KENWORTH Recalls

Nov 24, 2010 – PACCAR IS RECALLING CERTAIN MODEL YEAR KENWORTH T660 AND T800 VEHICLES MANUFACTURED FROM SEPTEMBER 13, 2010, THROUGH NOVEMBER 19, 2010, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. PART 567, "CERTIFICATION." THE STEER AXLE GAWR AND GVWR RECORDED ON THE VEHICLE'S DOOR LABELS MAY BE INACCURATE AND OVERSTATE THE ACTUAL LOAD CAPACITY OF COMPONENTS INSTALLED ON THE VEHICLE.

Oct 27, 2010 – PACCAR IS RECALLING CERTAIN MODEL YEAR KENWORTH T660, T700, T800 AND W900 VEHICLES MANUFACTURED FROM DECEMBER 22, 2008, THROUGH AUGUST 2, 2010, AND EQUIPPED WITH AG400L AIR DISC BRAKES. THE AIR DISC BRAKE CALIPER COULD BE INSTALLED ON THE WRONG SIDE OF THE DRIVE AXLE POTENTIALLY CAUSING INTERFERENCE WITH THE SUSPENSION BRACKET AND THE REAR SUSPENSION AS THE OUTERMOST BRAKE PADS WEAR AND THE FLOATING CALIPER MOVES INBOARD.

Oct 01, 2010 – PACCAR IS RECALLING CERTAIN MODEL YEAR KENWORTH AND PETERBILT VEHICLES. A MANUFACTURING DEFECT IN THE SEAL SUPPLIED BY A COMPONENT MANUFACTURER INSTALLED ON THE OUTPUT SHAFT OF THE EXHAUST GAS RECIRCULATION (EGR) VALVE ACTUATOR MAY CAUSE EVENTUAL DELAMINATION OF THE SEAL. DELAMINATION OF THE SEAL MAY ALLOW ENGINE OIL TO LEAK FROM THE EGR VALVE ONTO EXHAUST COMPONENTS.

Sep 29, 2010 – KENWORTH IS RECALLING CERTAIN MODEL YEAR 2011 T660, T800, W900, C500, T440, AND T470 VEHICLES MANUFACTURED FROM APRIL 1, 2009, THROUGH AUGUST 30, 2010. ONE OF THE FOUR HARNESS SPADE TERMINAL CONNECTIONS TO THE CHASSIS LOAD CENTER MAY BECOME COMPLETELY UNSEATED. A COMPLETELY UNSEATED CONNECTION MAY RESULT IN A POWER LOSS TO A PORTION OF THE VEHICLE'S EXTERIOR LIGHTING.

Jul 02, 2010 – PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES.

Jun 16, 2010 – KENWORTH IS RECALLING CERTAIN MODEL YEAR 2009 THROUGH 2010 T660 TRACTOR TRAILORS MANUFACTURED FROM JULY 1, 2008 THROUGH JULY 31, 2009. THE RETAINING PINS SECURING THE HOOD STRUT LOCK TUBE TO THE HOOD STRUT ASSEMBLY MAY BECOME LOOSE AND FALL OUT ALLOWING THE LOCK TUBE TO ROTATE ON THE STRUT ASSEMBLY. IN ITS NORMAL OPERATION THE SAFETY LATCH FEATURE IS AUTOMATICALLY SET AND IT PREVENTS THE HOOD FROM CLOSING. WITH THE HOOD CLOSED AND THE RETAINING PINS MISSING, THE LOCK TUBE MAY ROTATE RELATIVE TO THE GOOD STRUT RESULTING IN A NON-OPERATIONAL SAFETY LATCH FEATURE WHEN THE HOOD IS OPENED.

May 18, 2010 – KENWORTH IS RECALLING CERTAIN MODEL YEAR 2009 THROUGH 2011 C500 TRUCKS MANUFACTURED FROM OCTOBER 24, 2008 THROUGH JANUARY 13, 2010. DURING MANEUVERS WITH CERTAIN COMBINATIONS OF WHEEL TURN, ARTICULATION, AND BUMP, THE BRAKE CHAMBER CAN CONTACT THE REAR HOOD SUPPORT.

May 10, 2010 – KENWORTH IS RECALLING CERTAIN MODEL YEAR 2011 T270, T370, AND T800 TRUCKS MANUFACTURED FROM JANUARY 28 THROUGH MARCH 19, 2010, EQUIPPED WITH DV-2 AIR GOVERNOR CONTAINING PART NUMBER G90-1070-2111111 ON THE T270/370 MODEL TRUCKS AND PART NUMBER G90-1070-11113111 ON THE T800 MODEL TRUCKS. THE DV-2 AIR GOVERNOR WAS MISASSEMBLED WITH A BLANK PLUG INSTEAD OF A BREATHER. WITHOUT THE BREATHER INSTALLED, THE AIR GOVERNOR MAY NOT BE ABLE TO DETECT THE LOSS OF AIR PRESSURE IN THE AIR SYSTEM DURING NORMAL USE. THIS CONDITION MAY RESULT IN THE SLOW ACTIVATION OF THE EMERGENCY SPRING BRAKES.

May 04, 2010 – KENWORTH IS RECALLING CERTAIN MODEL YEAR 2010 T2000, T660, T800 AND W900 VEHICLES MANUFACTURED BETWEEN JULY 30, 2009 AND SEPTEMBER 18, 2009. THE REAR AXLE OUTER END HUB MAY HAVE NOT BEEN PRIMED WITH OIL PROPERLY DURING THE REAR AXLE INSTALLATION PROCESS. POTENTIAL LACK OF OIL MAY CAUSE THE OUTER END BEARING TO HEAT UP AND/OR SEIZE, POSSIBLY RESULTING IN THE OVERHEATING OF THE WHEEL END.

Apr 15, 2010 – KENWORTH IS RECALLING CERTAIN MODEL YEAR 2010 T270 AND T370 TRUCKS EQUIPPED WITH NON-LMS HUBS. THE SPINDLE NUT ATTACHING THE HUB AND BEARING TO THE AXLE SPINDLE (STEER OR DRIVE) MAY HAVE BEEN OVER-TORQUED DURING THE HUB INSTALLATION PROCESS.