INTERNATIONAL HARVESTER Recalls

Apr 03, 2003 – ON CERTAIN HEAVY DUTY TRUCKS, A BRASS FITTING CONNECTS THE DOUBLE CHECK VALVE TO THE BRAKE RELAY VALVE. WITH CERTAIN INPUTS TO THE VEHICLE, THE WEIGHT OF THE CHECK VALVE ON THE FITTING CAN CAUSE THE ASSEMBLY TO RESONATE. THE SUBJECT VIBRATION CAN CAUSE EXCESSIVE STRAIN LEVELS IN THE FITTING, WHICH COULD EVENTUALLY FATIGUE AND FAIL.

Mar 06, 2003 – ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH BOSTROM DRIVER SEAT MODELS 910, 910SC, OR 914 AND INTERNATIONAL'S PARKING BRAKE CODE 04036, IF SOMEONE OUTSIDE THE CAB ADJUSTS/SLIDES THE DRIVER'S SEAT TO ITS MOST FORWARD POSITION, WITH THE PARKING BRAKE SET, THE SEAT WILL CONTACT AND RELEASE THE PARKING BRAKE LEVER.

Feb 25, 2003 – ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES.

Sep 20, 2002 – ON CERTAIN SCHOOL AND TRANSIT BUSES EQUIPPED WITH ELECTRONIC THROTTLE CONTROL/ACCELERATOR PEDALS SUPPLIED BY WILLIAMS CONTROLS INDUSTRIES, THE WELD ATTACHING THE CLEVIS TO THE PLATE HAS INSUFFICIENT PENETRATION AND COULD ALLOW THE CLEVIS TO SEPARATE FROM THE PLATE.

Jul 12, 2002 – ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH MANUAL TRANSMISSIONS, LOWER CLUTCH RODS WITH TURNBUCKLES ARE FAILING FROM FATIGUE NEAR THE TURNBUCKLE DUE TO BENDING FORCES EXPERIENCED DURING EACH CLUTCH PEDAL CYCLE.

May 20, 2002 – ON CERTAIN TRANSIT AND SCHOOL BUSES, A BRASS FITTING CONNECTS THE DOUBLE CHECK VALVE TO THE BRAKE RELAY VALVE. WITH CERTAIN INPUTS TO THE VEHICLE, THE WEIGHT OF THE CHECK VALVE ON THE FITTING CAN CAUSE THE ASSEMBLY TO RESONATE. THE SUBJECT VIBRATION CAN CAUSE EXCESSIVE STRAIN LEVELS IN THE FITTING, WHICH COULD EVENTUALLY FATIGUE AND FAIL.

May 20, 2002 – ON CERTAIN MEDIUM AND HEAVY DUTY TRUCKS, A BRASS FITTING CONNECTS THE DOUBLE CHECK VALVE TO THE BRAKE RELAY VALVE. WITH CERTAIN INPUTS TO THE VEHICLE, THE WEIGHT OF THE CHECK VALVE ON THE FITTING CAN CAUSE THE ASSEMBLY TO RESONATE. THE SUBJECT VIBRATION CAN CAUSE EXCESSIVE STRAIN LEVELS IN THE FITTING, WHICH COULD EVENTUALLY FATIGUE AND FAIL.

May 10, 2002 – CERTAIN HEAVY DUTY TRUCKS, TRUCK TRACTORS, AND BUSES EQUIPPED WITH 195/75R22.5 TIRES MOUNTED ON 7.5 INCH WIDE WHEELS FAIL TO COMPLY WITH REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS." THESE TIRES AND RIMS DO NOT MATCH.

Feb 15, 2002 – ON CERTAIN SCHOOL BUSES, GALVANIC CORROSION ON THE DIE CAST ADAPTER PLATE CAUSES DISTORTION OF THE WAGON WHEEL SEALS THAT ARE MOUNTED ON THE ADAPTER PLATE. IF THE SEALS BECOME DISTORTED, THE TIPPER VALVES CANNOT PROPERLY SEAT AGAINST THE WAGON WHEEL SEALS. IF THE TIPPER VALVES CANNOT SEAT COMPLETELY, THE FLUID CAN BACK FLOW PAST THE VALVES TOWARDS THE RESERVOIR AND CREATE A PRESSURE LOSS FOR THE FRONT BRAKES, THE REAR BRAKES, OR BOTH.

Oct 03, 2001 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS. THESE VEHICLES COULD EXPERIENCE A LOSS OF THE LOW BEAM HEADLIGHTS, THE HIGH BEAM HEADLIGHTS, OR BOTH. A SOFTWARE PROBLEM WITHIN THE ELECTRICAL SYSTEM CONTROLLER (ESC) CAN CAUSE THE CIRCUIT FOR THE LOW BEAM OR THE CIRCUIT FOR THE HIGH BEAM HEADLIGHTS TO FUSE OR OPEN, RESULTING IN LOSS OF EITHER THE LOW OR HIGH BEAM HEADLIGHTS OR POSSIBLY EVEN BOTH.