GMC Complaints

The contact owns a 2023 GMC Yukon. The contact stated while driving 55 mph, there was blinking on the front screen of the vehicle, impeding contact to be able to see miles per hour of vehicle, odometer, among other vehicle details the screen displays. The failure mileage was approximately 46,400.

The truck side toy down shift and the accelerator was very high…. When I was going to park the reverse was not shifting…

Transmission, going towards home up a mild hill, broke top of hill trans shifted to next gear, rear wheels locked up and tires squealed. doing around 40 mph. Took it directly into the shop, and the trans was destroyed inside. broken parts in the pan. Trans could not be repaired, had to get a new transmission. I limped to the dealership, just noisey under vehicle. There was special coverage till 115,000 mile, had 97,062 miles on it. Just like it blew up inside. I was without a vehicle for 5 weeks, but I did have an extended warranty which it paid all of it except $ 1404.01, and I had to pay 2 weeks of car rental for 893.00. The transmission $ 6782.97 , and I would like reimbursement for what I paid. I could only go 10 to 15 mph to the repair shop, which was 7 miles away. GM states it was something else at the dealership, but it was parts all over inside of the pan when they took it apart.

The contact owns a 2021 GMC Sierra 1500. The contact stated that while The vehicle while operating the vehicle a knocking noise was present coming from the engine and the check engine warning light had remained illuminated. The vehicle was examined by an independent mechanic who diagnosed that the engine valves had malfunctioned and engine needed to be repaired. The vehicle was not yet repaired. The manufacturer was notified of the failure but no assistance was offered. The manufacturer was notified of the failure. The contact was informed that the VIN was not included in the NHTSA Campaign Number: 25V274000(ENGINE AND ENGINE COOLING). The contact indicated that the vehicle had experienced that same failure listed in the recall. The failure mileage was 98,000.

The contact owns a 2022 GMC Sierra 1500. The contact stated upon shifting to park(P) and attempting to turn off the vehicle, the message "Shift to Park" was displayed. The contact waited and attempted to park and turn off the vehicle again, and the vehicle responded after several attempts. The vehicle was taken to the dealer, where it was diagnosed that the shifter assembly needed to be replaced due to internal short to the solenoid not allowing the vehicle to detect that it was in park(P). The vehicle was being repaired. The manufacturer was notified of the failure and a complaint filed. The contact was referred to the NHTSA Hotline to report the failure. The failure mileage was approximately 24,000.

The screen shakes. Goes black. Zooms in randomly without prompting. Started dialing up people from recent calls. While trying to get the navigation working. I started drifting into oncoming traffic. Fortunately was able to course correct and avoid collision. Buttons are most time not responsive to touch. It is distracting. The system has never fully worked as promised and is a distraction. And as a result a serious safety hazard.

The contact owns a 2021 GMC Yukon. The contact stated that while driving approximately driving 45 MPH and turning onto an exit the vehicle suddenly reduce speed and lost power and the message "Press Start" had displayed. The contact stopped the vehicle and eventually restarted the engine and the vehicle operated as normal. The next day the vehicle was driven to the local dealer who was unable to duplicate the problem and determine the cause of the failure. The manufacturer was not yet contact regarding the failure. The failure mileage was 42,000.

Post-Recall Low Oil Warning + Performance Issues on 2021 GMC Yukon Denali – Campaign 25V274000 Vehicle: 2021 GMC Yukon Denali, 6.2L V8 Recall: 25V274000 Owner: One owner since new (purchased 2021) I had recall campaign 25V274000 performed on my vehicle. This was the first low oil warning I have ever received since purchasing the SUV new in 2021. I have always followed the vehicle’s oil life monitor with no prior issues. The change oil light appeared at roughly 7,500 miles after the recall service (when I already had a service appointment scheduled). About one week later, the low oil warning came on. I had the vehicle towed to the dealership and did not drive it after the warning. Since the recall service, I have also experienced performance issues including noticeable stuttering that was really evident before I towed it in. The dealership initially agreed to a consumption test but later acted like it was not needed, said everything was fine, and were dismissive — blaming me for not following their sticker. I am concerned the recall remedy is not fully effective. Please investigate this matter. Thank you, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

During normal driving conditions the vehicle had set code P18A1 in the ECM. Code set due to an internal short in one of the solenoids in the valve body assembly. This caused the vehicle to display "Limp Mode" and lose reverse gear and propulsion over 45 mph. The vehicle was parked and towed to the dealership for evaluation. Upon inspection by a certified dealer technician, it was found that a solenoid had failed and required replacing. As part of the entire valve body, the solenoid is not a serviceable part. The dealership had to replaced the entire valve body assembly per repair guidelines. Per the GM and NHTSA websites, my 2022 GMC Yukon XLT with a 10-speed transmission is not included in the recalls listed below even though the symptoms are identical. General Motors publicly acknowledged the 10-speed transmission valve body and solenoid defects, including internal electrical and hydraulic failures, through Safety Recalls, Special Coverage programs, and Technical Service Bulletins applicable to 2020– 2022 full-size trucks and SUVs, including the GMC Yukon. My vehicle’s model year, transmission type, failure code (P18A1), and repair align with those documented GM conditions and should be included in this recall.

After the latest update from the Dealer, the integrated trailer brake module no longer shows an output of how much power it's applying to the trailer brake system. It just stays blank. I can tell that the brakes actually are being applied, however not having indication of them being applied and how much pressure is applied is concerning.