CHEVROLET CAMARO Recalls

Oct 24, 2007 – CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

Mar 12, 2007 – CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

Jul 17, 2006 – CERTAIN AJ MOTORSPORT COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

May 19, 2006 – CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

Mar 23, 2006 – CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Dec 12, 2001 – VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION," AND NO. 214, "SIDE IMPACT PROTECTION." THESE VEHICLES MAY HAVE WELDS NEAR THE LOWER DRIVER'S SIDE DOOR HINGE THAT DO NOT MEET SPECIFICATIONS.

Aug 27, 1999 – VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH MANUAL TRANSMISSIONS. THE CLUTCH MASTER CYLINDER MAY HAVE BEEN BUILT WITH AN INCORRECT RETAINING RING.

Nov 04, 1996 – THESE VEHICLES WERE MANUFACTURED WITH SEAT BELT RETRACTORS OUT OF DESIGN POSITION WHICH CAN CAUSE THE RETRACTOR TO LOCK-UP ON SLOPES LESS SEVERE THAN THE FMVSS REQUIREMENT. THIS DOES NOT COMPLY WITH FMVSS NO. 209, "SEAT BELT ASSEMBLIES."

Mar 22, 1995 – THE STEERING INTERMEDIATE SHAFT COULD HAVE BEEN IMPROPERLY ASSEMBLED CAUSING THE SHAFT LOWER COUPLING TO LOOSEN AND ROTATE ON THE STEERING GEAR INPUT SHAFT.

Apr 25, 1994 – THE FUEL FILLER NECK SOLDER JOINT CAN DEVELOP CRACKS OR PIN HOLE LEAKS, WHICH DOES NOT COMPLY WITH FMVSS NO. 301, "FUEL SYSTEM INTEGRITY." THE CRACKS AND HOLES CAN ALLOW FUEL VAPOR AND FUEL LEAKAGE.