2018 FORD FOCUS Complaints

My engine cracked its block rendering it useless; the 4th cylinder injector came out of timing causing all of the damage vapor locking the 4th cylinder this all occurred while at highway speeds the problem occurred at 70000 miles on a 2018 Ford focus sel this was diagnosed by the dealer and told us this is not covered because this Vin isn't listed under any active recalls involving

Engine light on for fuel purge valve . Once vehicle is under half tank it struggles to start after fueling unless putting gas to floor while still in park. Once started struggles to stay on .

Transmission control module failed, and according to Ford Service tech, basically "ate" the clutch. Vehicle can not go above 30 mph, and does not shift properly. Tech states is not included in recalls, though thinks it should be included. Parts on backorder with no ETA on resolution. No repairs able to be made. Purge Control Valve failed, causing engine to die while fuel gauge showing 3/4 tank, repeated issue until tranmission control module failure rendered vehicle mostly unusable. Tech states is not included in recalls, though thinks it should be included. Parts on backorder with no ETA on resolution. No repairs able to be made.

My car has shuddered and dies on my 3 times. 1st time with 12 miles until empty. 2nd time with 19 miles until empty and 3rd time with 30 miles left until empty. All 3 of these times were in the middle of the road. All 3 times within the last 6 months.

Cause not cranking and boost for while but stopped while running… displaying transmission fault service now… codes P1450 unable to bleed up fuel vacuum P0456 evaporative emission system leak detect..P144A emission system purge vapor line restricted/ blocked P0171 system too lean… seems to be bad vac line to tank and air leak… car stalling

The component that failed is the CANISTER PURGE VALVE. The engine light was on and we took it to a certified auto shop. Report from the auto shop: Diagnosis for check engine lamp on, run tests for codes P0300 random misfire, P0316 misfire on startup, P1450 cannot bleed fuel tank vacuum. No misfires present at this time found sticking canister purge valve pulling a constant vacuum on the fuel tank, makes is possible to pull raw fuel if the fuel level is high, suspect this to be the cause of misfire codes. Recommendation by the auto shop: Replace canister purge valve, clear computer, and retest on cold start.

Last Sunday, May 15th, 2022 my check engine light suddenly came on. Monday morning, I drove to Auto Zone and had a chip reader placed on it. Gave me error code P1450 Unable to Bleed Up Fuel Tank Vacuum. When I went to gas up that day, I was a 1/4 tank and my vehicle would not start immediately, it stalled. I had to pump the accelerator and it eventually started. This same thing happened to my 2014 Ford Escape. My Focus is a 2018 SE and has 51k miles on it. My VIN is not associated with recall, however, if this is a known problem, it needs to be addressed by Ford. I talked to my independent mechanic, and he said he’s seen a lot of Fords with this and it’s hard to diagnose. I work 45 mins away from his location, so on my end, trying to find a few days off to have my car worked on and unfortunately, I’ll have to miss work as it’s my only mode of transportation working out of the area.

The contact owns a 2018 Ford Focus. The contact stated that while his son was driving at an undisclosed speed, the vehicle stalled. The vehicle was taken to an independent mechanic where the purge valve, fuel pump, fuel tank, gasket, and fuel sender valve were replaced. The contact called the local dealer but the vehicle was not diagnosed or repaired. The contact stated the failure was related to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline). The manufacturer was not contacted. The failure mileage was approximately 49,805.

The contact owns a 2018 Ford Focus. The contact stated that while his son was driving 40 MPH, the check engine warning light illuminated. The contact took the vehicle to an independent mechanic and was informed that the canister purge valve needed to be replaced. The vehicle was not repaired. The contact took the vehicle to the local dealer and made them aware of the failure. The vehicle was not diagnosed or repaired. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline) however, the VIN was not included. The manufacturer had been informed of the failure. The failure mileage was 35,600.

the purge value and cancaster is going bad and i know some 2018 ford force had a problem with these i would like my vin to be added to the recall since it should not had went bad