007 – ON CERTAIN VEHICLES, IF A SUFFICIENTLY HOT OBJECT ENTERS THE AIR FILTER HOUSING THROUGH THE ENGINE FRESH AIR INTAKE SYSTEM AND CONTACTS THE ENGINE AIR FILTER, THE FLAMMABILITY CHARACTERISTICS OF THE AIR FILTER MATERIAL ARE SUCH THAT THE FILTER MAY IGNITE.

Jun 07, 2007 – DURING PRODUCTION, A SELECT NUMBER OF VEHICLES UNDERWENT AN OFFLINE INSPECTION AT THE ASSEMBLY PLANT WHERE A BOLT IN THE FRONT SUSPENSION ASSEMBLY WAS REMOVED. ON SOME OF THESE VEHICLES, IT IS POSSIBLE THAT THIS BOLT MAY NOT HAVE BEEN TIGHTENED TO SPECIFICATION WHEN IT WAS REINSTALLED.

Apr 03, 2007 – ON CERTAIN CREW CAB MODEL TRUCKS, THE SEAT BACK SHAPE MAY BE SUCH THAT THERE MAY NOT BE SUFFICIENT WEBBING ON THE RETRACTOR SPOOL FOR THE REAR CENTER SEAT BELT TO RELEASE FROM THE AUTOMATIC LOCKING MODE (ALR) AFTER IT IS ENGAGED AND THE SEAT BELT IS RETRACTED. IF THIS OCCURS, THERE MAY BE DIFFICULTY IN PULLING THE SEAT BELT OUT OF THE RETRACTOR THUS PREVENTING ITS USAGE.

Mar 12, 2007 – ON CERTAIN HATCHBACK VEHICLES, THE TERMINALS FOR THE PASSENGER SIDE SEAT BELT TENSION SENSOR HARNESS CONNECTOR MAY HAVE BEEN DAMAGED DURING THE MANUFACTURING PROCESS. THIS COULD RESULT IN A LOSS OF ELECTRICAL CONTINUITY CAUSING THE OCCUPANT DETECTION SYSTEM TO BECOME INOPERATIVE.