INTERNATIONAL HARVESTER 3800 Recalls

Jun 03, 2004 – ON CERTAIN SCHOOL BUSES AND TRUCK MODEL VEHICLES MANUFACTURED BETWEEN FEBRUARY 28, 1999, THROUGH APRIL 5, 2004, THE ANTI-LOCK BRAKE SYSTEM ELECTRONIC CONTROL UNIT (ECU) MAY MISINTERPRET A CORRUPT WHEEL SPEED SIGNAL.

Feb 25, 2003 – ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES.

May 23, 2000 – VEHICLE DESCRIPTION: SCHOOL/TRANSIT BUSES AND MEDIUM DUTY TRUCKS. THE CASTINGS USED ON THE POWER STEERING PUMPS WERE NOT BUILT TO MATCH THE ENGINEERING DRAWINGS, RESULTING IN A THIN WALL IN THE PUMP CASTING OR A COMPLETE CONNECTION OF TWO PASSAGES THAT ARE SUPPOSED TO BE SEPARATED TO CONTROL FLUID FLOW. THE FLUID FLOW MAY BE REDUCED TO LESS THAN THE MINIMUM REQUIRED FLOW RATE TO PROVIDE FULL POWER ASSIST TO THE BRAKE SYSTEM WITH LOW ENGINE SPEED.

Nov 27, 1996 – VEHICLE DESCRIPTION: SCHOOL BUSES EQUIPPED WITH THE INTERNATIONAL I6 ELECTRONIC ENGINE AND AN EXTRA THICK BUS BODY FLOOR. THE ACCELERATOR PEDAL TO FLOOR CLEARANCE IS APPROXIMATELY 1.2 INCHES WITH A STANDARD BUS BODY FLOOR. HOWEVER, SOME CUSTOMERS ORDERED AN ADDITIONAL 3/4 INCH THICK FLOOR AND EXTRA THICK FLOOR MATS TO SERVE AS INSULATION IN COLD CLIMATES. WHEN THIS EXTRA FLOORING IS USED, THE BOTTOM EDGE OF THE ACCELERATOR PEDAL, WHEN DEPRESSED, CAN COME IN CONTACT WITH THE FLOOR.

Nov 27, 1996 – VEHICLE DESCRIPTION: SCHOOL BUSES AND HEAVY DUTY TRUCKS EQUIPPED WITH REAR AXLE ASSEMBLIES PRODUCED BY DANA SPICER. CERTAIN REAR AXLE ASSEMBLIES WERE IMPROPERLY HEAT TREATED WHICH COULD ALLOW PINION BREAKAGE AT THE PINION THREADS.

Nov 12, 1996 – THESE BUSES HAVE A TURN SIGNAL LEVER THAT WILL NOT OPERATE CONSISTENTLY IN THE LANE CHANGE MODE IF THE LEVER IS NOT MOVED TO THE POSITION WHERE RESISTANCE TO MOVEMENT IS FELT.

Sep 13, 1996 – THE WIRING FROM THE ELECTRONIC CONTROL UNIT WAS CONNECTED TO THE WRONG WHEEL SENSOR OR TO THE WRONG BRAKE MODULATOR VALVE. IT IS POSSIBLE THAT EITHER OR BOTH WIRING MAY HAVE OCCURRED AT EITHER THE FRONT OR REAR AXLE OR BOTH AXLES.

Jun 11, 1996 – THE AXLE HOUSINGS WERE MANUFACTURED WITH A TIGHT FRICTION WELD CURL RADIUS ON THE INSIDE DIAMETER OF THE AXLE HOUSING. UNDER OPERATIONAL LOADS, CRACKS CAN INITIATE AT THE WELD CURL RADIUS ON THE INSIDE OF THE HOUSING. THESE CRACKS MAY PROPAGATE, EVENTUALLY ALLOWING THE AXLE SPINDLE TO SEPARATE FROM THE AXLE HOUSING.

Mar 01, 1996 – THE FRONT WHEEL HUB CAN DEVELOP CRACKS AT THE WHEEL MOUNTING STUDS. WHEN MOUNTED TO THE HUB, THE HYDRAULIC BRAKE DISC ROTOR DOES NOT PROPERLY SUPPORT THE HUB AT THE WHEEL STUDS CAUSING EXCESSIVE STRESS AND FATIGUE CRACKS IN THE HUB.

Jun 27, 1995 – THE WIRE END OF THE HAND THROTTLE CABLE PASSES THROUGH A SPLIT PLASTIC GROMMET IN THE ACCELERATOR ROD. THIS WIRE CAN WORK THROUGH THE SLOT IN THE GROMMET AND BECOME LODGED BETWEEN THE GROMMET AND THE EDGE OF THE HOLE IN THE ACCELERATOR ROD.