2022 FORD MAVERICK Complaints

We have been informed of this safety recall since june of last year and still do not have a solution for it. We have been parking outside to mitigate fire risk. The ford dealer in Olathe KS and Shawnee KS have both been unable to alleviate this risk for our vehicle.

My vehicle was parked in a secure parking garage at work. I came out from work and noticed a hairline crack in the windshield. I took it to Safelite seeking to have it repaired and was told the entire windshield needed replaced and the windshield was “thin” and “dangerous”

While traveling on the highway at approximately 75mph the instrument cluster began to flash warnings, (Selected gear will be changed to when speed slows down, precollision assist not available, service engine soon) the accelerator pedal was unresponsive, and the vehicle began to slow. I parked the vehicle, shut the engine off, and restarted. upon restarting the vehicle would only move at approximately 10mph, the accelerator pedal was still unresponsive. I then parked the vehicle and called for a tow truck to take the vehicle to the dealership.

Had recall updates completed 3-11-24. ..23C41, 24C01, 23E09, 23E07 3-12-24 Maverick dies on the interstate going around 65mph. It just stopped running. I was able to pull over and after waiting several minutes was able to continue driving with the check engine light on. Took it back to the dealer and was told nothing was wrong. It has happened 2 more times dyeing at 65mph. 3-13-24 and 3-19-24

Vehicle had a sudden loss of power at ~40mph and began rapidly decelerating. Had there been a car behind me, the sudden deceleration could have caused a collision. Warning lamps and messages displayed on the instrument cluster instantly. I pulled the OBD codes and received U1011 and U1028 as active codes. These codes indicate a PCM software issue. It is important to note that this issue occurred after a PCM software update was performed as part of a recall. I power cycled the vehicle, cleared the DTC codes, and after multiple attempts, the vehicle worked normally again and I was able to drive it home. I have been unable to recreate the problem after clearing the codes. Prior to this incident, I have not had any problems from the vehicle. I suspect the the PCM software recall is what caused the problem.

Yes, I was driving around 75 mph [XXX] in Thousand Oaks, Ca and I lost power to the engine. No acceleration from the gas pedal. Was able to turn hazards on and make it off freeway. This issue now has happened over 5 times at all speeds. Truck is currently with Ford. Also this issue never happened until Ford fixed the CV axles that went bad. First time it lost power was the night I picked up from dealership from them fixing cv axles. They also did some recall updates with codes. I can say this is a very dangerous situation when losing power driving on a California freeway. Not having my truck is also causing me many issues with work and clients. The truck is my lifeline. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I think it's a software issue. As of today, I've had the problem three times since having my BCM and PCM reprogrammed. The truck will suddenly loose power and go into some kind of limp mode. The dash screen starts throwing notices in quick succession: low gear only, check advancetrac, hill assist not available, powertrain malfunction/reduced power, pre-collision assist not available, the light indicating what drive mode (reverse, park, drive, etc.) starts flashing and then switches itself from drive to park, and then the parking brake turns itself on.

After having two recalls done on 2/29 the next day my vehicle dashboard lit up like a Christmas tree. There was a message about low gear, the shifter was blinking, I lost collision assist, traction control, and something called bill start. I was able to pull over and shut it off. When I restarted a minute later it accelerated on its own with no input from me. Braking worked but it was slowly moving up in speed.

The contact owns a 2022 Ford Maverick. The vehicle was taken to the local dealer for recall repairs, of which three were completed. While driving 70 MPH on a five-lane interstate, the navigation screen began to ding, and alerts and messages were displayed. The service track was offline, the incline assist was offline, and the vehicle failed to accelerate above 20 MPH and went into LIMP Mode. The driver pulled over to the side of the road. The contact reset the battery and continued to drive. The service light was illuminated. The vehicle was taken back to the local dealer, who stated that the failure was not related to the recalls that were completed. The vehicle was not diagnosed or repaired. After approximately four days of driving at unknown speeds, the failure recurred. The vehicle was taken to another local dealer, Wyatt Johnson Ford (646 Thompson Ln., Nashville, TN 37204), who stated there were no codes and was unable to determine the cause of the failure. The dealer's recommendation was to download and update the software and test drive the vehicle. The vehicle was repaired. The manufacturer was not notified. The failure mileage was approximately 29,781.

Today I was driving on the highway when the precollision alert came on with no vehicles in front of me. About 5 minutes later I received a series of error messages and the vehicle went into a limo mode where it automatically drove at 20 MPH with no accelerator input from the driver. The following errors popped up on my screen. Check engine light Power train light (wrench)/reduced power Brake light pre-collision light/pre-collision unavailable Hill assist message Will engage in gear selected at low speed. Pulled over, shut it off, turned it back on, put in drive and it started accelerating on its own but only up to about 20mph, stopped and shut it off again. Turned back on and all the messages and light disappeared except check engine light remained on.