NISSAN Recalls

Dec 08, 2011 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 NISSAN JUKE VEHICLES MANUFACTURED FROM APRIL 9, 2010, THROUGH MAY 12, 2011. THE TURBOCHARGER BOOST SENSOR BRACKET MAY SEPARATE FROM THE AIR INLET TUBE DUE TO A DEFECTIVE WELD.

Nov 23, 2011 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 ROGUE VEHICLES MANUFACTURED FROM AUGUST 17, 2010, THROUGH OCTOBER 30, 2010. THE CIRCUIT BOARD MAY NOT HAVE BEEN INSTALLED IN THE CORRECT POSITION ON CERTAIN ELECTRIC POWER STEERING (EPS) ASSIST CONTROL UNITS. THIS MAY CAUSE ADDITIONAL STRESS ON THE SOLDER OF THE TERMINAL TO THE CIRCUIT BOARD RESULTING IN THE SOLDER CRACKING AND SEPARATING COMPLETELY FROM THE CIRCUIT BOARD.

Nov 04, 2011 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 INFINITI G37 COUPE VEHICLES AND CERTAIN MODEL YEAR 2011 NISSAN 370Z VEHICLES MANUFACTURED FROM JULY 2, 2011, THROUGH AUGUST 29, 2011. DUE TO A PROGRAMMING ERROR, THE POWER WINDOW SWITCH CONTROLLER IN THE SUBJECT VEHICLES WAS MANUFACTURED OUT OF SPECIFICATION.

Aug 09, 2011 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2012 NISSAN ALTIMA VEHICLES MANUFACTURED FROM JUNE 15, 2011, THROUGH JUNE 21, 2011 AND MODEL YEAR 2012 NISSAN NV VEHICLES MANUFACTURED FROM JUNE 23, 2011, THROUGH JUNE 28, 2011 BECAUSE THE AIR BAG CONTROL UNIT (ACU) WAS ASSEMBLED INCORRECTLY.

Jul 19, 2011 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2011-2012 NISSAN ALTIMA SEDAN VEHICLES MANUFACTURED FROM APRIL 25, 2011, THROUGH JUNE 10, 2011 AT THE CANTON, MISSISSIPPI PLANT. THE TRANSVERSE LINK BOLT MAY NOT HAVE BEEN TORQUED TO THE PROPER SPECIFICATION. THIS CONDITION COULD CAUSE THE BOLT TO BECOME LOOSE WHILE THE VEHICLE IS BEING DRIVEN, CREATING A RATTLING NOISE AND VIBRATION.

Jun 24, 2011 – ZF SERVICE IS RECALL CERTAIN CLUTCH KIT ASSEMBLIES, PART NUMBER SX: K70358-01, SHIPPED TO WHOLESALERS AS SERVICE PARTS BETWEEN SEPTEMBER 1, 2010, AND MARCH 8, 2011. THESE SERVICE PARTS ARE INTENDED FOR USE ON MODEL YEAR 2003-2006 NISSAN 350Z AND INFINITI G35 VEHICLES. THE SX: K70358-01 CLUTCH KIT CONTAINS AN OVERSIZED CLUTCH DISC.

Apr 20, 2011 – NISSAN IS RECALLING CERTAIN MODEL YEAR 1996-2004 PATHFINDER AND MODEL YEAR 1997-2003 INFINITI QX4 VEHICLES ORIGINALLY SOLD, OR CURRENTLY REGISTERED IN, CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WASHINGTON D.C., WEST VIRGINIA AND WISCONSIN. IN AREAS OF THE COUNTRY IN WHICH HEAVY CONCENTRATIONS OF ROAD SALT ARE USED, A MIXTURE OF SNOW/WATER AND SALT MAY ENTER AN ASSEMBLY LOCATION HOLE IN THE UPPER STRUT HOUSING, CAUSING WATER TO COLLECT AT THE MATING SURFACE OF THE STRUT HOUSING PANEL AND THE INNER HOOD LEDGE ASSEMBLY. OVER TIME, THIS SNOW/WATER AND SALT INTRUSION MAY RESULT IN CORROSION OF THE STRUT TOWER HOUSING IN SOME SUBJECT VEHICLES.

Nov 12, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2010-2011 SENTRA VEHICLES, MANUFACTURED FROM MAY 22, 2010, THROUGH JULY 8, 2010. DUE TO A MACHINING IRREGULARITY, THE BOLT/WASHER SURFACE ON THE POSITIVE BATTERY TERMINAL CABLE END MAY ALLOW FOR A GAP TO OCCUR IN THE CONTACT AREA OF THE TERMINAL. THIS CAN RESULT IN A VOLTAGE DROP THAT MAY CAUSE DIFFICULTY STARTING THE VEHICLE AND COULD CAUSE DAMAGE TO THE ENGINE CONTROL MODULE.

Nov 11, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2002-2004 FRONTIER VEHICLES MANUFACTURED FROM JULY 9, 2001 THROUGH OCTOBER 20, 2004, AND MODEL YEAR 2002-2004, XTERRA VEHICLES MANUFACTURED FROM JULY 9, 2001, THROUGH JANUARY 6, 2005. OVER TIME CORROSION MAY FORM IN THE LOWER STEERING COLUMN JOINT AND LIMIT MOVEMENT OF THE JOINT. THE LIMITED MOVEMENT OF THIS JOINT MAY CREATE EXCESSIVE LOAD ON THE LOWER STEERING COLUMN SHAFT. IF THE VEHICLE CONTINUES TO BE DRIVEN IN THIS CONDITION, IT MAY LEAD TO CRACKING OF THE SHAFT DURING LOW SPEED MANEUVERS THAT REQUIRE LARGE STEERING INPUTS.

Oct 28, 2010 – NISSAN IS RECALLING CERTAIN MODEL YEAR 2004-2006 ARMADA, TITAN, INFINITI QX56 AND MODEL YEAR 2005-2006 FRONTIER, PATHFINDER AND XTERRA VEHICLES. THE INTELLIGENT POWER DISTRIBUTION MODULE (IPDM) ASSEMBLY CONTAINS AN ENGINE CONTROL MODULE (ECM) RELAY THAT HAS A DIODE FOR ELECTRICAL CURRENT NOISE REDUCTION. THE ECM RELAY MAY ALLOW SILICON VAPOR TO FORM AND, OVER TIME, THE SILICON EVAPORATES FROM THE DIODE MOLDING WHICH CAUSES SILICON OXIDE TO DEVELOP ON THE ECM RELAY CONTACT DUE TO ARCING.