INTERNATIONAL Recalls

Feb 25, 2003 – ON CERTAIN SCHOOL AND TRANSIT BUSES BUILT WITH BOSCH ZERO OFFSET PIN SLIDE (ZOPS) HYDRAULIC DISC BRAKES, THE ZOPS HYDRAULIC DISC BRAKES MAY EXPERIENCE CALIPERS STICKING IN THE APPLIED POSITION, WHICH CAN RESULT IN EXCESSIVE OR ABNORMAL HEAT GENERATION AT ONE OR MORE OF THE BRAKES.

Jan 28, 2003 – CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH HYDRAULIC BRAKES AND AN AIR POWERED PARKING BRAKE (BRAKE CODE 04GAS) FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, "HYDRAULIC AND ELECTRIC BRAKE SYSTEMS." THE HYDRAULIC BRAKE MONITOR MODULE WAS NOT INSTALLED ON CERTAIN VEHICLES.

Nov 15, 2002 – ON CERTAIN HEAVY DUTY TRUCKS, THE BOLTS AND LOCKING NUTS USED TO HOLD THE BRAKE SPIDERS OR BRAKE ANCHOR PLATES TIGHT TO THE AXLES WERE UNDER-TORQUED ON THE RIGHT SIDE OF THE VEHICLES. IF THE CLAMP LOAD ON THE BOLTS IS NOT SUFFICIENT, THE ANCHOR PLATE MAY MOVE WHEN THE BRAKE IS APPLIED IN EITHER THE FORWARD OR REVERSE DIRECTION.

Sep 25, 2002 – ON CERTAIN HEAVY DUTY TRUCKS, THE JOINT BETWEEN THE LOWER PORTION OF THE STEERING COLUMN AND THE UPPER END OF THE INTERMEDIATE STEERING SHAFT MAY HAVE A MISSING OR LOOSE PINCH BOLT. THIS CONDITION COULD ALSO OCCUR AT THE LOWER END OF THE INTERMEDIATE STEERING SHAFT AT THE STEERING GEAR CONNECTION.

Sep 20, 2002 – ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH BENDIX TC-7 TRAILER CONTROL HAND-OPERATED VALVE WITH PUSH-TO-CONNECT FITTINGS. THE DELIVERY PORT IN THE VALVE BODY MAY BE PARTIALLY BLOCKED DUE TO A PROBLEM DURING THE MODING PROCESS.

Sep 20, 2002 – ON CERTAIN MEDIUM AND HEAVY DUTY TRUCKS BUILT WITH DRIVELINE PARKING BRAKE CODES 04GAR, THE PARKING BRAKE ASSEMBLY MAY NOT HOLD THE VEHICLE IN POSITION WHEN SET. FACTORS CONTRIBUTING TO THIS POSSIBILITY ARE AS FOLLOWS: (1) CRACKED OR BROKEN CAMS; (2) LOOSE OR BROKEN ANCHOR BOLTS; (3) INITIAL SHOE DIAMETER NOT SET PROPERLY DURING ASSEMBLY, WHICH CAN LEAD TO PROGRESSIVE COMPONENT DAMAGE; (4) BENT ADJUSTER LEVERS THAT CANNOT FUNCTION; OR (5) AUTOMATIC ADJUSTER CABLES THAT ARE DISCONNECTED.

Sep 20, 2002 – ON CERTAIN SCHOOL AND TRANSIT BUSES EQUIPPED WITH ELECTRONIC THROTTLE CONTROL/ACCELERATOR PEDALS SUPPLIED BY WILLIAMS CONTROLS INDUSTRIES, THE WELD ATTACHING THE CLEVIS TO THE PLATE HAS INSUFFICIENT PENETRATION AND COULD ALLOW THE CLEVIS TO SEPARATE FROM THE PLATE.

Jul 26, 2002 – ON CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL VT365 ENGINES AND MANUFACTURED AT INTERNATIONAL DIESEL OF ALABAMA. THE INJECTOR DRIVER MODULES (IDM) BUILT FOR THE VT365 ENGINES COULD HAVE MISSING VIBRATION DAMPING/RETENTION SHELLS AND A MISSING HOT-MELT PROCESS ON THE DC/DC BOARDS.

Jul 26, 2002 – ON CERTAIN HEAVY DUTY TRUCKS, THE FUEL LINE IS ROUTED TOO CLOSE TO A TURBO CHARGER OUTLET/EXHAUST PIPE. IF AN INTERFERENCE CONDITION OCCURS BETWEEN THE FUEL HARNESS AND THE EXHAUST PIPE, THE FUEL LINE INSIDE THE REFLECTIVE HEAT WRAP COULD MELT DUE TO EXCESSIVE HEAT.

Jul 12, 2002 – ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH MANUAL TRANSMISSIONS, LOWER CLUTCH RODS WITH TURNBUCKLES ARE FAILING FROM FATIGUE NEAR THE TURNBUCKLE DUE TO BENDING FORCES EXPERIENCED DURING EACH CLUTCH PEDAL CYCLE.