2008 FORD CROWN VICTORIA Complaints

Complete instrument cluster failure, no lights illuminate except turn signals. Speed, rpm’s, fuel level, temperature, are completely off instrument cluster is completely dark when driving at night, told that the solders on the cluster are bad. (Defective?)

The contact owns 2008 Ford Crown Victoria. The contact stated that the vehicle failed to reverse while the transmission was shifted into reverse(R). The vehicle was towed to an independent mechanic, who replaced the linkage. The manufacturer was not made aware of the failure. The failure mileage was approximately 115,000.

The contact owns a 2008 Ford Crown Victoria. The contact stated while driving 55 MPH in a dark area with the high beam headlights activated, the headlights became inoperable. There was no warning light illuminated. The contact stated that the low beam headlights were activated to continue driving. The vehicle was not taken to the dealer. The contact stated she replaced the headlights and the fuse but the failure continued. The manufacturer was not contacted. The failure mileage was 121,924.

The contact owns a 2008 Ford Crown Victoria. The contact stated that while driving at an undisclosed speed, the vehicle experienced a loss of power steering assist. The contact inspected the steering column underneath the hood and noticed that the steering shaft was corroded. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The contact related the failure to NHTSA Campaign Number: 13V385000 (Steering) however, the VIN was not included in the recall. The failure mileage was approximately 141,000.

The right front wheel hub broke at the weld when turning in a parking lot. The part is available for inspection. Had this happened at freeway speed, the right front wheel would have departed the vehicle. The safety hazards are obvious. I attempted to contact customer service and they did not reply.There was no warning sign and the part has not been inspected. I am not a welder. It appears this part had a bad weld from the start. I suspect it was welded by a machine and there may be more just like it from the same production run.

I purchased this vehicle a week ago and I also downloaded car fax and it states my vehicle was due for a recall in 2014 but the previous owner next got it.

2008 FORD INTERSEPTER GAS TANK STRAPS AND TANK FELL. VEHICAL WAS TOWED TO A FORD.

TL* THE CONTACT OWNS A 2008 FORD CROWN VICTORIA. THE CONTACT STATED THAT WHILE DRIVING AT 70 MPH, THE STEERING WHEEL INDEPENDENTLY TURNED 180 DEGREES. THE CONTACT REGAINED CONTROL OF THE VEHICLE, AND PULLED OVER AND PARKED THE VEHICLE. THE CONTACT INSPECTED THE VEHICLE AND BECAME AWARE OF A LOOSENED STEERING SHAFT BUSHING. THE VEHICLE WAS TOWED TO THE RESIDENCE. NEITHER THE DEALER NOR THE MANUFACTURER WERE NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 166,000.

I DROVE MY CAR TO WORK. I PARKED IT ON THE SIDE OF THE STREET. WHEN I GOT OUT HOURS LATER IT HAD CAUGHT ON FIRE.

NOTICED INTERMITTENT STIFFNESS IN THE STEERING, AN INSPECTION BY OWNER AT THE STEERING COLUMN DETERMINED THAT THE BEARING CONNECTING THE UPPER AND LOWERS SHAFTS HAD EXTENDED FROM ITS HOUSING. IT WAS DETERMINED THIS FAILURE WAS CONSISTENT WITH A PREVIOUS RECALL 13R01. THE VEHICLE WAS TAKEN TO GILLESPIE FORD IN GURNEE, IL, WHO STATED THE RECALL HAD BEEN CLOSED OUT IN 2013. THEY WENT ON TO STATE THAT THE ONLY REPAIR MADE IN 2013 WAS REPLACEMENT OF THE LOWER, EXTERIOR STEERING SHAFT, AND NO RETAINING CLIP WAS INSTALLED TO PREVENT SEPARATION OF THE BEARING. GILLESPIE FORD STATED THERE WAS NO CORROSION OR ANY OTHER CAUSE OF THE BEARING FAILURE, SAYING THAT WHEN THE RECALLS WERE DONE THEY WOULD SIMPLY REPLACE THE ENTIRE STEERING COLUMN AND NOT INSTALL THE RETAINING CLIP. GILLESPIE FORD DECLINED TO MAKE ANY FURTHER REPAIRS UNDER THE RECALL EVEN THOUGH THE CONDITION EXISTED WITH SERIOUS SAFETY CONCERNS, BUT DID OFFER TO REPLACE THE ENTIRE STEERING COLUMN FOR $1600.00.