MACK R Recalls

Aug 08, 1978 – THE POSSIBILITY EXISTS THAT THE ALUMINUM ENGINE REAR SUPPORT BRACKETS MAY FAIL DUE TO METAL FATIGUE. THIS TYPE OF FAILURE WOULD ALLOW THE ENGINE AND TRANSMISSION ASSEMBLY TO DISLOCATE DOWNWARD. THIS WILL RESULT IN THROTTLE CONTROL LOSS WITH THE ENGINE OPERATING CONTINUOUSLY IN THE MID TO UPPER RANGE OF THE GOVERNED SPEED RANGE.

Aug 08, 1978 – DEFICIENCIES, IN THE FORM OF FORGING LAPS, CRACKS AND EXCESSIVE DECARBURIZATION DURING HEAT TREATMENT, EXIST IN THE STEERING KNUCKLES. STRESSES IMPOSED WITH INTEGRAL HYDRAULIC POWER STEERING MAY LEAD TO A FAILURE IN THE AREA OF THE STEERING ARM ATTACHING BOSS. THIS TYPE OF FAILURE WOULD CAUSE LOSS OF STEERING CONTROL.

Aug 08, 1978 – THE EXISTING CROSS STEERING ARMS MAY HAVE INSUFFICIENT FATIGUE LIFE IN THE NECK AREA. THIS IS NEAR THE BOSS FOR THE CROSS STEERING TUBE BALL JOINT CONNECTION. FAILURE OF EITHER OF THE CROSS STEERING LEVERS COULD LEAD TO LOSS OF STEERING CONTROL OF THE RIGHT FRONT WHEEL.

Aug 07, 1978 – THE ALUMINUM FRONT SPRING BRACKET IS DEFECTIVE IN THAT IT MAY SHEAR AT THE POINT OF FRAME RAIL ATTACHMENT. THIS SHEARING COULD DISLOCATE THE STEERING AXLE.

Apr 04, 1978 – AN AXLE "NO BRAKE" CONDITION COULD RESULT FROM AN EATON CONTROLLER INTERNAL ELECTRICAL MALFUNCTION. THIS CONDITION MAY CAUSE THE ANTI-WHEEL LOCK VALVE SOLENOID TO BE CONTINUOUSLY ENERGIZED AND PREVENT THE BRAKES FROM BEING APPLIED ON ONE OF THE AXLES. AS A RESULT, THE ANTI-WHEEL LOCK WARNING LAMP IS NOT ACTIVATED.

Feb 09, 1978 – A DESIGN DEFICIENCY EXISTS IN THE AIR DRYER PIPING IN THE AREA OF THE PRESSURE RELIEF VALVE AND COMPRESSOR GOVERNOR CONTROL LINK. MOISTURE IS PASSED AND BUILDS UP IN THIS RELIEF VALVE AND CONTROL LINE. IN FREEZING AMBIENT TEMPERATURES, THIS MOISTURE MAY FREEZE, ALLOWING THE CHASSIS AIR SYSTEM PRESSURE TO EXCEED 150 PSI. EXCESSIVE AIR SYSTEM PRESSURE CAN CAUSE SEPARATION OF AIR PIPING CONNECTIONS AND AIR SYSTEM VALVE FAILURE.

Feb 09, 1978 – THE TEE BRACKET, WHICH IS MOUNTED ON THE FRONT AXLE OF THE BOGIE, MAY FAIL DUE TO VIBRATION BROUGHT ON BY ROAD SURFACE IRREGULARITIES. BRACKET FAILURE WOULD LEAVE THE TEE BRACKET UNSUPPORTED AND CAUSE BROKEN HOSE CONNECTOR FITTINGS. THIS WOULD RESULT IN AUTOMATIC APPLICATION OF THE SPRING EMERGENCY BRAKES.

Feb 09, 1978 – THE SYNFLEX-TYPE OIL PRESSURE SIGNAL LINE MAY HAVE BEEN ROUTED TOO CLOSE TO THE EXHAUST MANIFOLD. EXCESSIVE HEAT MAY CAUSE THE LINE TO RUPTURE, AND OIL LEAKAGE MAY OCCUR.

Nov 21, 1977 – A DEFICIENCY EXISTS IN THE WELDS SECURING THE REAR SPRING INSULATOR BRACKET TO THE AXLE HOUSING. THIS IS DUE TO IMPROPER POSITIONING OF THE WELD, IN RELATIONSHIP TO THE BRACKET AND AXLE HOUSING. FAILURE OF THE WELDS WOULD CAUSE SEPARATION OF THE SPRING INSULATOR BRACKET AND THE AXLE HOUSING, RESULTING IN IMPROPER ALIGNMENT OF THE AFFECTED AXLE.

Oct 12, 1977 – THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.