AMERICAN MOTORS CONCORD Recalls

Apr 30, 2009 – FEDERAL-MOGUL CORPORATION IS RECALLING 2,790 MECHANICAL FUEL PUMPS, P/NO. M6737 SOLD UNDER CARTER AND NAPA BRANDS AND P/NO. 2M6737 SOLD UNDER ACCU-FLOW AND TRU-FLOW BRANDS SHIPPED BETWEEN AUGUST 2008 AND MARCH 2009 FOR USE AS REPLACEMENT EQUIPMENT FOR THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM ROD IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY MANUFACTURED. IMPROPERLY MANUFACTURED PUMP DIAPHRAGM RODS MAY CAUSE THE PUMP TO PRODUCE EXCESS PRESSURE.

Aug 27, 2007 – CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.

Dec 13, 1982 – ORIGINAL PRODUCTION TRANSMISSION LUBRICANT USED IN THE INVOLVED VEHICLES, MAY NOT PROVIDE ADEQUATE LUBRICATION TO PROTECT THE TRANSMISSION"S FIRST GEAR.

May 24, 1982 – ON CERTAIN VEHICLES THE WINDSHIELD IS NOT PROPERLY INSTALLED. THE ADHESION BETWEEN THE WINDSHIELD GLASS AND URETHANE SEALING IS INCOMPLETE. THIS FAILS TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING".

Sep 22, 1981 – THE UNDERHOOD WIRING HARNESS AND VENTILATING HOSE MAY HAVE BEEN MISROUTED DURING VEHICLE ASSEMBLY. MISROUTING MAY CAUSE CHAFING BETWEEN THE HARNESS AND VARIOUS OTHER COMPONENTS, RESULTING IN SHORT CIRCUITS AND MALFUNCTION OF ELECTRICAL ACCESSORIES. THE SWITCH WHICH ACTIVATES THE ENGINE OIL PRESSURE WARNING LIGHT MAY NOT FUNCTION. THE CRANKCASE VENTILATION HOSE MAY BE TOO CLOSE TO THE AIR INJECTION MANIFOLD TUBE AND COULD BE DAMAGED IF ENGINE OVERHEATS.

Jul 06, 1981 – THE CRUISE COMMAND ACTUATION CHAIN MAY CATCH ON THE THROTTLE LINKAGE, CAUSING THE THROTTLE TO REMAIN IN A PARTIALLY OPEN POSITION.

Jan 04, 1981 – THE LEFT OR RIGHT FRONT SAFETY BELT ASSEMBLY MAY HAVE BEEN INSTALLED ON THE INCORRECT SIDE OF THE VEHICLE. THE SHOULDER BELT LOCKING MECHANISM MAY NOT FUNCTION UNDER RAPID DECELERATION. UNDER HARD BRAKING APPLICATIONS OR IN A COLLISION, THE SHOULDER PORTION OF THE SEAT BELT SYSTEM MAY FAIL TO PROPERLY RESTRAIN THE PASSENGER. THERE IS INCREASED RISK OF INJURY TO PASSENGERS WHO MAY CONTACT OTHER OBJECTS UNDER THESE CIRCUMSTANCES.

Aug 28, 1979 – AN IMPROPER BULB SOCKET MAY EXIST IN THE TAIL LAMP ASSEMBLY. THIS MAY CAUSE AN UNACCEPTABLE DECREASE IN BRIGHTNESS LEVELS IN LAMPS USED FOR REAR SIGNALING.

Jan 30, 1979 – INFORMATION ON TIRE AIR PRESSURE PLACARDS ON THE INVOLVED VEHICLES MAY BE INCORRECT. THIS DOES NOT CONFORM WITH FEDERAL MOTOR SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS".

Oct 18, 1978 – THE MANUAL LOCK RELEASE LEVER ON THE SPLIT-BACK BENCH ASSEMBLIES MAY HAVE BEEN BENT DURING ASSEMBLY. THIS BENT CONDITION COULD PREVENT THE INERTIA SEAT LOCK ASSEMBLY FROM FUNCTIONING AUTOMATICALLY. AS A RESULT, THE FRONT SEAT BACK MAY NOT LOCK IN THE UPRIGHT POSITION IF THE CAR IS MOVING FORWARD AND BROUGHT TO AN ABRUPT STOP.