IC BUS RE Recalls

Aug 27, 2008 – NAVISTAR IS RECALLING 1,607 MY 2007 THROUGH 2009 IC BESB, CESB, FESB, AND RESB SCHOOL BUSES MANUFACTURED FROM JANUARY 4, 2006 THROUGH NOVEMBER 15, 2007, EQUIPPED WITH RICON S OR K SERIES WHEELCHAIR LIFTS. THE ANTI-STOW INTERLOCK MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER. THE PRESSURE SENSING SWITCH THAT DETECTS THE PRESENCE OF WEIGHT ON THE PLATFORM WAS NOT ADJUSTED TO THE NECESSARY SENSITIVITY LEVEL. THE LIFT COULD STOW EVEN THOUGH SOMEONE OR SOMETHING IS STILL ON THE LIFT WHICH FAILS TO COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 403, "PLATFORM LIFT SYSTEMS FOR MOTOR VEHICLES."

Jul 30, 2008 – NAVISTAR IS RECALLING 24,975 MY 2003 THROUGH 2008 IC BE, CE, HC, AND RE SCHOOL AND COMMERCIAL BUSES AND 2002 THROUGH 2008 INTERNATIONAL 3200 AND 3300 MODEL BUSES MANUFACTURED BETWEEN SEPTEMBER 21, 2001 THROUGH DECEMBER 14, 2007, EQUIPPED WITH INTERNATIONAL VT365 ENGINES. THESE VEHICLES MAY EXHIBIT ENGINE HARD START, NO START, OR STALL CONDITIONS DUE TO POSSIBLY DAMAGED TERMINALS IN THE FUSE HOLDER CONNECTOR OF THE INJECTOR DRIVE MODULE (IDM) CLEAN BATTERY POWER CIRCUITS. THE TERMINALS MAY HAVE BEEN DAMAGED DURING ELECTRICAL CONTINUITY TESTING IN THE MANUFACTURING PROCESS.

Jul 30, 2008 – NAVISTAR IS RECALLING 1,765 MY 1998 THROUGH 2003 RE SCHOOL AND COMMERCIAL BUSES MANUFACTURED BETWEEN JANUARY 5, 1998 AND JULY 23, 2002, EQUIPPED WITH INTERNATIONAL T444E ENGINES. THE HOSE ASSEMBLIES THAT SUPPLY HIGH PRESSURE OIL TO THE ENGINE'S CYLINDER HEADS MAY DETERIORATE AND ALLOW OIL TO LEAK OR MIST IN THE ENGINE COMPARTMENT.

Feb 27, 2008 – INTERNATIONAL IS RECALLING 34,993 MY 2006-2008 SCHOOL AND TRANSIT BUSES AND HEAVY DUTY TRUCKS/TRACTORS MANUFACTURED BETWEEN JUNE 1, 2006 AND JUNE 28, 2007, EQUIPPED WITH INTERNATIONAL DT466 OR DT570 ENGINES. THE BASE PLATE OF THE ENGINE OIL COOLER MAY CRACK ALLOWING PRESSURIZED OIL TO LEAK INTO THE ENGINE COMPARTMENT.

Jan 09, 2008 – INTERNATIONAL IS RECALLING 1,027 MY 2006-2007 BE, CE, FE, AND RE SCHOOL AND COMMERCIAL BUSES MANUFACTURED FROM JULY 11, 2005 THROUGH JULY 31, 2006, AND EQUIPPED WITH BRAUN PLATFORM LIFTS FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 404, "PLATFORM LIFT INSTALLATIONS IN MOTOR VEHICLES." A PASSENGER CAN APPROACH THE EXPOSED LIFT DOORWAY WITHOUT THE AUDIBLE ALARM ALERTING THEM OF THEIR PROXIMITY TO THE THRESHOLD.

Jun 07, 2007 – CERTAIN MY 1996 THRU 2004 RE COMMERCIAL AND SCHOOL BUSES EQUIPPED WITH INTERNATIONAL T444E V-8 DIESEL ENGINES MANUFACTURED BETWEEN JANUARY 3, 1996, AND MARCH 22, 2004. HOSE ASSEMBLIES THAT SUPPLY HIGH PRESSURE OIL TO THE ENGINE'S CYLINDER HEADS MAY DETERIORATE OVER TIME AND ALLOW OIL TO LEAK OR MIST THE ENGINE COMPARTMENT.

Jun 01, 2007 – CERTAIN MY 2007 AND 2008 INTERNATIONAL SCHOOL AND COMMERCIAL BUSES MANUFACTURED BETWEEN JANUARY 20 AND SEPTEMBER 28, 2006, EQUIPPED WITH RICON WHEELCHAIR LIFTS . THE LIFT INNER BARRIER INTERLOCK SWITCH SYSTEM MAY NOT DETECT THE PRESENCE OF A PASSENGER ON THE INNER BARRIER AND ALLOW THE PLATFORM TO MOVE DOWN MORE THAN ONE INCH BELOW FLOOR LEVEL WHILE OCCUPIED WHICH DOES NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 403, PLATFORM LIFT SYSTEMS FOR MOTOR VEHICLES.

Feb 23, 2007 – CERTAIN MY 2004-2007 IC CE, RE, AND FE COMMERCIAL AND SCHOOL BUSES MANUFACTURED BETWEEN MARCH 12, 2004, AND NOVEMBER 29, 2006. THE SIDE EMERGENCY DOOR HOLDBACK MECHANISM MAY NOT BE INSTALLED IN THE PROPER LOCATION. THIS MAY CAUSE THE MECHANISM TO HOLD THE DOOR IN THE CLOSED POSITION.

Feb 05, 2007 – CERTAIN 2007 AND 2008 MY IC SCHOOL BUSES MANUFACTURED BETWEEN JANUARY 18, 2006, AND JANUARY 17, 2007. THE AIR SUPPLY FITTING MAY SEPARATE FROM THE BASE PLATE, PREVENTING ACTUATION AIR FROM REACHING THE STOP ARM AND/OR CROSSING ARM. THIS CONDITION WILL RESULT IN NON-DEPLOYMENT OF THE STOP ARM AND/OR CROSSING ARM DURING A SCHOOL BUS STOP TO PICK-UP OR DISCHARGE PASSENGERS.

Dec 21, 2006 – CERTAIN IC SCHOOL AND COMMERCIAL BUSES MANUFACTURED BETWEEN OCTOBER 11, 2005, AND OCTOBER 31, 2006. THESE BUSES HAVE THE FOLLOWING SAFETY ISSUES: IF THE DRIVER'S SEAT IS IN THE HIGHEST AND MOST REAR POSITION, THE BACK OF THE SEAT MAY LEAN AGAINST A BARRIER BEHIND THE SEAT, OR AGAINST THE SEAT BACK. THIS WILL PREVENT THE SEAT BELT FROM RETRACTING WHICH FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, SEAT BELT ASSEMBLIES. WHEN ADJUST THE SEAT TO A HIGHER POSITION, THE DRIVER MAY PULL THE SEAT PAST THE LAST STOP SO THAT THE SEAT SITS ON THE ADJUSTING PIN, WHICH ALLOWS THE SEAT TO TEETER ON TOP OF THE PIN. IF OVER-TRAVEL OCCURS, THE UPPER SEAT PEDESTAL TUBE COULD SEPARATE FROM THE LOWER PEDESTAL TUBE DURING VEHICLE OPERATION. IF THE DRIVER IS SITTING IN THE DRIVER'S SEAT AND REACHES TO ADJUST THE SEAT HEIGHT, THEIR WEIGHT WILL CAUSE THE SEAT TO DROP, WHICH COULD RESULT IN THEIR HAND BEING PINCHED BETWEEN THE SEAT AND THE LEVER. THE DRIVER'S SEAT IS DIFFICULT TO ADJUST TO A HIGHER POSITION BECAUSE OF THE ADDITIONAL WEIGHT OF THE ALL BELTS TO SEAT (ABTS) DESIGN.