ON CERTAIN PASSENGER VEHICLES, THE METAL FORMING PART OF THE FRONT CROSSMEMBER MAY HAVE BEEN IMPROPERLY

Sep 06, 2006 — Recall Campaign #06V334000

ON CERTAIN PASSENGER VEHICLES, THE METAL FORMING PART OF THE FRONT CROSSMEMBER MAY HAVE BEEN IMPROPERLY STAMPED RESULTING IN THE METAL BECOMING THINNER IN THE CROSS-SECTION THAN SPECIFIED. THIS COULD, OVER TIME, RESULT IN BREAKAGE OF THE CROSSMEMBER.

The recall was influenced by the manufacturer with about 1,516 units affected.

See recall notice

NHTSA Safety Recall Notice

06V334000

Manufacturer:	Mitsubishi Motors North America, Inc.
Recall date:	September 06, 2006
NHTSA Campaign #:	06V334000
Units affected:	1,516

Description:: ON CERTAIN PASSENGER VEHICLES, THE METAL FORMING PART OF THE FRONT CROSSMEMBER MAY HAVE BEEN IMPROPERLY STAMPED RESULTING IN THE METAL BECOMING THINNER IN THE CROSS-SECTION THAN SPECIFIED. THIS COULD, OVER TIME, RESULT IN BREAKAGE OF THE CROSSMEMBER.
Consequeces:: BREAKAGE OF THE CROSSMEMBER MAY ALLOW SEPARATION OF THE PASSENGER SIDE LOWER CONTROL ARM, WHICH MAY RESULT IN THE LOSS OF STEERING CONTROL INCREASING THE RISK OF A CRASH.
Corrective action:: DEALERS WILL INSPECT AND REPLACE THE CROSSMEMBER FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 21, 2006. OWNERS MAY CONTACT MITSUBISHI AT 888-648-7820.
Notes:: MITSUBISHI RECALL NO. SR-06-004.CUSTOMERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO HTTP://WWW.SAFERCAR.GOV.

Affects the following:

2007 MITSUBISHI ECLIPSE Complaints
With my vehicle the brakes go straight to the floor. I took it to the mitsubishi dealership closest to me (Bobmills mitsubishi Jacksonville Nc). When I got there i told them what was going on, and if you bleed the brakes they worked fine for 3 or 4 days but after that the brakes would just go to the floor again. They said they bleed the brakes to replace the fluid and then tested the ABS module for a recall and said it was fine but I had a collapsed brake line in the rear. I replaced all the brake lines on the vehicle and did a complete bleed again to remove any air. The brakes now go all the way to the floor again. I was trying to bleed them just to see if I could get some pressure, but 3 of the lines aren't getting pressure. I decided to check and bleed at the master cylinder, I had plenty of pressure coming out so I know that's good. Then I checked the bleed pressure at the ABS module thats on the recall and I am only getting pressure from the drivers front tire, the other 3 are not giving pressure at all, even if you pump the brakes while they are open. So I know the cylinders in that ABS module are bad. So I called the dealership again and they are refusing to do it because they said they don't work on vehicles that old.;
2007 MITSUBISHI ECLIPSE SPYDER Complaints
TL* THE CONTACT OWNS A 2007 MITSUBISHI ECLIPSE SPYDER. WHILE THE CONTACT'S DAUGHTER WAS DRIVING 30 MPH, THE DRIVER DEPRESSED THE BRAKE PEDAL, BUT THE BRAKES FAILED. AS A RESULT, THE DRIVER STRUCK THE REAR OF ANOTHER VEHICLE. THE AIR BAGS FAILED TO DEPLOY. THE DRIVER SUSTAINED INJURIES TO THE HEAD, NECK, AND SPINE AND LOST CONSCIOUSNESS. MEDICAL ATTENTION WAS REQUIRED AND THE DRIVER WAS TAKEN TO THE HOSPITAL. A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED TO A COLLISION CENTER. THE VEHICLE WAS NOT DIAGNOSED. THE CONTACT WAS UNSURE IF THE VEHICLE COULD BE REPAIRED OR WAS DESTROYED. A DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND MADE VARIOUS ATTEMPTS TO CONTACT THE DRIVER. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 15V337000 (SERVICE BRAKES, HYDRAULIC). THE APPROXIMATE FAILURE MILEAGE WAS 112,000.;