VEHICLE DESCRIPTION: CLASS A MOTOR HOMES. THESE MOTOR HOMES

Jan 26, 1999 — Recall Campaign #99V013000

VEHICLE DESCRIPTION: CLASS A MOTOR HOMES. THESE MOTOR HOMES, WHEN FULLY EQUIPPED AND LOADED WITH TYPICAL CARGO, WILL EXPERIENCE AN OVERLOADED CONDITION ON THE REAR AXLE.

The recall was influenced by the manufacturer with about 95 units affected.

See recall notice

NHTSA Safety Recall Notice

99V013000

Manufacturer:	FLEETWOOD ENTERPRISES, INC.
Recall date:	January 26, 1999
NHTSA Campaign #:	99V013000
Units affected:	95

Description:: VEHICLE DESCRIPTION: CLASS A MOTOR HOMES. THESE MOTOR HOMES, WHEN FULLY EQUIPPED AND LOADED WITH TYPICAL CARGO, WILL EXPERIENCE AN OVERLOADED CONDITION ON THE REAR AXLE.
Consequeces:: THIS COULD CAUSE THE REAR AXLE COMPONENTS TO FAIL PREMATURELY RESULTING IN LOSS OF VEHICLE CONTROL.
Corrective action:: DEALERS WILL REPLACE THE REAR AXLE WITH A NEW HIGHER CAPACITY REAR AXLE.
Notes:: OWNER NOTIFICATION BEGAN APRIL 5, 1999.OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FLEETWOOD AT 1-800-322-8216. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).

Affects the following:

1998 FLEETWOOD BOUNDER

1998 FLEETWOOD BOUNDER Complaints
I OWN AND OPERATE A GENERAL REPAIR SHOP. MY TECH REPLACED FRONT WHEEL ABS SENSORS ON FOR MENTIONED VEHICLE. WORKHORSE MFG PART NUMBERS (W8006778) AND (W8006803). WHILE ON TEST DRIVE THE ABS SYSTEM ENTERED FALSE DEPLOYMENT MODE AT 15MPH WHILE APPROACHING A BUSY HIGHWAY INTERSECTION. I HAD TO STAND ON THE BRAKE PEDAL WITH BOTH FEET AND SLAM THE TRANSMISSION INTO LOW TO BRING THE VEHICLE TO STOP. THE NOSE OF THE COACH ENDED BLOCKING HALF A LANE OF TRAFFIC. NO ACCIDENT. FYI, THIS VEHICLE GVW IS 20,000 LBS. ( NOTE: THE FOLLOWING IS TECHNICAL IN NATURE.) I DROVE THE VEHICLE BACK TO THE SHOP TO INITIATE INVESTIGATION. USING A DVOM I MEASURED THE VOLTAGE AMPLITUDE OUT OF THE NEW WHEEL SPEED SENSORS. THE FRONT LEFT MEASURED .068V AC AND THE FRONT RIGHT MEASURED .286V AC. THIS IS THE CAUSE OF THE FALSE DEPLOYMENT. I THEN REMOVED THE FRONT WHEELS TO INSPECT THE SENSORS AND DISCOVERED THE SOURCE OF THE FAILURE. THE REPLACEMENT SENSORS ARE MANUFACTURE WITHOUT LOCATION DOWELS. THE LOCATION DOWELS SET THE CRITICAL CLEARANCE GAP BETWEEN THE RELUCTOR AND SENSOR. THIS CLEARANCE GAP HAS A NARROW PLUS OR MINUS TOLERANCE. WHEN THE TOLERANCE IS LOST THE ABS SYSTEM WILL ENTER A FALSE DEPLOYMENT MODE ( ABS SYSTEM ACTIVATES AND BLOCKS BRAKE FLUID PRESSURE BEING APPLIED TO THE BRAKE CALIPERS ). THE NEW REPLACEMENT ABS SENSORS HAVE NO LOCATION DOWELS THERE FOR TOLERANCES AS DESIGNED ARE NOT ACHIEVED. THIS IS WHY I LOST CONTROL OF 10 TONS OF VEHICLE. THE PART SUPPLIER, PART MANUFACTURER, AND CHASSIS BUILDER HAVE BEEN SERVED FULL NOTICE OF THIS FLAW. THE GM CASE REFERENCE NUMBER IS [XXX]. THANK YOU, [XXX] MASTER ASE TRUCK CERTIFIED MASTER ASE CAR CERTIFIED MASTER ASE ENGINE MACHINIST CERTIFIED ASE L1 CERTIFIED WALWORTH COUNTY CIRCUIT COURT APPOINTED EXPERT WITNESS INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR;