FORD FORD Recalls

May 31, 2016 – Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Mar 23, 2010 – VAN-CON HAS NOTIFIED NHTSA OF A DEFECT IN CERTAIN MODEL YEAR 2008-2009 HANDICAP SCHOOL BUSES BUILT ON FORD AND CHEVY CHASSIS, FITTED WITH RICON PUBLIC USE LIFTS. THE RESTRAINT BELT ON THESE LIFTS WAS DESIGNED TO PREVENT THE LIFT FROM MOVING, UNLESS THE TONGUE OF THE BELT IS FULLY ENGAGED AND LATCHED IN THE BUCKLE. RICON HAS DISCOVERED, HOWEVER, THAT IT IS POSSIBLE FOR THE OPERATOR TO INSERT THE BELT TONGUE INTO THE BUCKLE WITHOUT FULLY ENGAGING THE LATCHING MECHANISM. IN THIS CASE, THE RESTRAINT BELT WOULD APPEAR TO BE LATCHED, AND THE OPERATOR COULD RUN THE LIFT. IF THE RESTRAINT BELT TONGUE IS NOT FULLY ENGAGED INTO THE RESTRAINT BELT BUCKLE, AND LATCHED, THE LIFT MAY OPERATE WITH AN OCCUPANT ON THE PLATFORM.

Jan 12, 1981 – THIS IS A MANUFACTURER"S NOTICE TO ADVISE OWNERS OF PROPER VEHICLE OPERATION. THE PARKING GEAR MAY NOT BE SECURELY ENGAGED AFTER THE OPERATOR HAS ATTEMPTED TO SHIFT TO PARK. THE VEHICLE MAY APPEAR TO BE IN PARK THOUGH ACTUALLY IN REVERSE. THIS COULD ALLOW THE VEHICLE TO MOVE UNEXPECTEDLY.

Aug 06, 1980 – SOME OF THE ENGINE COOLING FANS ON THE INVOLVED VEHICLES MAY BE SUBJECT TO HIGH BLADE STRESSES THAT CAN RESULT FROM RESONANT VIBRATION INPUTS OCCURRING DURING NORMAL VEHICLE OPERATION.

Sep 23, 1977 – SOME OF THE INVOLVED VEHICLES MAY HAVE DEFECTIVE CARBURETORS IN WHICH, UNDER CERTAIN CIRCUMSTANCES, THE SECONDARY THROTTLE PLATES MAY STICK OPEN.

Aug 16, 1977 – THE ENGINE FAN BLADES ON THE INVOLVED VEHICLES MAY BE SUBJECT TO CRACKING DUE TO STRESSES GENERATED DURING NORMAL OPERATION. BLADES MAY FRACTURE AND FRAGMENTS WOULD BE PROPELLED FROM THE ROTATING FAN.

Jan 27, 1977 – THE FRONT WHEEL SPINDLE ON THE INVOLVED VEHICLES MAY CRACK IN SERVICE. SPINDLE STEM SEPARATION COULD OCCUR DUE TO FAILURE OF THE STEM AT THE INNER BEARING FILLET LOCATION.

Jun 29, 1972 – THE SHOULDER BELT PIN CONNECTOR PLASTIC SLEEVES WHICH WERE INJECTION MOLDED CAN HAVE SURFACE IMPERFECTIONS OR DISCONTINUITIES AT THE POINT AT WHICH THERMAL PLASTIC IS INJECTED INTO MOLD AND WHERE FLOW DIVERGES TO FILL BOTH SIDES OF THE RING. IF THE CONDITION EXISTS AND THE SLEEVE BREAKS AWAY FROM THE PIN, THE SHOULDER BELT WILL NOT REMAIN ENGAGED TO THE SEAT BELT BUCKLE.