PONTIAC SUNFIRE Recalls

Oct 17, 2008 – DORMAN PRODUCTS IS RECALLING 3,900 INTERMEDIATE STEERING SHAFTS DORMAN PART NOS. 425-151, 425-152, AND 425-153, (SOLD UNDER DORMAN'S "OE SOLUTIONS" BRAND NAME), BALKAMP #'S 7-3057, 7-3058, 7-3059 (SOLD UNDER THE "NAPA" BRAND NAME), AND PLATINUM PARTS #'S 2425151, 2425152, AND 2425153 MANUFACTURED DURING THE MONTH OF SEPTEMBER 2007. THESE REPLACEMENT STEERING SHAFTS CAN BE USED ON THE VEHICLES LISTED ABOVE. THE WELD CONNECTING THE INNER TUBE TO THE OUTER TUBE MAY BE DEFECTIVE.

Mar 12, 2007 – CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

Feb 26, 2007 – CERTAIN DELPHI AFTERMARKET FUEL PUMP MODULES / MODULE RESERVOIR ASSEMBLIES (MRA) THAT WERE SOLD FOR USE ON THE ABOVE LISTED VEHICLES. DURING PRODUCTION THE MRAS VENT AND FUEL RETURN TUBES WERE REVERSED. THIS CONDITION CAN RESULT IN THE VEHICLE NOT RUNNING CORRECTLY (IDLE ROUGH AND/OR STALL) DUE TO AN OVERLY RICH FUEL BLEND OR THE VEHICLE'S EVAPORATIVE EMISSION CARBON CANISTER MAY LEAK FUEL.

Mar 23, 2006 – CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

Nov 01, 2004 – ON CERTAIN PASSENGER VEHICLES, THE REAR LAMPS THAT PROVIDE STOP AND TURN SIGNALS AND TAIL LAMP FUNCTIONS STOP WORKING BECAUSE OF INADEQUATE CONTACT BETWEEN THE BULB AND SOCKET. IN ADDITION, IF ONE BULBS WERE TO BECOME INOPERATIVE WHILE THE VEHICLE WAS OPERATING IN CRUISE CONTROL, THE CRUISE CONTROL WOULD DISENGAGE WHEN THE REMAINING BULB WAS ACTIVATED. IF BOTH LAMPS WERE TO BECOME INOPERATIVE, THE CRUISE CONTROL WOULD NOT ENGAGE.

Jun 23, 2004 – CERTAIN PASSENGER VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, 'SEAT BELT ASSEMBLY ANCHORAGES.' THE PASSENGER-SIDE REAR SAFETY BELT MAY HAVE BEEN INSTALLED WITH AN INCORRECT NUT AND BOLT.

Jan 27, 2004 – ON CERTAIN PASSENGER VEHICLES. IF THE ENGINE FAILS TO START AND THE DRIVER HOLDS THE KEY IN THE "START" POSITION FOR AN EXTENDED PERIOD, HIGH CURRENT FLOWS THROUGH THE IGNITION SWITCH, AND SOMETIMES PRODUCES ENOUGH HEAT TO MELT INTERNAL SWITCH PARTS.

Nov 04, 2002 – CERTAIN PASSENGER VEHICLES AND MINI VANS HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE AND SOME OTHER RETAINERS USED IN VEHICLES ASSEMBLED BETWEEN JANUARY 1, 1996 AND OCTOBER 31, 1997, COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.

Mar 06, 2002 – ON CERTAIN PASSENGER VEHICLES. IF THE ENGINE FAILS TO START AND THE DRIVER HOLDS THE KEY IN THE "START" POSITION FOR AN EXTENDED PERIOD, HIGH CURRENT FLOWS THROUGH THE IGNITION SWITCH, AND SOMETIMES PRODUCES ENOUGH HEAT TO MELT INTERNAL SWITCH PARTS.

Aug 11, 1999 – VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES DO NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 101, "CONTROL LOCATION, IDENTIFICATION, AND ILLUMINATION." THE INSTRUMENT PANEL BACKLIGHTING MAY NOT FUNCTION AFTER ADJUSTING THE INTERIOR LIGHT INTENSITY.