NISSAN Recalls

Sep 10, 2010 – NISSAN IS RECALLING CERTAIN VEHICLES THAT WERE EQUIPPED WITH A GARMIN NUVI MODEL 750 NAVIGATION SYSTEM. THE BATTERIES CONTAINED IN THE AFFECTED GPS UNITS CAN OVERHEAT.

Sep 03, 2010 – MARATHON IS RECALLING CERTAIN SEAT COVERS, BRAND SUPERHIDES WITH PART NUMBERS 593, 594, 578, 960, 228, 228-09, 267-08, 333, 625, AND 630, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE SEAT COVERS ARE MADE OF HEAVIER THREAD AND ARE NOT COMPATIBLE WITH SEATS CONTAINING SIDE AIRBAGS. THE HEAVIER SEAT COVER COULD INTERFERE WITH FULL DEPLOYMENT OF THE AIRBAG IN THE EVENT OF A CRASH.

Aug 12, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2010 NISSAN FRONTIER KING CAB VEHICLES MANUFACTURED FROM JUNE 10, 2010 THROUGH JUNE 26, 2010. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." THE WELD BETWEEN THE TETHER ANCHOR AND THE SEAT GUSSET BRACKET IS OUT-OF-SPECIFICATION. AS A RESULT, AND BASED ON NISSAN'S ENGINEERING JUDGMENT, THE TETHER ANCHOR COULD SEPARATE FROM THE SEAT WHEN TESTED UNDER THE CONDITIONS REQUIRED BY THE STANDARD.

Aug 09, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2010 NISSAN ARMADA VEHICLES MANUFACTURED FROM JUNE 7, 2010 THROUGH JUNE 11, 2010. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, "SEATING SYSTEMS." THE SECOND ROW CENTER SEAT HINGE ASSEMBLY WAS MANUFACTURED OUT OF SPECIFICATION. THIS MAY PREVENT THE REAR CENTER SEATBACK FROM FULLY LOCKING IN THE IN-USE (UPRIGHT) POSITION.

Jul 22, 2010 – NISSAN IS RECALLING MODEL YEAR 2009-2010 NISSAN CUBE VEHICLES MANUFACTURED FROM JANUARY 30, 2009 THROUGH JULY 30, 2010. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, "FUEL SYSTEM INTEGRITY." WHEN THE VEHICLE WAS ROTATED FOLLOWING A REAR MOVING BARRIER CRASH TEST AS REQUIRED, THE AMOUNT OF FUEL LEAKAGE EXCEEDED THE ALLOWABLE LIMITS.

Jul 22, 2010 – NISSAN IS RECALLING MODEL YEAR 2008 NISSAN ARMADA AND INFINITI QX56 VEHICLES MANUFACTURED FROM FEBRUARY 7, 2007 THROUGH FEBRUARY 14, 2007. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 201, "PROTECTION IN INTERIOR IMPACT." AN OUT-OF-SPECIFICATION A-PILLAR FINISHER MIGHT IMPEDE THE CORRECT INFLATION OF THE SIDE CURTAIN AIR BAG NEAR THE UPPER PORTION OF THE B-PILLAR.

Jul 06, 2010 – NISSAN IS RECALLING FORTY-SIX CERTAIN MODEL YEAR 2002 PATHFINDER AND INFINITI QX4 VEHICLES MANUFACTURED FROM AUGUST 24, 2001 THROUGH AUGUST 28, 2001. THE AIR BAG INFLATOR CONTAINS PROPELLANT WAFERS THAT ARE REQUIRED TO PROPERLY DEPLOY THE FRONT PASSENGER AIR BAG. DUE TO IMPROPER PROPELLANT WAFER INSTALLATION DURING THE AIR BAG INFLATOR ASSEMBLY PROCESS, SOME AIR BAG INFLATORS MAY BE MISSING ONE OF THE WAFERS. AS A RESULT, THE REMAINING WAFERS IN THE INFLATOR USED FOR THE DEPLOYMENT OF THE FRONT PASSENGER AIR BAG MAY, OVER TIME, BREAK UP INTO POWDER DUE TO NORMAL VIBRATION EXPERIENCED WHILE DRIVING. THIS CAUSES THE COMBUSTION RATE OF THE PROPELLANT TO INCREASE INSIDE THE INFLATOR, WHICH CAN LEAD TO INTERNAL PRESSURE RISING SUDDENLY DURING AIR BAG DEPLOYMENT.

May 20, 2010 – NISSAN IS RECALLING CERTAIN FRONT AND REAR LOWER LINKS, P/NOS. 54501ZQ00A, 54500ZQ00A, 551A1ZQ00A, 551A0ZQ00A , 54501EA00A, 54500EA00A, 551A1EA500, 551A0EA500, 54501ZR00A, AND 54500ZR00A, SOLD BETWEEN NOVEMBER 25, 2009 AND MAY 14, 2010 AS REPLACEMENT PARTS FOR MODEL YEAR 2004 THROUGH 2010 TITAN, ARMADA, AND QX56, AND MODEL YEARS 2005 THROUGH 2010 FRONTIER, XTERRA, AND PATHFINDER VEHICLES. THE LOWER CONTROL LINK ASSEMBLY HAS TWO CYLINDRICAL COLLARS FORMING THE INBOARD ATTACHMENT POINTS TO THE CHASSIS. DUE TO AN IMPROPER WELDING PROCESS SOME COLLARS MAY CONTAIN WELDS THAT DO NOT MEET STRENGTH SPECIFICATIONS.

May 14, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2010 TITAN, ARMADA, QX56, FRONTIER, XTERRA, AND PATHFINDER VEHICLES MANUFACTURED FROM NOVEMBER 19, 2009 THROUGH MARCH 3, 2010. THE LOWER CONTROL LINK ASSEMBLY HAS TWO CYLINDRICAL COLLARS FORMING THE INBOARD ATTACHMENT POINTS TO THE CHASSIS. DUE TO AN IMPROPER WELDING PROCESS SOME COLLARS MAY CONTAIN WELDS THAT DO NOT MEET STRENGTH SPECIFICATIONS.

May 07, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2010 ALTIMA VEHICLES MANUFACTURED FROM APRIL 7, 2010 THROUGH APRIL 13, 2010. SOME OF THE FRONT SIDE MEMBER ASSEMBLY COMPONENTS MAY NOT HAVE BEEN WELDED TO SPECIFICATION DUE TO A TOOL MAINTENANCE ERROR.