MACK Recalls

Feb 09, 1978 – THE TEE BRACKET, WHICH IS MOUNTED ON THE FRONT AXLE OF THE BOGIE, MAY FAIL DUE TO VIBRATION BROUGHT ON BY ROAD SURFACE IRREGULARITIES. BRACKET FAILURE WOULD LEAVE THE TEE BRACKET UNSUPPORTED AND CAUSE BROKEN HOSE CONNECTOR FITTINGS. THIS WOULD RESULT IN AUTOMATIC APPLICATION OF THE SPRING EMERGENCY BRAKES.

Feb 09, 1978 – THE SYNFLEX-TYPE OIL PRESSURE SIGNAL LINE MAY HAVE BEEN ROUTED TOO CLOSE TO THE EXHAUST MANIFOLD. EXCESSIVE HEAT MAY CAUSE THE LINE TO RUPTURE, AND OIL LEAKAGE MAY OCCUR.

Nov 21, 1977 – THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 207, "SEATING SYSTEMS", AND 210, "SEAT BELT ASSEMBLY ANCHORAGES". VEHICLES EQUIPPED WITH VIKING T-BAR SEATS HAVE THE SEAT BELT ANCHORAGE LOCATED UNDER THE SEAT. THE TETHER BELT RUPTURED WHEN SUBJECTED TO THE FORCES REQUIRED IN THE SAFETY TEST.

Nov 21, 1977 – A DEFICIENCY EXISTS IN THE WELDS SECURING THE REAR SPRING INSULATOR BRACKET TO THE AXLE HOUSING. THIS IS DUE TO IMPROPER POSITIONING OF THE WELD, IN RELATIONSHIP TO THE BRACKET AND AXLE HOUSING. FAILURE OF THE WELDS WOULD CAUSE SEPARATION OF THE SPRING INSULATOR BRACKET AND THE AXLE HOUSING, RESULTING IN IMPROPER ALIGNMENT OF THE AFFECTED AXLE.

Oct 12, 1977 – THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.

Oct 12, 1977 – THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEATBELT ASSEMBLIES". ALTHOUGH THE SEATBELTS IN QUESTION PERFORMED MARGINALLY WITH RESPECT TO THE 5000 LB. LOAD REQUIREMENT, ADDITIONAL TESTING CONFIRMED THAT THE ANCHOR COULD FAIL, ALLOWING EITHER THE ANCHOR TO SLIP OVER THE HOLD-DOWN NUT OR THE ANCHOR TO SEPARATE INTO TWO PIECES.

Sep 19, 1977 – THE FRONT WHEEL ALUMINUM HUBS ON THE INVOLVED VEHICLES MAY BE SUBJECT TO CRACKS WHICH MAY PROGRESS CIRCUMFERENTIALLY AROUND THE BARREL OF THE HUB. THIS COULD LEAD TO A FRACTURE IN THE "BARREL" POSITION OF THE HUB AND COMPLETE HUB FAILURE.

Jun 17, 1977 – THE FRONT WHEEL RIM CLAMP STUDS, INSTALLED ON THE INVOLVED VEHICLES, MAY NOT HAVE BEEN MANUFACTURED CORRECTLY, CAUSING A BRITTLE CONDITION IN THE THREAD ROOT AREA. THE STUDS COULD EVENTUALLY CRACK AND BREAK WHEN WHEEL NUTS ARE TIGHTENED TO SPECIFICATIONS.

Jan 01, 1977 – THE LOWER STEERING SHAFT YOKE CLAMP BOLTS ON THE INVOLVED VEHICLES MAY NOT HAVE BEEN SUFFICIENTLY TIGHTENED. SHOULD THESE BOLTS LOSSEN AND COME OFF, THE LOWER STEERING SHAFT COULD SEPARATE FROM THE STEERING GEAR.

Jan 01, 1977 – CRACKS MAY BE PRESENT IN THE BRAKE SPIDER. THESE CRACKS COULD EVENTUALLY CAUSE THE BRAKE SPIDER TO FAIL. THIS COULD ALLOW SEPARATION OF THAT PORTION OF THE BRAKE SPIDER THAT RETAINS THE BRAKE CAMSHAFT, THE BRAKE CHAMBER, AND THE BRAKE CHAMBER BRACKET FROM THE FOUNDATION BRAKE ASSEMBLY. BRAKE PULL IN THE DIRECTION OPPOSITE THE AFFECTED WHEEL LOCATION OR WHEEL LOCK-UP ON THE AFFECTED WHEEL COULD OCCUR.