INFINITI G35 Recalls

Jun 24, 2011 – ZF SERVICE IS RECALL CERTAIN CLUTCH KIT ASSEMBLIES, PART NUMBER SX: K70358-01, SHIPPED TO WHOLESALERS AS SERVICE PARTS BETWEEN SEPTEMBER 1, 2010, AND MARCH 8, 2011. THESE SERVICE PARTS ARE INTENDED FOR USE ON MODEL YEAR 2003-2006 NISSAN 350Z AND INFINITI G35 VEHICLES. THE SX: K70358-01 CLUTCH KIT CONTAINS AN OVERSIZED CLUTCH DISC.

Apr 27, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2005 THROUGH 2007 INFINITI G35 SEDANS MANUFACTURED FROM MARCH 29, 2004 THROUGH AUGUST 25, 2006 AND INFINITI G35 COUPES MANUFACTURED FROM APRIL 1, 2004 THROUGH MAY 30, 2007. THE WIRE HARNESS CONNECTING THE BELT TENSION SENSOR (BTS) AND THE OCCUPANT DETECTION SENSOR (ODS) CONTROL UNIT UNDER THE FRONT PASSENGER SEAT CAN EXPERIENCE RELATIVE MOVEMENT WHICH CAN CAUSE WEAR AND OXIDIZATION OF THE TERMINALS AND MAY CAUSE INTERRUPTION OF THE SIGNAL.

Oct 07, 2008 – NISSAN IS RECALLING 204,361 MY 2007-2008 ALTIMA, ALTIMA HYBRID, 350Z, 350Z ROADSTER, MY 2008 ALTIMA COUPE, ROGUE, MY 2009 MURANO, AND INFINITI MY 2007-2008 G35 SEDAN, MY 2008 G37 COUPE AND EX35 PASSENGER VEHICLES EQUIPPED WITH CONTINENTAL AUTOMOTIVE SYSTEMS' OCCUPANT CLASSIFICATION SYSTEM (OCS) CONTROL UNITS. A VARISTOR IN THE OCS CONTROL UNIT LOCATED IN THE PASSENGER SEAT CUSHION MAY HAVE BEEN MANUFACTURED OUT OF SPECIFICATION. UNDER CERTAIN CONDITIONS, THIS COULD CAUSE AN INTERRUPTION OF SIGNAL BETWEEN THE OCS AND THE AIR BAG CONTROL UNIT (ACU).

Oct 13, 2006 – CERTAIN VEHICLES FAIL TO COMPLY WITH THE "VERTICAL GRADIENT" AND "HEADLAMP PHOTOMETRIC VALUES" REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, 'LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.'

Jun 29, 2006 – CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Dec 13, 2005 – ON CERTAIN PASSENGER AND SPORT UTILITY VEHICLES, THE FUEL FILLER HOSE MAY CRACK AND RESULT IN FUEL LEAKAGE FROM THE HOSE WHILE REFUELING.

Nov 17, 2003 – ON CERTAIN PASSENGER VEHICLES, THE CIRCUIT BOARD FOR THE CRANK POSITION SENSOR OR CAM POSITION SENSOR MAY HAVE AN IMPROPER SOLDER JOINT DUE TO SOLDER DEFORMATION CAUSED BY HEAT STRESS ACCELERATED BY THE EXISTENCE OF FLUX RESIDUE DURING THE SOLDERING PROCESS.

Jun 02, 2003 – ON CERTAIN SEDAN AND COUPE MODEL VEHICLES, THE BRAKE STOP LAMP SWITCH MAY MALFUNCTION.

Dec 12, 2002 – CERTAIN SEDANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." IN THE ASSEMBLY OF THE HEADLAMPS, IT IS NECESSARY TO HAVE A MEANS TO ADJUST THE HEADLAMPS. TAMPERPROOF CAPS TO PREVENT HORIZONTAL ADJUSTMENT OF THE HEADLAMPS ARE THEN INSTALLED. SOME OF THESE VEHICLES ARE MISSING THE TAMPERPROOF CAPS.

Sep 12, 2002 – ON CERTAIN PASSENGER VEHICLES, THE FUEL HOSE CONNECTION FOR THE OUTLET OF THE FUEL PUMP WHICH IS LOCATED AT THE TOP OF THE FUEL TANK MAY NOT HAVE BEEN PROPERLY ATTACHED WHEN THE VEHICLE WAS ASSEMBLED AND COULD COME LOOSE WHILE DRIVING OR WHEN STARTING THE ENGINE.