AM GENERAL Recalls

Aug 31, 2011 – AM GENERAL IS RECALLING CERTAIN REPLACEMENT FRAMES MANUFACTURED FROM FEBRUARY 18, 2010, THROUGH JANUARY 31, 2011, SOLD FOR USE ON MODEL YEAR 1987-1994 UNITED STATES POSTAL SERVICE LONG LIFE VEHICLES. CRACKS MAY DEVELOP IN THE WELDS THAT ATTACH THE STEERING GEAR BRACKET TO THE FRAME. IF NOT ADDRESSED, THE STEERING GEAR BRACKET MAY SEPARATE FROM THE FRAME BUT REMAIN ATTACHED TO THE VEHICLE VIA THE STABILIZER BAR BRACKET.

Oct 24, 2007 – CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

May 19, 2006 – CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

Nov 13, 2002 – ON CERTAIN VEHICLES, THE FUEL LINES CAN CONTACT A ROUGH EDGE ON THE TRANSMISSION CASE, RESULTING IN CHAFFED LINES AND FUEL LEAKAGE.

Oct 31, 2001 – VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE TURN SIGNAL SWITCH PLASTIC CANCELLATION PIN CAN WEAR PREMATURELY CAUSING THE SIGNALS TO FAIL TO CANCEL AFTER COMPLETING A TURN.

Jan 11, 2000 – VEHICLE DESCRIPTION: A POTENTIAL CHAFING CONDITION OCCURS BETWEEN THE FLEXIBLE BRAKE LINES WHICH CONNECT THE MASTER CYLINDER TO THE ABS MODULATOR. THIS CONDITION CAN LEAD TO ONE OR BOTH OF THE BRAKE LINES DEVELOPING A BRAKE FLUID LEAK.

Mar 23, 1999 – VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES. THE NUTS USED TO ATTACH THE MASTER CYLINDER TO THE HYDROBOOST BOLTS WERE OF THE METRIC TYPE RATHER THAN THE REQUIRED ENGLISH TYPE.

Sep 27, 1996 – VEHICLE DESCRIPTION: BUSES EQUIPPED WITH ISRINGHAUSEN SEATS IN THE DRIVER POSITION. TWO WELDS LOCATED ON THE BACK REST ADJUSTMENT SIDE OF THE SEAT FRAME DID NOT MEET THE MANUFACTURER'S SPECIFICATIONS.

Mar 12, 1996 – THE COATING USED TO PROTECT THE ACCELERATOR PEDAL SHAFT IS INCOMPATIBLE WITH THE BRONZE BUSHING THROUGH WHICH THE SHAFT PASSES. OVER TIME, AND IN THE PRESENCE OF A CORROSIVE ENVIRONMENT (WATER, ROAD SALT), THE SHAFT CAN CORRODE INSIDE THE BUSHING INCREASING THE AMOUNT OF FRICTION BETWEEN THE ROTATING SHAFT AND THE STATIONARY BUSHING.

Aug 18, 1995 – UNDER HIGH AMBIENT TEMPERATURES (GREATER THAN 95 DEGREES FAHRENHEIT) AND THE FUEL TANK LEVEL BETWEEN 1/4 AND 1/2 FULL, THE FUEL TANK INTERNAL PRESSURE CAN INCREASE CAUSING THE TANK TO EXPAND. TANK EXPANSION CAUSES AN INTERFERENCE BETWEEN THE FUEL TANK PROTECTIVE SHIELD AND THE PROPELLER SHAFT RESULTING A HOLE IN THE FUEL TANK AT THE POINT OF SHIELD-TO-SHAFT CONTACT.