2019 FORD FLEX Complaints

The contact owns a 2019 Ford Flex. The contact stated while attempting to park the vehicle, the rearview camera became inoperable. The contact stated that the rearview camera image was blank. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The vehicle was towed to the dealer, where it was diagnosed that the rearview camera had failed and needed to be replaced. The dealer confirmed that parts were not yet available for the recall repair. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 52,000. VIN tool confirms parts not available.

The black glossy plastic applique on the Driver's Door Window Frame (also containing the Keyless Entry Keypad) blew off on the Expressway at approximately 70 MPH. While the wire harness retained the lower portion of the applique, the applique cracked from the force of the separation, for which the bottom third of the applique hung from the harness whereby the upper two-thirds of the applique became a projectile and flew onto the expressway. After sharing this with a friend (also owning a 2019 Ford Flex), he said his came off last year. Upon further studying this matter, it appears that in Ford's wisdom they only used small strips of double-sided tape to retain this; for which there are many reports of this same failure mode: [XXX] In their infinite wisdom, Ford now only sell the Applique Panel with the Keypad (Ford Part Number BA8Z7420555AC ), rendering it at a MSRP of $228.83 just for the replacement part. The Ford Parts Counter Person said they sell a lot of these, due to the poor design and retention. As this is a hazard to others on the road (e.g. potentially becoming a projectile) Ford should be forced to Recall this defect. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Rear Camera intermeitently works or completely fails. Was backing out of a parking space and could not see and a car speed by the back up warning did beep and saved the day - if my camera had been working I would have seen the on coming car a little bit sooner. it's been months since the recall was issued when will a remedy be available? this should not take this long for Ford to remedy?

The vehicle has a panoramic roof with each of the three windows having a roller sunshade. Two of three roller sun shades have failed or are not working causing excessive glare and heat in the vehicle.

UNKNOWN. The hands free function of the audio system suddenly stopped working properly. When the blue tooth links up with my phone the volume is so low it can barely be heard and can’t be adjusted up. According to my Google search of the issue it appears to be a common problem for Ford.

The water pump and timing cover gaskets are faulty. The water pump is internal and causes major engine malfunction when it breaks.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall was not yet available. The contact stated that the back-over prevention camera failed to operate as intended and the image was distorted. The contact stated that the failure became more persistent, and the screen would turn blue. The dealer was contacted. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 25,000. VIN tool confirms parts not available.

The contact owns a 2019 Ford Flex. The contact stated while driving at an undisclosed speed, the vehicle started shaking excessively and the vehicle briefly hesitated. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the water pump, resulting in damages to the engine. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 50,000.

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the back-over prevention camera image was distorted or was rotated. The contact stated that the failure became more persistent, and the images were displaying up-side-down and with incorrect information on the distance from the camera to objects behind the vehicle. The dealer was contacted. The manufacturer was made aware of the issue and opened a case. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 50,000. VIN tool confirms parts not available.

BACK OVER PREVENTION: SENSING SYSTEM: CAMERA 90% of the time, the rearview camera image is blank or has a distorted image.