IC CE Recalls

Dec 17, 2008 – KINGMOR SUPPLY, INC., IS RECALLING 30 RICON WHEELCHAIR LIFTS WHICH IT INSTALLED ON CERTAIN MY 2005 THROUGH 2008 IC CESB SCHOOL BUSES. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 404, "PLATFORM LIFT INSTALLATIONS IN MOTOR VEHICLES." THE ANTI-STOW INTERLOCK MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER. THE PRESSURE SENSING SWITCH THAT DETECTS THE PRESENCE OF WEIGHT ON THE PLATFORM WAS NOT ADJUSTED TO THE NECESSARY SENSITIVITY LEVEL. THE LIFT COULD STOW EVEN THOUGH SOMEONE OR SOMETHING IS STILL ON THE LIFT.

Jul 30, 2008 – NAVISTAR IS RECALLING 24,975 MY 2003 THROUGH 2008 IC BE, CE, HC, AND RE SCHOOL AND COMMERCIAL BUSES AND 2002 THROUGH 2008 INTERNATIONAL 3200 AND 3300 MODEL BUSES MANUFACTURED BETWEEN SEPTEMBER 21, 2001 THROUGH DECEMBER 14, 2007, EQUIPPED WITH INTERNATIONAL VT365 ENGINES. THESE VEHICLES MAY EXHIBIT ENGINE HARD START, NO START, OR STALL CONDITIONS DUE TO POSSIBLY DAMAGED TERMINALS IN THE FUSE HOLDER CONNECTOR OF THE INJECTOR DRIVE MODULE (IDM) CLEAN BATTERY POWER CIRCUITS. THE TERMINALS MAY HAVE BEEN DAMAGED DURING ELECTRICAL CONTINUITY TESTING IN THE MANUFACTURING PROCESS.

Jun 05, 2008 – NAVISTAR IS RECALLING 51,588 HEAVY TRUCKS, COMMERCIAL BUSES AND SCHOOL BUSES MANUFACTURED BETWEEN NOVEMBER 21, 2000 AND MAY 21, 2008, EQUIPPED WITH ONE OR MORE REMOTE POWER MODULES. THE POTTING MATERIAL THAT ENCAPSULATES THE CIRCUIT BOARD OF THE VEHICLE'S REMOTE POWER MODULE MAY NOT SUFFICIENTLY SEAL THE CIRCUIT BOARD FROM WATER AND CONTAMINATION INTRUSION. IF THE ENCAPSULATION IS COMPROMISED, WATER AND CONTAMINANTS MAY CAUSE AN INTERNAL ELECTRICAL SHORT, POSSIBLY RESULTING IN A FIRE.

Jun 02, 2006 – CERTAIN MY 2004 THROUGH 2007 CE AND BE SCHOOL BUSES AND 1300 AND 3300 MODEL VEHICLE CHASSIS MANUFACTURED BY IC CORPORATION BETWEEN MARCH 17, 2004, AND MAY 15, 2006. THE PARK BRAKE SYSTEM MAY ACTIVATE WHILE THE VEHICLE IS UNDER NORMAL OPERATION. ALTHOUGH THE VEHICLE IS BROUGHT TO A STOP, THE ACTIVATION MAY OCCUR WITHOUT WARNING OR INPUT FROM THE DRIVER AND MAY STRAND THE VEHICLE IN AN ACTIVE LANE. THE SPRING APPLIED, HYDRAULIC RELEASE (SAHR) PARK BRAKE ACTUATOR COULD EXPERIENCE A HYDRAULIC LOCK CONDITION THAT WILL NOT ALLOW THE PARK BRAKE TO APPLY.

Dec 20, 2005 – CERTAIN 2005-2007 CE AND MY 2007 BE SCHOOL AND TRANSIT BUSES MANUFACTURED BETWEEN FEBRUARY 10, 2004, AND DECEMBER 15, 2005. PASSENGER COAT STRINGS OR CARRY ON ITEMS CAN GET CAUGHT BETWEEN THE DOOR CONTROL BRACKET AND THE DOOR CONTROL ARM AS THE PASSENGER EXITS THE BUS.

Mar 30, 2005 – CERTAIN 2004-2006 MY IC CORPORATION CE, FE, AND RE SCHOOL BUSES MANUFACTURED FROM MAY 12, 2003, THROUGH MARCH 2, 2005, EQUIPPED WITH CHILD RESTRAINT ANCHORAGE SYSTEMS. THE DIAMETER LATCH ATTACHMENT BARS EXCEED THE DIAMETER REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, CHILD RESTRAINT ANCHORAGE SYSTEMS, WHICH MAY MAKE IT DIFFICULT TO USE WITH FUTURE CAR SEAT ATTACHMENTS. IN ADDITION, SOME OF THE LATCH ATTACHMENTS ARE LOCATED TOO FAR FORWARD OF THE SEAT BACK.

Mar 28, 2005 – CERTAIN 2003-2006 MY IC CE, FE, AND RE SCHOOL BUSES AND RE COMMERCIAL BUSES MANUFACTURED BETWEEN FEBRUARY 4, 2003, AND MARCH 1, 2005, AND EQUIPPED WITH WEBASTO COOLANT HEATERS. THE STAINLESS STEEL WALLS OF THE BURNER TUBES INCORPORATED INTO WEBASTO COOLANT HEATERS MAY BE MADE OF A MATERIAL THAT IS NOT WITHIN SPECIFICATION AND MAY FAIL PREMATURELY.

Feb 07, 2005 – CERTAIN IC CE 2005 SCHOOL BUSES MANUFACTURED BETWEEN APRIL 27 AND OCTOBER 13, 2004. THE LOCKNUT THAT SECURES THE HYDRAULIC BRAKE PIVOT BOLT MAY NOT BE TORQUED PROPERLY.

Oct 28, 2004 – CERTAIN 1998, 2000-2005 MY CE, FE, AND RE SCHOOL BUSES BUILT WITH ONE OR MORE CE WHITE 30-INCH CHILD RESTRAINT SEATS AND MANUFACTURED BETWEEN MARCH 25, 1998 AND AUGUST 24, 2004. THE SEAT CUSHION RETENTION MAY NOT RETAIN THE SEAT IN ALL CIRCUMSTANCES.

Sep 21, 2004 – CERTAIN MY 2001-2005 AMTRAN/IC CORPORATION CE, FE, AND RE SCHOOL BUSES EQUIPPED WITH SURE-LOK WHEELCHAIR TIE-DOWN SECUREMENT ASSEMBLIES P/N 8625-13. THE SPROCKET TEETH OF THE RETRACTOR ASSEMBLY MAY BE OUT OF ALIGNMENT CAUSING THE LOAD PAWL NOT TO FULLY SEAT IN THE SPROCKET TEETH.