IC RE Recalls

Dec 21, 2006 – CERTAIN IC SCHOOL AND COMMERCIAL BUSES MANUFACTURED BETWEEN OCTOBER 11, 2005, AND OCTOBER 31, 2006. THESE BUSES HAVE THE FOLLOWING SAFETY ISSUES: IF THE DRIVER'S SEAT IS IN THE HIGHEST AND MOST REAR POSITION, THE BACK OF THE SEAT MAY LEAN AGAINST A BARRIER BEHIND THE SEAT, OR AGAINST THE SEAT BACK. THIS WILL PREVENT THE SEAT BELT FROM RETRACTING WHICH FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, SEAT BELT ASSEMBLIES. WHEN ADJUST THE SEAT TO A HIGHER POSITION, THE DRIVER MAY PULL THE SEAT PAST THE LAST STOP SO THAT THE SEAT SITS ON THE ADJUSTING PIN, WHICH ALLOWS THE SEAT TO TEETER ON TOP OF THE PIN. IF OVER-TRAVEL OCCURS, THE UPPER SEAT PEDESTAL TUBE COULD SEPARATE FROM THE LOWER PEDESTAL TUBE DURING VEHICLE OPERATION. IF THE DRIVER IS SITTING IN THE DRIVER'S SEAT AND REACHES TO ADJUST THE SEAT HEIGHT, THEIR WEIGHT WILL CAUSE THE SEAT TO DROP, WHICH COULD RESULT IN THEIR HAND BEING PINCHED BETWEEN THE SEAT AND THE LEVER. THE DRIVER'S SEAT IS DIFFICULT TO ADJUST TO A HIGHER POSITION BECAUSE OF THE ADDITIONAL WEIGHT OF THE ALL BELTS TO SEAT (ABTS) DESIGN.

Nov 10, 2005 – CERTAIN 2006 IC RESB (PB305) AND RECB (PC305) SCHOOL AND COMMERCIAL BUSES MANUFACTURED FROM JULY 20 TO OCTOBER 17, 2005. THE PRIMARY AND SECONDARY AIR SUPPLY TUBES FROM THE FOOT VALVE TO THE PRIMARY AND SECONDARY AIR TANKS WERE REVERSED AT THE TANK WHICH FAILS TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS.

Mar 30, 2005 – CERTAIN 2004-2006 MY IC CORPORATION CE, FE, AND RE SCHOOL BUSES MANUFACTURED FROM MAY 12, 2003, THROUGH MARCH 2, 2005, EQUIPPED WITH CHILD RESTRAINT ANCHORAGE SYSTEMS. THE DIAMETER LATCH ATTACHMENT BARS EXCEED THE DIAMETER REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, CHILD RESTRAINT ANCHORAGE SYSTEMS, WHICH MAY MAKE IT DIFFICULT TO USE WITH FUTURE CAR SEAT ATTACHMENTS. IN ADDITION, SOME OF THE LATCH ATTACHMENTS ARE LOCATED TOO FAR FORWARD OF THE SEAT BACK.

Mar 30, 2005 – CERTAIN 2003, 2005, AND 2006 MY IC CORPORATION RE SCHOOL AND COMMERCIAL BUSES MANUFACTURED BETWEEN JANUARY 29, 2003, AND MARCH 9, 2005. THERE CAN BE METAL TO METAL INTERFERENCE AT THE DRIVELINE U-JOINT. THIS INTERFERENCE CAN LOOSEN THE AXLE STRAP OR CAUSE THE STRAP OR STRAP BOLTS TO BREAK BECAUSE OF FATIGUE STRESSES, CAUSING THE DRIVESHAFT TO SEPARATE FROM THE AXLE YOKE.

Mar 28, 2005 – CERTAIN 2003-2006 MY IC CE, FE, AND RE SCHOOL BUSES AND RE COMMERCIAL BUSES MANUFACTURED BETWEEN FEBRUARY 4, 2003, AND MARCH 1, 2005, AND EQUIPPED WITH WEBASTO COOLANT HEATERS. THE STAINLESS STEEL WALLS OF THE BURNER TUBES INCORPORATED INTO WEBASTO COOLANT HEATERS MAY BE MADE OF A MATERIAL THAT IS NOT WITHIN SPECIFICATION AND MAY FAIL PREMATURELY.

May 24, 2004 – ON CERTAIN SCHOOL BUSES, THE INSTRUCTIONS ON HOW TO OPERATE THE EMERGENCY EXIT DID NOT MEET THE MINIMAL LETTER HEIGHT OF 1-CENTERMETER. THESE BUSES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO 217, BUS EMERGENCY EXITS AND WINDOW RETENTION AND RELEASE.

Feb 24, 2004 – ON CERTAIN "SPECIAL NEEDS" SCHOOL BUSES EQUIPPED WITH SUR-LOC "L" WHEELCHAIR TRACKS, THE LIFT MOUNTING BOLTS COULD CORRODE IF MOISTURE OCCURS IN THE TREATED PLYWOOD FLOOR.