CAN-AM Complaints

2016 CanAm Spyder F3 Limited had a bad front sprocket. Began making noise & vibrating when on the road. Took it to the dealer & it was the front sprocket that is now under recall. I had the Spyder repaired at the cost of $465.46. I notified CanAm of my expenses to replace the sprocket & provided the bill from the dealer. They are refusing to now refund my expenses for the repair. They want to give me a credit towards CanAm products which I do not want any CanAm products. I want a refund for what I spent to fix the Spyder which is now under recall & the new sprocket will have to be replaced because it is also a defective sprocket.

When making a left hand turn or a right turn at 40-45 mph it starts shaking ,I have to slow down then it stops shaking ,this could be an accident waiting to happen,,,the vehicle is a 2019 can am Ryker 600 ace

My Ryker started giving me problems going into sharp curves to the left. I have taken it to the dealership back in November and they couldn’t find anything wrong with it. The problem continues. The same curves I used to take at 55-60, now I can’t take over 40-45 without the front end feeling like it is going to slid me off the road! The bike I used to love riding and always wanted to take curvy roads with scares me now. It’s not safe! I am either going to take the curves at speed limit and chance getting slug off into a ditch or I am going to slow down 10-15 mph and have someone run into the back of me. I posted my problem on a Ryker Facebook page and had over 60 comments. I am by far not the only one with this same problem! If something doesn’t get done about it, someone is going to get seriously hurt or killed! Please make this a recall! We want to enjoy our bikes like we used to and feel safe doing it!

Gear shift paddle will not respond when manually down shifting. Sometimes, I have to pull hard on the lever 3 or 4 times to get it to down shift. Sometimes it simply won’t manually change gears. This is very dangerous, especially on corners, when you need to slow down quickly then accelerate again. I end up “coasting” around corners in too high a gear and have to brake hard to slow down enough to safely maneuver. There’s not enough torque in the high gear to accelerate out. I could easily lose control if I weren’t an experienced rider. It actually stalled out once. This is so dangerous! I took it to the local dealer, they confirmed the issue and opened a case with BRP who denied the claim. This is a KNOWN problem and they were repairing these under a service bulletin under warranty until July 31, 2021. I just purchased this bike from a private party in April 2022. The bike only had 6,274 miles on it when we bought it. Every day people are posting on Facebook Spyder pages about this issue that is unique to the 2018 Spyders. This needs to be a recall!

WHEN MAKING LEFT TURNS THE REAR WHEEL FEELS LIKE IT WOBBLES THEN THE OTHER DAY WHEN MAKING A LEFT TURN FROM A STOP THE RIGHT FRONT WHEEL FELT LIKE THE BRAKES WHERE ENGAGING THEN A LITTLE FARTHER DOWN THE ROAD MAKING ANOTHER LEFT TURN AND THE RIGHT FRONT BRAKE ENGAUGED AGAIN AND A VSS FAULT OCCURED ANF THE BIKE WENT INTO LIMP HOME MODE WHEN I CHECK THE CODES I GET C006C AND C0063 WHICH IS A YAW SENSONSOR AND A STEERING SENSOR. IT'S A SCARY FEELING TO HAVE YOUR RIGHT FRONT WHEEL GRAB WHEN YOUR TURNING LEFT. LOOKING ON FORUMS AND FACEBOOK GROUPS I SEE LOTS OF PEOPLE WITH THE SAME PROBLEM BUT NOT ENOUGH PEOPLE REPORTING IT THIS IS A BIG SAFETY CONCERN IF I WAS ON THE HIGHWAY AND THIS HAPPEND IT WOULD DEFINILETY BE VERY UNSAFE

Rusted welds. And cracks. Dealership see’s rust. Manufacturer says it’s not. Rust can lead to full failure

The contact owns a 2019 CAN-AM Ryker. The contact stated while driving 12 MPH and making a turn, the vehicle started jerking and began to lose motive power. There was no warning light illuminated. The contact stated upon making half the turn and slightly depressing the accelerator pedal, the vehicle independently accelerated. The contact depressed the brake pedal and continued to drive. The vehicle was taken to the dealer where the pitman arm was replaced; however, the failure reoccurred while driving and making a turn. The vehicle was taken to the dealer where it was diagnosed that the traction control was malfunctioning and would engage while making turns. The dealer reported the failure to the manufacturer. The manufacturer informed the dealer that the vehicle was operating as intended and that there was no failure with the traction control system. The vehicle was not repaired. The failure mileage was approximately 16,000.

VSS Limp Mode stuck on. Will not reset. Dealer has the bike, does not know what is wrong. They have called the manufacturer

While riding bike it goes into limp mode without warning because of loose steering and vibration in rear suspension. Limp mode causes the bike to travel at an unsafe highway speed. Bike throws numerous codes for suspension sensors and steering sensors.

Driving ryker down road at speeds of 55 mph and motorcycle shuts down. All power lost instrument panel off. Was able to pull over to side of road fortunately. Computer says VSS fault will not start. A Facebook member of a group suggested I check number 7 fuse. I did and it was blown. It says it’s for electrical module. It’s 10 amps. I replaced and bike worked again. Next day it blows at an intersection when I’m stopped at a light in traffic. No power again. Pull over and blown number 7 fuse again.