INTERNATIONAL 4300 Recalls

Jun 24, 2005 – ON CERTAIN 4X2 MEDIUM DUTY TRUCKS, A LONGER FRONT HYDRAULIC BRAKE HOSE WAS SUBSTITUTED FOR THE SHORTER, CORRECT LENGTH HOSE.

Oct 27, 2004 – ON CERTAIN TRUCKS BUILT WITH IROS REAR AIR SUSPENSION SYSTEMS, FOUR REAR SUSPENSION FASTENERS MAY NOT BE TIGHTENED SUFFICIENTLY. THIS HARDWARE CONNECTS THE MAIN SUPPORT MEMBERS OF THE REAR SUSPENSION TO THE HANGER BRACKETS.

Aug 25, 2004 – CERTAIN TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS," AND WITH PART 567, 'CERTIFICATION.' THE "COMPLETE VEHICLE" LABEL WITH THE GROSS VEHICLE WEIGHT RATING (GVWR), GROSS AXLE WEIGHT RATING (GAWR), RECOMMENDED TIRE SIZE AND TIRE PRESSURE WAS NOT INSTALLED ON THE VEHICLE.

Apr 22, 2004 – CERTAIN TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES." THE SEAT BELT LATCH FAILED A QUALITY REVIEW.

Aug 27, 2003 – CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS." THE PRIMARY AND SECONDARY AIR SUPPLY HOSES FROM THE FOOT VALVE TO THE PRIMARY AND SECONDARY AIR TANKS WERE IMPROPERLY ROUTED AT THE TANK.

Apr 29, 2003 – CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 104, "WINDSHIELD WIPING AND WASHING SYSTEMS." DUE TO THE DESIGN OF THE WINDSHIELD WASHER PUMP MOTOR CIRCUIT, THE SYSTEM'S ABILITY TO FUNCTION IS IMPAIRED WHEN IT IS FULL OF FROZEN WATER AND THE PUMP MOTOR SHAFT IS LOCKED OR FROZEN (CANNOT ROTATE).

Feb 25, 2003 – ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES.

Jan 28, 2003 – CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH HYDRAULIC BRAKES AND AN AIR POWERED PARKING BRAKE (BRAKE CODE 04GAS) FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, "HYDRAULIC AND ELECTRIC BRAKE SYSTEMS." THE HYDRAULIC BRAKE MONITOR MODULE WAS NOT INSTALLED ON CERTAIN VEHICLES.

Sep 20, 2002 – ON CERTAIN MEDIUM AND HEAVY DUTY TRUCKS BUILT WITH DRIVELINE PARKING BRAKE CODES 04GAR, THE PARKING BRAKE ASSEMBLY MAY NOT HOLD THE VEHICLE IN POSITION WHEN SET. FACTORS CONTRIBUTING TO THIS POSSIBILITY ARE AS FOLLOWS: (1) CRACKED OR BROKEN CAMS; (2) LOOSE OR BROKEN ANCHOR BOLTS; (3) INITIAL SHOE DIAMETER NOT SET PROPERLY DURING ASSEMBLY, WHICH CAN LEAD TO PROGRESSIVE COMPONENT DAMAGE; (4) BENT ADJUSTER LEVERS THAT CANNOT FUNCTION; OR (5) AUTOMATIC ADJUSTER CABLES THAT ARE DISCONNECTED.

Jul 12, 2002 – ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH MANUAL TRANSMISSIONS, LOWER CLUTCH RODS WITH TURNBUCKLES ARE FAILING FROM FATIGUE NEAR THE TURNBUCKLE DUE TO BENDING FORCES EXPERIENCED DURING EACH CLUTCH PEDAL CYCLE.