STRICK Recalls

Oct 10, 2014 – Strick Trailers, LLC (Strick) is recalling certain model year 2009-2015 Dry Freight Van Trailers manufactured April 25, 2008, to June 5, 2014. The affected trailers are equipped with rear impact guards using gusset part numbers 40033/40034, 43191/43192, 63133/63134 or 67046/67047. The rear impact guards with these gussets do not meet federal standards for strength and energy absorption. As such, these trailers do not comply with the Federal Motor Vehicle Safety Standard No. 223, "Rear Impact Guards."

Jul 09, 2014 – Strick Trailers, LLC (Strick) is recalling certain model year 2011-2015 single axle van trailers manufactured March 2010 to March 2014. The affected trailers may be equipped with rear impact guard gussets part numbers 59653 and 59654. These rear impact guard gussets increase the chances of injury in the event of an accident. Thus, these trailers fail to comply with the Federal Motor Vehicles Safety Standards No. 223, "Rear Impact Guards."

Aug 29, 2012 – Strick Trailers (Strick) is recalling certain model year 2006-2012 dry freight single-axle trailers with air-ride suspensions mounted on a "C" channel sub-frame because the suspension assembly that is mounted on the "C" channel sub-frame may prematurely wear and fail.

Jan 25, 2011 – STRICK IS RECALL CERTAIN MODEL YEAR 2006-2009 DRY FREIGHT VANS EQUIPPED WITH ARVINMERITOR AXLES. THESE VEHICLES HAVE A DEFECT INVOLVING SPINDLE NUTS AND STAKE WASHERS WHICH HAS BEEN IDENTIFIED AS LOW TORQUE ON THE SPINDLE NUT ON ARVINMERITOR TL SERIES TRAILER AXLES INSTALLED IN VAN TRAILERS WHERE THE STAKE WASHER FOR THE NUT IS STAKED IN A SINGLE LOCATION AS OPPOSED TO MULTIPLE LOCATIONS.

Jun 17, 2004 – ON CERTAIN CONVERTER DOLLIES, THERE IS A CLEARANCE PROBLEM BETWEEN THE LOOP ON THE TRAILER AND THE LOOP ON THE DOLLY. THE HOOK ON THE END OF THE CHAIN WILL NOT PASS BETWEEN THE LOOP AND THE PINTLE HOOK.

Jun 17, 2004 – ON CERTAIN CONVERTER DOLLIES, THE CHECK VALVE BETWEEN THE AIR RESERVOIR AND THE BOOSTER VALVE WAS INSTALLED IN THE REVERSE POSITION WITH THE ARROW ON THE VALVE POINTING TOWARDS THE AIR RESERVOIR.

Jun 02, 2004 – ON CERTAIN CHASSIS EQUIPPED WITH THE SEALCO 508 RUBBER BAND CHECK VALVE THAT IS USED ON THE 110502 BRASS CONTROL PORT CAP ASSEMBLY WHICH IS INSTALLED IN THE CONTROL PORT OF SEALCO'S 11050, 110700 AND 110800 SPRING BRAKE CONTROL VALVES MAY DEVELOP A HOLE.

Nov 04, 2003 – ON CERTAIN TRAILERS EQUIPPED WITH BENDIX EC-30T ELECTRONIC CONTROL UNITS (ECU). IF THE TRAILER-MOUNTED ABS WARNING LAMP CIRCUIT EXPERIENCES AN ELECTRICAL SHORT AND THE SHORT IS NOT REPAIRED, THE HIGH SIDE POWER SWITCH INSIDE THE ECU THAT CONTROLS THE ILLUMINATION OF THE TRAILER-MOUNTED ABS WARNING LAMP MAY EVENTUALLY BECOME THERMALLY STRESSED AND EXPERIENCE AN ELECTRICAL SHORT.

May 15, 2003 – ON CERTAIN CONVERTER DOLLIES EQUIPPED WITH JOST INTERNATIONAL JSK 37U SERIES FIFTH WHEELS, A FATIGUE CRACK CAN DEVELOP IN THE BRACKET PIN WELD UNDER CERTAIN LOADING CONDITIONS.

Aug 15, 2002 – ON CERTAIN TRAILERS EQUIPPED WITH BENDIX SR-2, SR-4, AND SR-5 TRAILER SPRING BRAKE VALVE ASSEMBLIES, THE MOLDED RUBBER FACE OF THE INLET/EXHAUST VALVE (I/E VALVE) COMPONENT OF THE AFFECTED VALVES CAN SEPARATE FROM THE VALVE'S METAL INSERT. AIR CAN BE TRAPPED BY A SEPARATED I/E VALVE CAUSING IT TO BALLOON AND BLOCK THE EXHAUST PASSAGE OF THE TRAILER SPRING BRAKE CIRCUIT.