2012 JEEP WRANGLER Complaints

The contact owns a 2012 Jeep Wrangler. The contact stated that while operating the vehicle the ABS, Traction Control and check engine warning lights had remained illuminated. The contact indicated that while pressing the brake pedal to stop, the brake pedal extended to the floor causing the braking distance to become extended. The vehicle was taken to the local dealer who diagnosed that the ABS module was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure but no assistance was offered. The failure mileage was 55,000.

B1B02 driver airbag squib 1 circuit open. Airbag light keeps going on and off with loud beep. Googled code saying clocking spring

Horn and all other steering wheel functions don’t work. Appears to be clock spring

The contact owns a 2012 Jeep Wrangler. The contact stated that the air bag warning light had been illuminated. The vehicle was taken to an independent mechanic where it was scanned and diagnosed with DTC code: B1B02; for a failure with the driver’s side air bag. Additionally, the clock spring test had failed internally. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The vehicle was not repaired. The contact stated that after further investigation the failure was linked to NHTSA Campaign Number: 13V176000 (Air Bags) however, the VIN was not included. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 169,051.

The airbag indicator illuminated, and upon getting a diagnostic inspection from the dealership, the issue is the clock spring that is faulty. The shroud is another price required for replacement.

Report from diagnostic service 1-9-2023 cylinder head - has premature failure of valve guides and cylinder head replacement is required for repair. Yes, Jeep extended the warranty but if your vehicle did not show problems they would not fix it, but they did learn and knew at the point the seriousness of the problem and put an end date on the fix. Our vehicle outlasted their warranty by 30,000 but now is undrivable. Before anything serious happens as the driver drives on longer drives we have grounded the vehicle.

While interstate driving the vehicle dash dinged, I looked down to find the ABS, Traction Control and Emergency Brake came on. I immediately pulled off the interstate for a visual inspection of the breaks and brake fluid but did not see any glaring issues. I took the vehicle to a local shop, they read the code (C2200) and advised I needed a new ABS Control Module (Mopar Part #68145835AE). The local shop advised the Module is difficult to find, but they found one and would complete the work for $2,400.00 ($1,500 of which was for the ABS Module part). I called a local Chrystler, dodge, Jeep (Lou Fusz) dealer in O'Fallon to price verify the part. I scheduled an appointment for three weeks out. They also confirmed the code and need to replace the ABS Module for $1,500.00 ($881.00 of which was for the ABS Module part); HOWEVER, Jeep-Mopar told the dealership that the part is not available until March 20 of 2024 which would leave me with two options. 1) Sell the vehicle to the dealer; however, their offer took advantage of the ABS issue and was extremely low 2) Wait and drive the faulty vehicle Driving the Jeep with a faulty ABS Module may jeopardize critical systems, resulting in poor braking performance and potentially create a very dangerous or deadly situation. A search of this issue online in Jeep Forums has shown mass number of similar issues and others experiencing the same part deadly; meaning there are an untold number of jeeps driving with a faulty ABS Module. I pled to the NHTSA to please investigate and pressure Jeep to issue a Recall to ensure safety.

In my 2012 Jeep I had to replace the engine and catalytic converters. The engine number 3 cylinder failed due to excessive ware causing lower compression. After the engine (long block) was replaced, one of the cylinders was miss firing. This miss firing was traced to micro cracks in the plastic/composite intake manifold (original and not part of the engine replacement). Because these micro cracks changed the fuel air ratio on specific cylinders by leaning out the cylinders near the cracks this lean mixture would cause the affected cylinders to run hot that would lead to both the excessive ware on the one cylinder and would comprise the catalytic converters. Because this change in fuel air mixture was caused by the intake manifold and Jeep does not have any inspection requirements or methods for this item and even after the Jeep Dealer did a full diagnosis using their factory specified equipment the issue with the manifold was not found. My local AMMCO shop found the cracking in the manifold that was the route cause of the problem.

Jeep Wrangler 3.6 liter 90k miles lifter making loud noise. Seems you had a recall about this on the 2012 and guess I missed out

Clockspring failed causing airbag to malfunction. Jeep dealer ordered a replacement in April 2023 and still has not received the part(even though they have one in stock the manufacturer will not allow them to use and install the stock clockspring). We have been forced to drive the vehicle without an operating clockspring which creates a major safety hazard since the airbags may not deploy on impact.