2013 FORD EXPLORER Complaints

My vehicles exterior A-pillar trim is coming off and pieces flew off on highway. I was told to contact Ford.

While driving a 2013 Ford Explorer, the vehicle experienced an electrical issue that caused the power steering system to malfunction. The power steering assist suddenly failed, making the steering wheel extremely difficult to turn. The failure occurred suddenly and at the time of the incident the vehicle was traveling 2 miles and I parked it immediately.This created a serious safety hazard, especially when attempting to turn or maneuver the vehicle. A warning message stating “Power Steering Assist Fault” did appear on the dashboard .Prior to the failure, there were no warning signs. Due to the sudden loss of power steering assist, the driver’s ability to safely control the vehicle was significantly reduced, increasing the risk of a crash. The issue has not yet been inspected. The vehicle is available for inspection upon request.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (STRUCTURE); however, the part to do the recall repair was not yet available. The contact stated that while driving at an undisclosed speed, the driver's and the passenger's side A-pillar trims were loose. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown.

The contact owns a 2013 Ford Explorer. The contact stated that while driving at an undisclosed speed, the steering wheel seized, with the power steering warning light illuminated. The contact stated that the steering wheel became difficult to turn. The vehicle was taken to an independent mechanic, but the vehicle was not diagnosed or repaired. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 201,226.

My backup camera is in reverse. When I use it everything is on the incorrect side which is a safety issue when backing up.

The contact owns a 2013 Ford Explorer. The contact stated that while driving at an undisclosed speed, the driver's side exterior A-pillar trim detached and struck another vehicle. No warning lights were illuminated. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was taken back to the residence. Several dealers were contacted and confirmed that the part was not yet available. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 146,000.

This is a complaint regarding the handling of safety recall 20S62 (also referenced as 20S32) by Ford Motors and the dealership that performed the recall repairs, Hallada Motors. The vehicle was taken by the previous owner to Hallada 3 separate times to address the same recall related to the rear suspension toe link/ball joint issue. Documentation indicates the most recent repair occurring in 2022. This recall specifically involves components connected to the rear suspension that, if not properly addressed, can lead to corrosion and structural damage affecting the frame. Based on the history of repeated recall repairs and the current condition of the vehicle, we believe that the repair approach taken was insufficient. By the time of the third recall service in 2022, the frame should have been thoroughly inspected and potentially replaced due to corrosion risk identified in the recall guidance. The vehicle is currently being inspected and serviced at Ewald Ford. Their technicians documented significant corrosion and unusual frame damage, which they photographed and submitted to Ford corporate while requesting that the recall case be reopened. Despite this documentation, Ford has refused to reopen the recall or authorize a frame replacement. Ewald Ford technicians noticed irregularities in the documentation from Hallada Motors. 2 separate entries list the mileage as exactly 87,600 miles and exactly 95,000 miles, both ending in multiple zeros. The technicians indicated this is unusual and raised concerns whether the recall work was properly completed. The vehicle now has severe frame corrosion and structural damage and is unsafe and unusable. We are without a vehicle and have incurred financial loss. We believe the current condition is the result of improper/incomplete recall repairs. We request a look at the recall repairs performed were completed in compliance & ford's refusal to reopen is consistent with safety obligations. Ford should be held accountable.

The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that while driving 60 MPH, the passenger's side A-pillar trim detached from the vehicle. The local dealer was contacted and confirmed that the part for the recall repair was not available. The dealer used black tape as an interim repair. The contact became aware that the seal around the front passenger’s side windshield had started to deteriorate. Recently, the contact noticed small amounts of water occasionally leaking inside the vehicle from the front passenger’s side windshield. The vehicle was not repaired after the most recent failure. The contact stated that the driver’s side A-pillar trim was loose. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue, and no assistance was offered. The manufacturer informed the contact that the seal and leak were symptoms of the recall, but not related to the recall, and therefore not covered under the recall. The failure mileage was unknown.

The contact owns a 2013 Ford Explorer. The contact stated that the trim along the front windshield had become loose, and the lining was pushed outward and was partially missing and detached. The contact was concerned that the windshield could potentially loosen or fall out due to the failure. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure). The local dealer was contacted and confirmed that parts were on back order. The vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was unknown.

I am submitting a formal safety complaint regarding a severe design defect in the 3.5L V6 engine of my 2013 Ford Explorer. The vehicle is equipped with an internal, chain-driven water pump that is currently failing at 100000 miles, as evidenced by coolant actively draining from the factory weep hole. Because this pump is located inside the engine block and driven by the timing chain, a complete seal failure dumps engine coolant directly into the oil pan. This is a critical safety hazard. When the coolant and oil mix, it destroys the engine bearings and causes the engine to completely seize without warning. If this sudden engine seizure occurs while driving at highway speeds, it results in an immediate and total loss of motive power, power steering, and power brakes. This defect creates an extreme crash hazard for the occupants of the vehicle and other drivers on the road. The internal weep hole provides virtually no dashboard warning or indicator to the driver before this catastrophic failure occurs. I am requesting that the NHTSA investigate this known, dangerous design flaw to force a mandatory safety recall before this sudden loss of vehicle control causes severe injuries or fatalities.