2018 FORD TAURUS Complaints

The contact owns a 2018 Ford Taurus. The contact stated that while entering the vehicle, the passenger’s side B-pillar trim had detached. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention) and 25V611000 (Structure). The vehicle was taken to the local dealer, but the vehicle was not diagnosed or repaired. An appointment was scheduled by the manufacturer to another local dealer, Gengras Ford Service (225 New Britain Ave, Plainville, CT 06062), where the dealer requested to keep the vehicle overnight to inspect, but the vehicle was not diagnosed or repaired. The dealer declined to provide a loaner vehicle. The manufacturer was contacted and opened a ticket. The approximate failure mileage was 50,000.

Components Involved: Engine Block Mounting Boss, Intermediate Shaft Bracket (Service Part # DB5Z-3K305-CA), Factory Bolt (OEM # W500131-S437) Incident Overview: During a low-speed (about 5mph) lateral impact to the front-right wheel against a curb, expected sacrificial suspension damage occurred (snapped CV axle, separated lower ball joint). However, lateral force transferred through the passenger-side intermediate shaft directly into its carrier bearing mounting bracket. Instead of the cast mounting bracket (DB5Z-3K305-B) absorbing the force or breaking, the lateral stress sheared the cast mounting boss entirely off the engine block. Engineering Flaw & Dimensions: This design presents a critical flaw in the crash load path and failure hierarchy: Improper Leverage: The 84mm thick cast bracket acts as a rigid lever against a small, brittle ~17mm cast engine block boss. Inverted Material Sacrificing: The over-engineered bracket survives the impact, transferring fatal structural damage to the non-replaceable engine block instead of acting as a sacrificial fuse. Inadequate Thread Engagement: The factory 95mm flange bolt (W500131-S437) only utilizes 11mm of thread inside the raised boss, completely ignoring 1 to 2 inches of threading available deeper within the engine block casting. This shallow engagement concentrates all shearing stress directly at the weakest protrusion. Consumer Burden: This localized failure condemns the engine block, requiring a full engine replacement under standard dealership repair procedures. This creates a severe and disproportionate financial burden for what should be a straightforward suspension and driveline collision repair. Conclusion: I request an investigation into this structural vulnerability. The intermediate shaft bracket mounting location acts as a critical weak point, actively transferring lateral impact energy into the block and causing premature, catastrophic structural engine failure.

The contact owns a 2018 Ford Taurus. The contact received notification of NHTSA Campaign Number: 25V611000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the front driver’s side door B-pillar trim had detached. The dealer was made aware of the failure but confirmed that parts were not yet available. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 60,000.

The contact owns a 2018 Ford Taurus. The contact received notification of NHTSA Campaign Number: 25V611000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that upon further inspection, the front driver’s side B-pillar trim was loose. Several local dealers were contacted on several occasions. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 26,000.

The contact owns a 2018 Ford Taurus. The contact received notification of NTHSA Campaign Number: 25V611000 (Structure) and contacted the dealer for the recall repair; however, the dealer had failed to return the contact's call. The contact stated that the dealer had exceeded a reasonable amount of time for the recall repair. The contact stated that while driving on the highway at 55 MPH, an unknown door B-pillar trim detached. The vehicle was not repaired. The manufacturer was made aware of the issue. The failure mileage was approximately 98,000.

The contact owns a 2015 Ford Taurus. The contact received a notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while geared in Reverse, the rearview camera would not display a clear view image as intended on the center digital screen. The local dealer was contacted on several occasions. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 65,000.

The contact owns a 2018 Ford Taurus. The contact stated that upon parking the vehicle on a slightly inclined parking lot, the vehicle started rolling backwards. The contact engaged the electric parking brake, and the vehicle responded as intended. The contact stated that the failure had been recurring while parking the vehicle on an incline, requiring the electric parking brake to be engaged. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact related the failure to NHTSA Campaign Number: 18V141000 (Electrical System, Power Train); however, the VIN was not included. The manufacturer was notified of the failure and informed the contact that the VIN was not associated with a recall due to the manufacturing date of the vehicle. The failure mileage was approximately 50,000.

Odometer Fraud. The contact purchased a 2018 Ford Taurus. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the mileage was 65,000, and at the time of registration, it was discovered that the mileage was 99,000. The contact stated that the seller's father was a dealer and had advised that the issue would be corrected; however, the contact was concerned about further fraudulent business practices.

The contact owns a 2018 Ford Taurus. The contact received notification of NHTSA Campaign Number: 25V611000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that upon further inspection, the front driver’s side B-pillar trim became loose. Several local dealers were contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 50,000.

The contact owns a 2018 Ford Taurus. The contact received notification of NHTSA Campaign Number: 25V611000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the B-pillar trim had detached from the vehicle. The contact purchased a replacement trim, and the dealer, Clay Maxey Chevrolet, Inc. (1413 Hwy 62 E, Mountain Home, AR 72653); replaced the trim. The dealer was contacted and stated that the part was not yet available for the recall repair. A second dealer was contacted, Morlan - Shell Ford Inc, (1824 Porter Wagoner Blvd, West Plains, MO 65775); confirmed that the part was not yet available. The second dealer informed the contact that several other vehicle owners had been waiting for the recall repair since 2024. The manufacturer was not made aware of the issue. The failure mileage was approximately 60,000.