2014 GMC SIERRA 1500 Complaints

The vehicle experienced complete lifter failure on cylinder number 4 bending the intake valve push rod thus shutting down the cylinder. The vehicle has 167,000 miles and is well maintained. The vehicle gave no warning signs that there was a problem. Simply driving down the road, normal engine temperature, normal oil pressure, the check engine light comes on at the same time the engine begins to mis-fire. Pulling over to the side of the road, I could hear lifter noise from the right bank of the engine. The dealership (Ocean Crest Chevrolet/GMC Warrenton, Oregon) confirmed the damage. The mechanic and the service manager both state the damage is a direct result of the GM cylinder deactivation system, and every single one they have repaired has been cylinder number 4. They further stated that GM has recommended a lifter change when repairing the damage, in other words, the lifters that were installed when the engine was originally built are defective. This damage occurs on both the 5.3 and the 6.2 with cylinder deactivation, and according to the dealership, it begins with cylinder number 4. This problem has also been responsible for cam damage which results in total engine replacement/rebuild due to metal contaminating the oil.

The contact owns a 2014 GMC Sierra 1500. While the contact's husband was driving at an undisclosed speed, the contact became aware that there was smoke coming from the rear window and the window shattered. The contact stated that the defroster was operating during the failure. The contact stated that the shattered glass had fallen on the contact's minor son, who was seated in the rear seat. The son had not sustained any injuries. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The dealer was made aware of the failure. The contact was informed that the repair was previously performed and covered under the warranty. The contact was informed that the current repair was not covered under warranty. The contact was advised to contact the NHTSA Hotline to report the failure. The manufacturer was not made aware of the failure. The failure mileage was approximately 156,800.

Engine failed December 2024 at 140,274 miles. 2 cylinders failed due to lifter failure and had a total loss of power. Engine was replaced by a local shop.

hard shifting transmission and fluid smells burnt, shifts hard in the lower gears and reverse

The contact owns a 2014 GMC Sierra 1500. The contact stated that while driving approximately 45 MPH, the vehicle drove over a slight bump in the road. The contact stated that the vehicle bounced, and then there was an abnormal banging sound coming from the rear of the vehicle. The contact recently had work completed on the exhaust system. The contact took the vehicle back to the independent mechanic who had performed the exhaust repair. The mechanic raised the vehicle on the lift and became aware that the rear passenger’s and driver's side cross members, supports for the shock absorbers, and the rear sub frame had extensive corrosion. The contact was advised by the mechanic that the banging sound was coming from the shock absorbers striking the bed of the truck while driving over the bump in the roadway. The vehicle was not repaired. The manufacturer was not informed of the failure. The failure mileage was 78,569.

Vehicle stalling at low speeds Oil pressure solenoid stuck fault and P0011 camshaft fault.

The contact owns a 2014 GMC Sierra 1500. The contact stated that while driving approximately 25-30 MPH, the power steering became inoperable. The check engine warning light was illuminated due to the fuel tank cap being missing. The contact stated that the failure was related to NHTSA Campaign Number: 14V246000 (Steering). The vehicle was taken to the local dealer, where it was diagnosed with a short in the steering gear. The vehicle was not repaired. The manufacturer was contacted and confirmed that the VIN was not under recall. The failure mileage was approximately 130,000.

The vehicle’s frame has severely rusted to the point of structural compromise. My certified mechanic determined on December 10, 2024, that the frame could not pass the state safety inspection due to advanced corrosion. Welding is now required to restore structural integrity. The truck has remained inoperable and sidelined since that date. The frame is available for inspection upon request, and I have photos, repair invoices, and a mechanic’s written evaluation. This same frame was previously reworked by GMC twice: May 7, 2018 – Frame treated for premature rust. November 4, 2019 – Frame recoated after prior treatment failed due to improper descaling. Despite these reworks under GMC direction, the issue has progressed to a dangerous level. The structural integrity of the frame is compromised. A severely rusted frame puts occupants and others on the road at risk in the event of a collision, towing, or even regular driving. A weakened frame could lead to loss of vehicle control, failure to protect occupants in a crash, or catastrophic breakage of suspension or driveline components while in motion. Yes. The problem has been confirmed by an independent certified mechanic, who inspected the frame and advised that the rust is beyond surface level and requires welding to repair. They refused to weld during winter due to safety concerns and advised that the truck could not be driven or pass inspection in its current state. The vehicle was previously serviced under GMC’s direction in 2018 and 2019 by a GMC dealer (Weird GMC) to address early frame corrosion. However, the current failure has not yet been inspected by GMC directly since becoming undriveable in late 2024. I have reached out to GMC Customer Assistance and am awaiting a response. There were no dashboard warning lights or alerts for this issue. The only indications were visible signs of rust, which rapidly worsened after the 2019 rework. My mechanic noted signs of significant corrosion during routine servicing

1. while driving slow or making a right hand turn the vehicle turns itself off 2. periodically the car does not start/no power and does not respond to keyless car lock 3. periodically the dashboard panel lights will not turn off, flash or some will go off but not all All of the above have been a twice repaired GMC recall 17276 and has been occurring since 2020.

The contact owns a 2014 GMC Sierra 1500. The contact stated that the headlights were dim, reducing the contact's ability to see the roadway while driving. The dealer was notified of the failure and provided an estimate for the headlights' replacement. Additionally, the contact stated that the vehicle was experiencing excessive oil consumption, and there was smoke coming out of the exhaust pipes intermittently. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 370,000.