KENWORTH K100 Recalls

Dec 10, 2004 – ON CERTAIN TRUCKS, THE POWER FEED HARNESS P92-1993 TERMINALS WERE NOT PROPERLY CRIMPED.

Feb 13, 2003 – CERTAIN TRUCKS EQUIPPED WITH TRAILER CONNECTIONS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARDS (FMVSS) NO. 121, "AIR BRAKE SYSTEMS," AND NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THE SUPPLIER REMOVED A RUBBER GROMMET FROM THE TRAILER LIGHT LINE CONNECTOR. THE VEHICLES ARE EXPERIENCING CORROSION AT THE 7-WAY TRAILER CONNECTION. THIS CAUSES INTERMITTENT FLASHING/FLICKERING OF THE TRAILER LIGHTS.

Jul 15, 2002 – HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN ARVINMERITOR AND DANA AXLES. PETERBILT WILL RECALL 1,434 VEHICLES EQUIPPED WITH ARVINMERITOR AXLES MANUFACTURED FROM DECEMBER 11, 1999, TO MAY 14, 2000, AND FROM JULY 22 TO SEPTEMBER 30, 2000. KENWORTH WILL RECALL 859 VEHICLES EQUIPPED WITH ARVINMERITOR VEHICLES MANUFACTURED FROM DECEMBER 11, 1999, TO MAY 23, 2000, AND FROM JULY 27, 2000, TO SEPTEMBER 30, 2000 AND KENNWORTH WILL RECALL AN ADDITIONAL 4,151 VEHICLES EQUIPPED WITH DANA AXLES AND MANUFACTURED FROM JUNE 23 TO DECEMBER 6, 1999, AND FROM MAY 23 TO SEPTEMBER 30, 2000. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS.

Aug 28, 2001 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS.

May 17, 2001 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CHALMERS 1000 SERIES AND 800 SERIES SUSPENSION KITS. THESE SUSPENSION KITS MAY HAVE INSUFFICIENT PENETRATION OF THE WELD ATTACHING THE TORQUE ROD EYE TO THE TORQUE ROD TUBE.

Mar 01, 2001 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TIE ROD ASSEMBLIES MANUFACTURED BY TRW. THE SUSPECT TIE RODS CONTAIN 24-DL MODEL BALL SOCKETS. CERTAIN OF THE TIE ROD BALL-SOCKET BEARINGS HAVE A BELOW-SPECIFICATION CASE DEPTH AND/OR HARDNESS, WHICH CAN LEAD TO PREMATURE WEAR OF THE SOCKET.

Feb 20, 2001 – VEHICLE DESCRIPTION: VEHICLES EQUIPPED WITH 54" REAR AXLE SPACING CONFIGURATION OF THE AIRGLIDE 200 SUSPENSION WITH THE SERVICE APPLICATION IDENTIFIED AS LOGGER, DUMP TRUCK, OR TANKER. THE REAR SUSPENSION IS REGULARLY SUBJECTED TO EXTREME ARTICULATION, RESULTING IN FLEXING OF THE JOINT.

Sep 13, 2000 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH TRW TIE ROD ENDS ON CERTAIN MERITOR AXLES. THE TIE ROD AND DRAG LINK BALL STUD ENDS CONTAIN BEARINGS THAT ARE BELOW THE SPECIFIED CASE DEPTH AND/OR HARDNESS.

Jun 11, 1998 – VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CATERPILLAR 3406E ENGINES. THE ROUTING OF THE ELECTRICAL AND FUEL LINES CAN CAUSE CHAFFING OF THE WIRING HARNESS ON THE FUEL LINE.

Apr 03, 1996 – THE WIRES THAT CORRESPOND TO THE VEHICLE'S REAR TURN SIGNALS WERE REVERSED WHEN INSTALLED IN THE ELECTRICAL CONNECTOR.